Counting matching models…
The original model is a bit tiny and has some “solidness” issues. I made it manifold and simplified the mesh by 70% so it's faster to open in your slicer and easy on CPU. I've also reworked the tail to improve the overhang and make it…
Understanding the tolerance It's an additional gap left while designing in order to make moving parts move freely and as smooth as possible without being too loose at the same time, like holes, screws, connectors… It has to be considered…
The idea was to first have a fully printed object. Secondly, a mechanism that would permit to higher the strenght by pre-compressing the spring. It was initially destinated to participate to the contest, but I couldn't finish it in time,…
Here in France, a refill cartridge contains 8 capsules. The new design is now provided in 3 variants and sizes. Sizes / Capacity : • M : 9 capsules • L : 13 capsules • XL : 17 capsules Objects are optimized for a line width of 0.5 mm.…
Those provided with my E3DV6 hotend have finished being too loose and good for trash. The one I've modeled is bigger, better, stronger. Recommended settings Ø 0.4 Layer height 0.1 Perimeters 2 Infill Bottom & Top 7 7 Supports
Updates : • 23/04/2025 : added classic variants • 04/09/2023 : added low poly models This is a slight remix with litte changes in designs. These objects should be even more easier to print and don't need supports. As always, rotate the…
Made on a colleague's request. Because it's oriented at 35°, no supports are needed. Print it as is. Ø 0.4 : Layer height : 0.25 mm Perimeters : 1.2 mm Bottom/top : 1 mm
This object will need only about 2 grams of material and should be printed in less than ten minutes with proper settings. Print settings suggestion with a Ø 0.4 mm nozzle : Layer height : 0.25 mm Wall lines : 2-3 Top/Bottom : 0.75 mm…
It looks so elegant, isn't it? Changes : v2 has a slight shape revision to make the body a bit smoother.
This is “Duo Clip” or “D-Clip”, yet another filament clip but… It combines two kinds of clips, letting you the choice of holding the filament following your needs or just as you like. There are two spacings for now, 3 and 4 mm. They…
This model is a bit larger than a regular part.
Euro coin official size : Ø = 23.25 mm | H = 2.33 mm Recommended settings \_/ Ø 0.4 Layer height 0.1 Perimeters 2 Infill 100% Bottom & Top 4 4 Supports
Replacement cap for 400ml WD40 or similar containers. "clic" and it's in place ! If this becomes too hard to remove, slightly scale it up finely (like ~0.1-1%). Recommended settings \_/ Ø 0.4 Layer height 0.2 Perimeters 2 Infill Bottom &…
Sometimes, the stock screw brakes up. Why buy a new one when you can print it ? Note : if you use PLA, it's known to be fragile so you should not go over 0.2 mm of height and over 40 mms speed to let layers fusioning well. Or better use…
Tested on Dualsense, Dualsense Edge, Dualshock 4. Very helpful in GTA online : ) V2 from 25/01/2026 : new design featuring a handle Recommended settings \_/ Ø 0.4 Layer height 0.1 Perimeters 2 Infill 40% Bottom & Top 4 4 Supports
As simple as praticle. All tools can be reversed. History : • 2024/12/23 : Return of the “FaucetAeratorDriver” but redesigned • 2024/12/05 : v3 is a contest update, smaller tolerance and new designs to reduce amount of material even more…
Tool designed for filters with an outer diameter of 80 mm and 15 flutes. It has to be strong, so don't try to save much material on this. The V2 is a bit tighter so it might fit better if the V1 is loosy. Tool size : 154 x 100 x 12…
The print time should not excess 5 minutes. The base has a negative expansion in order to compensate for the “elephant foot”. 1.2 mm of wall thickness and 100% infill are recommended to ensure a minimum strength.
