Counting matching models…
A mix and match of parts for a custom talon mag compatible Smiley. New parts left and right side plates compatible with @Blackpepperi_3329014's front barrel shroud left and right talon receivers from @SimonBucher_3296297, compatible with…
A slightly extended picatinny rail to match RedCowl's flat face frontend. Also fits some picatinny holsters. edit - 8-21-2023 Replaced old version of models that had untrimmed picatinny on the body preventing fitment.
Holsters a Zinc 1, 1.2 or 2. Attach to 1x2, 2x2, 2x3, molle or picatinny plate with screws / rods ~4mm diameter or friction fit printed pin key. Trigger lock works best with a 3mm screw and appropriately sized torsion spring, but small…
Replace the stock “pusher” (roller?) motor in your Ragefire for faster firerate. Fits a standard 130 size brushed motor, Krakens, Lokis, ect. Motor screws optional, the stock motor mounting bracket should be fine.
Added trigger lock so you can sprint/roll/backflip without the blaster slipping out. Trigger lock requires an m3 screw through a torsion spring. Mounts to molle pad with printed pins.
(Experimental) Run KptnAutismus's drum mag on your Diana. Replaces the “Neck” in the original files. Print 1x diana dummy lead and 5x diana dummies secondary for a comfortable feed. Fits any compatible superdrum, no hardware changes.…
Brooklyn Tony's folding stock pivot and Chance's Crush stock. A little wider for durability. Hardware - Picatinny release buttons - 2X 30-40mm 3m screws 2X pen size compression springs Pivot point and retention button 2X 35mm 10-24…
Shoot SillyShells from (most) picatinny mounting points with the Silly Mistresskey! (MistressStyle? SillyKey?) The front lever ejector means it has to be mounted at the end of a picatinny rail though. And the (relatively) long pull means…
A thicker printed stock, uses a skeggox based buttpad. There's room for a threaded rod (10-32 / 10-24) through the center for additional durability, but I haven't needed it yet. Uses 3x <20mm 3m screws to attach the buttpad
Why didn't they include a rail in the first place? Uses 4 20mm-ish 3M screws to attach to the shell.
A quick edit to put the comfy Lynx grip on the Bolt Action Caliburn, not yet tested on other AR mounting points. Remixed from - Ruppernutter's Bolt Action Caliburn - https://www.thingiverse.com/thing:5092756 - Orion Blasters Lynx -…
Experiments with angled print orientation for the slide have not turned out well, recommend horizontal orientation with supports. Remix of 118's Zinc blaster - https://github.com/118design/ZINC
Run KptnAutismus's drum mag on your Zinc. Replaces the “Neck” in the original files. Print 1x zinc dummy (still iterating) and 5x original dummies for a comfortable feed.
A quick and dirty edit of VestedClover's super cool 12 round double stack mag for my smaller printer (220x220). Also trimmed the front of the mag to interface with the original battle axe muzzle bits. Uses additional 3m screws to join the…
Prints in two halves; recommend buildplate support for each stockhalf. M3 screws or adhesive of your choice to connect.
A Rush picatinny stock point Note that this is a thinner picatinny compared to some others like on a caliburn
Use 3x 1.2mm wire by 20mm OD by 50mm compression springs ( same as that foxbat slide return ) for an automatic pump slide return. Not tested on the original Ontos shroud but should work since the geometry is the same. Sources -…
Added picatinny, front muzzle screw hole clearance, trigger lock holster, belt / molle mount EDIT - uploaded missing trigger lock piece (tlockv3)
Made it shorter, and added a grip specifically for zinc 2.0 mags. 52cm (20.5 inches in freedom units) of elastic was a comfortable grip level for me.
Twice the Pump Action Skewer. Included non-remixed parts from the Double Skewer, Pump Action Skewer, preferred pic grip, and ram. CPVC for plunger guide strongly recommended. Requires about twice* the hardware as a normal pump action…
Barely a remix, filled in the windows to prevent dust and dirt from getting into the mag
Included a decorated Arknights themed grip
Waddle around with a trusty Nightingale on molle or belt systems! Based on ehdrien's Low Profile Nerf Holster, but for the Nightingale. Uses 10, 20, and 30 3mm screws and nuts to attach the spindle and mount to either side of the…
Two Crickets Still iterating on the grip connector, it's not really better than some duct tape, but it does look nicer.
