Counting matching models…
This is a very old design. Please look at my other moderators for a current design This moderator is for air gun use only! Do not attempt to mount it to any other type of gun! Follow you local laws regarding moderators! This moderator has…
These dart cups for the 0,625" Cold Steel Big Bore blow gun are designed for 3mm steel wire. Purchasing 3mm wire and cutting them by hand is much cheaper compared to the darts made by Cold Steel. The original darts have a diameter of…
This project contains two adapters to mount a 1/2" UNF thread or M10 thread silencer / moderator to your air gun. One can be used to mount a 1/2" UNF silencer to the Diana Bandit PCP pistol and the other to mount the Diana Bandit silencer…
This is an upload of an Xbox One controller mount which vanished from Thingiverse a few days after I printed it. This works very well so I am reuploading it here. Unfortunately I only downloaded the STL with mounting hole. Originally…
Solder dispenser for up to two 250g (63x26mm) spools of solder and six 16,5mm holes for tools or flux pens. The outer dimensions of the box are 106mm long, 60mm wide and 46mm high. The angle of the tool holder is 40 degrees. . "Solder…
This is a very old design. Please look at my other moderators for a current design This moderator is for air gun use only! Do not attempt to mount it to any other type of gun! Follow you local laws regarding moderators! This moderator has…
This is a single shot magazine for the FX Dreamline that allows you to load the pellets from the left side. It works really good if you are right handed and have a pistol grip on your Dreamline. Keep your hand on the grip, cock with left,…
This tool can find the center of something with a maximum width of 30mm. The sides allow you to draw lines from 3 to 10mm distance from the edge, in 0,5mm increments. The distance to the edge is exactly below the edge of the tool. So the…
This lighter cover for the BIC Mini is for everyone who is at the point where you can only reduce your backpack weight by grams at a time. The cover has been designed with small stand offs inside to avoid putting pressure onto the flint…
This is a Picatinny / Weaver Rail adapter for an FX Dreamline with the standard air tube. The adapter requires an M3x25mm bolt and M3 locking nut. I also recommend that you spray the inside of the clamp part with a rubber spray paint.…
This corner mount is designed to be small and easy to print as no support is required. You will need two 4mm screws to anchor the mount to the wall. The Valve Index base station will attach to the mount with the original screws. WARNING…
This is an attachment for your vacuum cleaner to remove any debris when drilling holes into walls. It can suck itself to the wall even when used with an 18 volt vacuum cleaner such as the Metabo AS 18 HEPA. Design Features rotating vacuum…
WARNING: The current 3D parts are NOT compatible to PCB RC5 or PCB RC6. New parts will be released when PCB RC6 has been released as this should be the final PCB release candidate and turn into PCB v1.0 if it checks out. (Added…
Each tray can hold upto 20 12g CO2 cartridge and has holes in the bottom where the neck of a bottom tray of cartridges fits into. The 3mf file is setup for a 0,6mm hardened E3D nozzle using PLA. Check the print settings if you use…
This is a safety plug for the FX Dreamline. It should fit any caliber and version of the FX Dreamline. The plug locks the action open by preventing the pellet probe from closing forward. I don't like this personally since a cocked rifle…
I hacked these parts together as I needed a battery tray and an angled corner mount for my IKEA TRADFRI motion sensor This is the AAA conversion mount. My tray fits inside the mount. Wire the batteries in series so you get +3 Volt.…
This is a snug fitting cap for the clipper lighter. It protects the lighter from being activated while in your backpack. The cap is designed to distribute any weight onto the metal ring instead of the flint and wheel. I suggest you print…
This is my first parametric design in openSCAD. Please let me know if you encounter any issues. These M2 / SSD adapters make it possible to mount two M2 SSDs or two 2.5" SSDs in one 3.5" hard drive mounting bay. Please measure the height…
The files are for a fully 3D printed steering wheel with magnetic clutch and magnetic paddle shifters. The unit is designed to be easy to build. The electronics are just a few buttons, three hall effect sensors and an Arduino Pro Micro.…
WARNING: Do not cut carbon arrows indoors if you don't have a vacuum with a HEPA filter! You should always wear an FFP3 mask as the dust is REALLY bad for your lungs. You may ignore this warning if you vape or smoke since you don't care…
3D Printed Magnetic Paddle Shifter These 3D printed magnetic paddle shifters are designed for sim racing with an OSW direct drive wheel. The shifters should be compatible with other wheels as well but you may need to build a custom…
This cheek rest for the FX Dreamline Bullpup increases the height by 5,5mm. Use the little rubber ball and set screw from the original to secure this version.
The part is marked as WIP since I need to fix the face plate on the back. You can already use the parts if you install the original Proxxon plate on the back of the lower axis. The original files for the lower axis are off center on my…
Tripod mount for the DJI Mic2 microphones. Support for Arca Swiss connection and integrated ¼" tripod thread or with a hole for a threaded insert. Print with support and with screw hole facing down. There is a 3mm hole above the screw to…
This is a copy of the end mill holder that came with my Proxxon MF70 micro mill. My clone is slightly shorter and holds four end mills instead of the original three. Max dimension of the end mills 3,2x38mm It retains the snap open, snap…
General Info The Sackimesser from Schmiedeglut comes with a belt loop that is really good for carrying your knife at belt height. This does not work with a rucksack that has a hip belt. This dangler puts the knife lower on your belt,…
This is a small arca-swiss camera adapter plate for the Sabre Tactical stock for the FX Dreamline Compact. This adapter replaces the long front arm / rail attached to the Saber Tactical stock. The adapter has been designed around the FX…
The RND / Korad / KA3005P / KA3005D / Lab Power Supply Desk Stand will get your power supply above your desk for better access to the binding posts. The default layout produces "KA3005P 3x30mm Hidden Screw.stl" This desk stand features…
This is plate adds a picatinny rail to the Sabre Tactical stock for the FX Dreamline. It replaces the long forward arm / rail, It has been designed with the FX Dreamline Compact in mind. Watch out when printing this. You need support for…
This tool box holds three of my end mill tool boxes found at the link below https://www.thingiverse.com/thing:4386563 and a set of 6 collets for the Proxxon MF70 micro mill. Printed at 0,15mm layer height using PLA. Use support below the…
This additional tool for the Prym 390900 Vario Zange / Pliers is used to better support the back end of the male part for the Pyrm buttons when used with very thick materials. The standard tool uses one piece for the push buttons and for…
Update : I mad a new version of this adapter in openSCAD. https://www.thingiverse.com/thing:4016733 These M2 / SSD adapters make it possible to mount two M2 SSDs or two 2.5" SSDs in one 3.5" hard drive mounting bay. Please measure the…
This is a modification to the part "Parametric Lightweight MasterSpool" so it supports M3 bolts. The source works fine with M4 bolts but creates thin walls for M3 bolts. The M3x30mm STL files will work with M3x30 and M3x35mm bolts The nut…
This is a replacement handle for the Inter-Tech 2U 2098 server case series. My case arrived with a damaged handle on one side. I received a 20% discount due to the damage so I decided to keep the case and make a replacement handle. I…
These are all currently available results.
