Counting matching models…
This is a quick-to-print guard for the Creality K1's side fan, a 120mm radial fan that blows a massive amount of cooling onto the print. Someone complained of having their failed part fall into and break the fan, which inspired me to…
Based on an unpublished version for my Pixel 3a. Included is the SCAD file if you want a thicker case. Pictured is one with a 1.25mm thickness, but I've uploaded the version with 0.9mm thickness, which means the camera bar (single-layered…
This is a filament spool holder where the spool rests on the bearings for a low-friction spin. For at least one of my spools it's too little friction, so I spin it around so the spool rests on the plastic and not the bearings. It's…
This is a low-friction spool holder. It uses two of 608ZZ bearings and a length of 8mm threaded rod to hold a cylinder on which the spool rests, that has ramped ends so the spool doesn't fall off. The mount can hold spools of 32mm hole or…
A chain guard for a Shimano Crank with four mount points. It fits my bike (Shimano TY-501), and I've included the openscad source if it needs editing for yours. Mine is printed in PETG, Black for the outside layers, clear when that ran…
This is a filter for the back fan of the Creality K1, using a cheap Anko brand HEPA+Carbon filter. The filters are “Replacement Filter Set Small” from the Anko brand for their small tower purifier (sold by Kmart in Australia and probably…
This is a holder for a sample spool of filament. Customisable for the hub and spool diameter and the number of arms. You will need to print one hub and three arms (or as many as you've customised), and screw them together with M3 bolts. I…
The accelerometer can be mounted on a little platform that attaches to the right hand side of the Bullseye fanduct. On my Ender 3, it slightly overhangs the X-axis arm, but doesn't interfere with anything. This is for the print head axis…
Four (5) ways to mount a hygrometer/temperature sensor onto a filament spool. I bought the meters from eBay to monitor the humidity of my spools in storage. The first is just a connected pair of cylinders, one to fit into the spool hole…
I designed this piece to replace a few that were broken in my original Rubik's Cube 4x4x4. The design has changed since then, so the STL might be of limited value. The scad shows the measurements I've made from a few well-worn pieces, and…
For my friend's Jayco caravan, where one of the caps was missing that protects the axle grease from dust. For a wheel with six wheel nuts, where this hubcap is held on by three M6(?) bolts. The diameters of the holes for these are in the…
This is a fan duct so I can use my 40mm fan with the cii cooler ( http://www.thingiverse.com/thing:2004629 ), which is designed for a 50mm radial fan. It's an adaption of my previous duct ( http://www.thingiverse.com/thing:2225321 ), and…
I made a fan duct so I can use my 40mm fan on Thorped's duct. Not a perfect fit, but good enough. Thorped's fan duct: http://www.thingiverse.com/thing:1621937/ Fan plate source code from http://www.thingiverse.com/thing:735038 Please note…
Designed for a Creality Ender 3 or similar, that has a 6.25mm knurled shaft that sticks out 12mm from the panel. It's inspired by the combination dial (see remix), but that one's for a much shorter shaft. Designed in OpenScad. Uses the…
An adapter for your Dyson vacuum cleaner, so you can remove the lint from your Roborock vacuum cleaner, doing a better job than the supplied docking station. The existing published designs didn't fit the filters for my Q8 Max+, so I…
This is a simplified version of the original front panel, without the variable power supply, and with the banana plug and USB sockets I have.
A set of links for various brands of watch band. My wrist is about 5mm bigger than the maximum lengths of far too many watchbands, but I have a 3D printer! There are watch band links, under-clasp links and the one for my daily watch, a…
This is a filament guide for a Wanhao i3 or a clone like mine. The filament is threaded into the centre of the spiral and this can be done while the filament is loaded. The spiral looks good and should work to stop the filament escaping…
The Abus 402 comes with a mount that's at right angles to what I need, so I designed a mount that's better suited. The source is openscad so if your seat stem is a different diameter, or if you want the mount to be a different position in…
Designed for a Creality Ender 3 or similar, that has a 6.25mm knurled shaft that sticks out 12mm from the panel. Turn it up to 11! Or, edit the scad file if you want a different set of numbers. I rubbed a contrasting-colour plasticine…
This replaces the broken lever so the toilet flushes again. If your Fowler is a different model to mine but is close enough, the openscad source can be adjusted to suit. Print it at 100% infill or 99 walls, or add your own modifier to do…
A cover for the tips of your ski poles, so you can use it indoors, such as when you have a bad back and need temporary walking sticks. Can also be used as general protector for your ski pole tips or what they hit. It puts a 25mm rounded…
A fast print to extend the height of the glass dome (Ikea Harliga), which was slightly shorter than was needed to fit the clock it's a replacement dome for. The enclosed STL extends the height by 10mm for a dome of inside diameter 137mm.…
This mounts the FreeABL switch plate onto the right hand side of the Bullseye mount from https://www.thingiverse.com/thing:2759439 Create a left/right mirror of the original's FreeABL_switchPlate.stl. It's not enough of an updated design…
This is a low-height TUSH-style spool holder for mounting on a Wanhao i3 or clone. This is inspired by https://www.thingiverse.com/thing:2359860 , but its height meant my enclosure didn't fit. In the SCAD file you can adjust the bearing…
This is the LHS version of my previous design. It fixes the FreeABL switch mount to the left side of the Bullseye fan duct. The offsets I use for this in Marlin, are 50mm left, 11 in front and 4.5mm lower than the nozzle. define…
My friend liked my Roborock filter cleaning adapter for Dyson, and wanted one for her Eufy filter and an older Dyson cleaner. An edit of the openscad source, and she has one! Her Dyson is an old model, for which I only needed a pipe of…
I received a coinbox full of lock pins, so I designed a sorter for them. Inspired by the much larger bolt sorters. Use tape to join the lid. Because of their size, they don't roll easily so grab each pin by tweezers and slide them across…
I realised the sleeve that holds the scalpel in, went missing when I almost stepped on the blade lying on the floor. Couldn't find the sleeve that held it on, so designed a replacement. It's in two parts. The flat piece fits into the…
These are all currently available results.