Uglier, wider, less flexible printed priming bars to help prevent catch slippage. Now requires longer 16-18mm screws.
Crush Paddle Release for people with small hands
a simple cosmetic friction fit shroud tip
Scorpion EVO Ontos but shorter. Hits ~125 with 21cm worker barrel and the weakest OOD seagull spring. https://outofdarts.com/products/worker-threaded-breech-barrels https://outofdarts.com/products/worker-seagull-tuning-upgrade-springs…
Hold a Diana + mags on a ~1.4" / 35mm standard dress belt Holster uses 2x 3m screws ~6mm Mag holders use ~55cm of 2.5mm elastic each
FetteWorst's HONKSHOT but for the Zinc 2.0 Designed to fit the 4.5 inch 6 bcar muzzle for the Znc, will fit in larger bcar muzzles, but probably not shorter ones. Assemble with mostly superglue because I'm too lazy to widen the screw…
High capacity, high symmetry, highly impractical picatinny talon magazine storage. compatible with other transwarp saya magazine tabs. Hardware requirements: 8x 30-40mm 3m screws for the arm to outer ring mount 4-8x 45mm 3m for joining…
A comfy-ish Nightingale grip derived from The Drawn Line, pasted on to Foxbat grip anchors. Pairs with the default straight talon grip top because I was too lazy to do that part. It's a little cramped for my small / average hand so caveat…
You'll need a length of 10-32 / 10-24 threaded rod and 2x hex nuts for the bolt arm, 8x 5-ish mm 3m screws for the zinc grip sideplates, 2x 20+mm 3m screws for the plunger terminator grip connection, and a bit of coat hanger wire or…
Printed rods to replace the metal rods in the default SLARPbine. Blaster flexes more than I suspect it would with the actual metal rods. Printed rods are tight so it may not be practical to fit the entire length, just as much as you can…
Uses an M5 printed pin from the protean for the battery door, tolerances may vary. I recommend a bit of scrap foam or packaging material in the battery compartment to prevent the lipo from rattling. Includes a holster system lifted from…
A quick mesh edit to fill about half the holes for surface installation
Double the fire rate of your PP with this one simple trick! Stick another PP to it with the double PP kit! (P^4? Dual-Channel PP? PPPP? Pianississimo? 2P2Furious? ) Fire one at a time, or both, or both with a staggered input with one…
An alternative Firefly pump grip M3 heat inserts optional
Zinc Grip but Ontos Should work with Ontosii that have original or close to original grip stubs
Top primed mini less hardware talon claw. Still requires a fair number of screws, aluminum flat bars, and a threaded rod for the body. Can hit 90 - 220 fps depending on barrel length and spring. Shown with ~3 inch barrel and 22 inch…
Hold a Zinc + mags on a ~1.4" / 35mm standard dress belt Holster uses a compression spring / torsion spring + 3m screw (~ 30mm) + 3m nut Mag holders use ~55cm of 2.5mm elastic each
Attach 2x warp saya talon mag holders to your picatinny side rails. uses: 2x 10mm 3m screws + hex nuts for the mag holder to the picatinny rail grip, longer screws will obstruct the magazine 1x 40+mm 3m screw for the rail grip 1x ~400mm…
A simple print to organize BCARs inside a neat looking Souper Tang tea package. Fits 5x BCARs with similar form factors to GFX or Flag and Armor BCARs.
A low hardware asymmetric mount for extra large batteries. (15X4.5X30cm, counting cable storage) Shifts the center of gravity back towards the hand, less durable. Note: cutting a hole in the buffer tube mount for the battery wire is…
Use Seagull / Harrier / 16x1mm threaded barrels with a V3 Caliburn upper Hardware 1x 16mm threaded heat insert (from OOD) 2x 3m-ish 5mm screws (flat head preferred to avoid obstructing the lower slide)
These are all currently available results.
