P
PrintablesMr_Joostik
Z mount for Anycubic Kobra 2 neo
8/10 mm the size of the holes on the printer frame. Use bearing 628, size 8x24x8mm, and use long bolts, standard short ones.
- Downloads
- 821
- Likes
- 131
- Rating
- 5
All models
Counting matching models…
P
PrintablesMr_Joostik
Vibration dampers for Kobra 2 Neo
Vibration dampers of the legs for kobra 2 neo. When printing, the printer shakes everything around a lot. These dampers reduce the shaking around. Rubber round spacers on the bottom prevent sliding on the table and dampen vibration even…
- Downloads
- 604
- Likes
- 88
- Rating
- 5
P
PrintablesMr_Joostik
HairBrush
А simple comb with very small teeth. Thin and flexible. I used PLA+ t. 210 / bed 65 / nozzle 0.4 / layer height 0.16 / the height of the first layer 0.2 max speed 30%, I'm not sure about the quality at high speeds. size 160/35/2 mm
- Downloads
- 148
- Likes
- 10
- Rating
- 5
P
PrintablesMr_Joostik
Kobra 2 Neo Aperture button
A simple button in the style of the aperture logo. I drew it with a black permanent marker.
- Downloads
- 109
- Likes
- 16
- Rating
- 5
P
PrintablesMr_Joostik
Mount C270 Kobra 2 Neo
The side mount of the camera, which rises with the head. I've attached the fusion360 project if you want to tweak something or change the camera position.
- Downloads
- 85
- Likes
- 13
- Rating
- 3
P
PrintablesMr_Joostik
GORENJE gear for meat grinder
A gear for some meat grinder, I was asked to make it. Maybe someone needs it. I printed it from PA6. The hole is made without accounting for shrinkage.
- Downloads
- 40
- Likes
- 3
- Rating
- 0
P
PrintablesMr_Joostik
Dual Z mod for Kobra 2 Neo V2
V2 {Made of sunlu petg material, the shrinkage is designed for it. Each part has an adjustment for better alignment of the belt and the shaft. The side panels are printed in mirror and feature 4 short screws M3, measuring up to 7 mm in…
- Downloads
- 31
- Likes
- 11
- Rating
- 0
P
PrintablesMr_Joostik
Soldering iron station
A simple soldering station for Alientek T80, I think, will be suitable for T80P. The mount is removable and can be made under another soldering iron. It is printed without support. A dry sponge measuring 50x35 mm
- Downloads
- 30
- Likes
- 12
- Rating
- 5
P
PrintablesMr_Joostik
Collet chuck for the engraver
А simple Pla+ collet for: a 1 mm drill / 2.32 mm wool nozzles. The lower mount is 4.85. / The upper one is 5.45 and 5.95. The inner diameter is 0.14 and 2.36. Use low speed - 30%, fan 100%, nozzle 0.2, layer 0.1. if you need a hole of a…
- Downloads
- 27
- Likes
- 7
- Rating
- 0
P
PrintablesMr_Joostik
Flashforge Chamber Heater
I am not responsible if your heater burns out. I modeled it quickly; there are things that would be better to change. I’ll change the mounts for inserting brass nuts later. I printed it from ASA, but I haven’t tested it in operation yet.…
- Downloads
- 15
- Likes
- 6
- Rating
- 0
P
PrintablesMr_Joostik
JoostCoreXY
Project in progress... Based on 3d printer Dynasty CoreXY и Ender 7 I put it out in public for constructive criticism. The printer will cost quite a lot, up to about $1,500. So far, just a sketch of my printer and frame, a lot may change…
- Downloads
- 11
- Likes
- 3
- Rating
- 0
P
PrintablesMr_Joostik
A box for wires
A box for wires with or without buttons. With and without a drawing. If you are making a drawing, then the height of the first layer should be 0.2 mm and 3 layers without blowing. otherwise, the 2nd layer will behave strongly and it will…
- Downloads
- 10
- Likes
- 0
- Rating
- 0
P
PrintablesMr_Joostik
Napkin holder with spices
I found a napkin holder on the marketplace, and I decided to make my own with a dog pattern. I left a step file so that I can change anything.
- Downloads
- 3
- Likes
- 0
- Rating
- 0
These are all currently available results.