Counting matching models…
Easy access to all controls/ports and clears all vents. Mount that adds a VESA/tripod hole to an Epson CO-FH02 projector by attaching an Epson ELPMB65 mount to the projector. two straps that pivot on the front and snap on the back with…
A small sleeve to protect and support the SMA to BNC adapter for the antenna on a Baofeng transciever. Tested on the Baofeng UV-S9PLUS might be compatible with other models. Printed with a 0.2mm nozzle in mind, might be possible with a…
Bit holder box that is designed to hold 10 standard 2.5 inch 60mm long screwdriver bits. Lid closes with two indents and can be opened by pulling. The bits are loose fit inside the holder. A lanyard hole is provided for portability. I…
60mm screwdriver bit holder box Second version with a snap on lid is available. Bit holder box that is designed to hold 10 of 60mm long screwdriver bits. Lid closes with two hooks and won't open until the hooks are parted. The bits are…
Takes 2 120mm fans and a single 80mm fan all 25mm thickness. Sounds way more bearable now at 100% fan speed and i get -5 degrees less on the hotspot. I used 2200RPM fans to better match the old fans. Link to the fan adapter:…
Tektronix 2230 oscilloscope front cover Snap on front cover for Tektronix 2230 oscilloscope. Printed in two halves plus clips and connector for glue. Based on an ebay listing for an authentic front cover, this should fit models: 2213,…
A small sleeve to protect and support the SMA to BNC adapter for the antenna on the Yaesu FT-70D transciever. Printed with a 0.2mm nozzle in mind, might be possible with a 0.4 mm nozzle as well, i have not tested it. You might want to add…
150mm screwdriver bit holder box Bit holder box that is designed to hold 32 of 150mm long screwdriver bits. Lid closes with two hooks and won't open until the hooks are parted. The bits are loose fit and the middle bits are raised for…
This model is designed to take a USB C port for a detachable cable. A version is available with an opening for a regular USB port for the wireless dongle. Uses two M3 bolts as contacts, make sure your bolts are attracted to magnets and…
As with the original this one is made for 3mm cables, scale up to 106% for 4mm cables. Print in PETG or better for heat resistance and flexibility. Works well with 0.4 mm nozzles, no need for supports or brims. I recommend printing by…
A simple watch stand inspired by the ones that come with some watches, fits both bracelet and strap watches big and small. The holder has a D shape with a cutout for better fit and a bit of flex when putting a watch on or off. Has a…
This is a case that converts and internal 2.5" SSD or HDD to an external storage device with the apropriate adapter. The case has a few places where you can write a label. Drive is protected inside the case by two soft bumpers. This case…
This is a router guide for making repeatable and quick holes for door strike plates. Center to center spacing between the holes is 5.5", refer to picture for more dimensions. Available in left or right versions for inner or outer opening…
This is a set of cable ties. Loop over cable once on one end to keep the tie on, then loop again to hold the cable together. Available as a 10mm wide and a stronger 20mm wide version with a few different lengths. These are available with…
A clip on blade guard for the Super Benriner no.95 slicer, protects the blade during storage or transport. Clips onto the device between the two screws, screws have to be loosened a bit before putting on/removing the guard. Prints without…
This is a set of straps You can use these to hold a bunch of stuff together like wires or use them for cosplay purposes, etc. You can fold these in many different ways for different tasks and combine them together in many other ways.…
Comes with an over-travel stop to prevent unnecessary stress. Printed mine with a 0.2mm nozzle but should be fine with a 0.4mm nozzle too. Use extra wall perimeters and top-bottom shell thickness to ensure strength. Print out of heat…
I wanted my keyboard to be even more low profile, so i replaced the light diffuser and bottom case with a 3D printed version. Might fit on the high profile case but haven't checked since i dont own one. Covers the entire lower bottom of…
Made for mini files with a 3mm (1/8") shank and up to 141mm (5 1/2") long. I made it for my set of Wulken files which are the same as Libraton files from Ali-Express Holds 6 files and the handle, also available as a version that holds 15…
I designed it to be compatible with Lindt chocolates, could work with Ferrero candy too. Container can unthreaded by following the arrows. Hide your gift inside and wrap it up as if were a regular candy for a surprise. Customization You…
This is a set of parts for my modular cable ties & straps Available here: and here: Combine these with the straps for various different uses: attaching straps together, making loops, separating cables, reinforcing, etc. Many variations…
These are all currently available results.