Due to the thread, I strongly recommend to print this at 0.1 mm layer height. It should fit well but if not, scale it by increments of 0.01%. Don't forget to re-use the rubber seal : ) Buse pour pulvérisateur à pression Une hauteur de…
Wheel chock / Cale roue I higly recommend the gyroid infill pattern with 20% infill at least. This needs to be strong . Don't try to stupidly save material with such an object, please ! Life is priceless ! With an average print speed of…
I was inspired so I made this for a collegue's birthday. 2024/05/08 : Added a larger model to improve stability
I ordered some on aliexpress, but they are too loose and thin, still dropped while driving. This design doesn't require supports, but you shouldn't print it at over 0.15 mm / 40 mms. Recommended settings \_/ Ø 0.4 Layer height 0.1…
Designed for Ø15 mm tubes. Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.25 0.25 Perimeters 4 3 Infill Bottom & Top 4 4 4 4 Supports
Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Tip : print the sample test first to…
Last change : 2025/11/08 I've designed these objects in order to save time and material during pure calibration phases. The larger the preciser (logically). Although the rounded corners should not interfer with measurments, a bad jerk may…
Alternative calibration cube that is larger and doesn't require much material because it's sunken. Setting a brim skirt is advised if you don't use any extra adhesive stuff like me. Wall thickness : 2 mm Main mesh : 40x40x40 mm Additional…
An average 1 hour of print and works pretty well.
Dimensionnal accuracy will make the difference. Scale the clip by increments of 0.01% according to how tight you want it to be. This has been tested with regular PLA only. If you use a stronger material, decrease wall loops and/or infill…
This object is designed to be printed in place. The hinge is strong and has a tolerance of 0.4 mm. Once folded, it's clipped and will stay closed. 2026/04/08 : v3.1 is a highly optimized version with small tolerances (0.25 mm), thus…
I've edited the original object to make it flagless and textless. There is also a simplified version that is less hard on CPU/slicing.
A cool holder that you can drill, glue or whatever you'll decide to stick it. Its design was inspired by a similar object seen on aliexpress and a manta ray. I recommend 5 wall lines and 0% infill so you'll get a minimum total of 4 mm…
This is a simple conical piece which will guide the filament right to the connector's hole. This might change your life if you often switch between different filament colors or materials. Lifehack - 1 | Headache - 0 Recommended settings…
Simple and effective design. Recommended settings \_/ Ø 0.4 Layer height 0.25 Perimeters 2 Infill 20% Bottom & Top 4 4 Supports
Euro coin official size : Ø = 23.25 mm | H = 2.33 mm Recommended settings \_/ Ø 0.4 Layer height 0.1 Perimeters 2 Infill 100% Bottom & Top 4 4 Supports
I made this in order to pour water from any regular bottle easily and see the level at the same time. This object is optimized for both 0.4 and 0.6 nozzles thanks to the 2.4 mm wall thickness. Bottom Ø : 100 mm Top Ø : 110 mm Recommended…
The normal object has an even thickness of 2.4 mm so it is optimized for both 0.4 and 0.6 nozzles. Disable infill in order to print only the shell thus reducing print time drastically and avoiding unnecessary moves. It will also prevent…
Motorola walkie talkie case that you can hang on almost anything with zip ties or else (max 7.5 mm large). Recommended settings \_/ Ø 0.4 Layer height 0.25 Perimeters 2 Infill 20% Bottom & Top 4 4 Supports
Who doesn't like the hex pattern? Dimensions : 100 x 80 Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.25 0.25 Perimeters 3 2 Infill Bottom & Top 4 4 4 4 Supports
English Here is a drum paddle that I've reproduced, based on the following model . This part is commonly used in a wide range of mid-end devices. ABS or any high temperature resistant material is strongly recommended, unless you cold wash…
I made this to clamp my PEI sheet but it can serve for other things as well, of course. The object There is a moving plate that have a clearance of 0.3 mm. If it's stuck, just push a bit to release it. Ø 0.4 recommended settings : Layer…
Size : 350 mm x 282 mm Thickness : 0.6 mm Yeah, it's not meant to be small so the model is quite big, although you can scale it down reasonably. At full size, the print time should be around 1h with a classic 0.2 layer height.
This spool holder is made to be fully printed. The bearing ( remixed from Emmett's one ) comes with two different tolerances, one with 0.2 mm and the other with 0.25 mm for convenience, just in case. All objects are optimized for a layer…
Features : • A little window to look trough for viewing the nozzle • Holes on top to help the heat dissipation • Supports for blower fans • Wedges to hold the blowers for easier screwing • Ducts that slightly compress the air for more…
This was originally for 3D rendering purpose but I decided to share it for fun. Printing it upside down as is won't require supports.
Just a pumpkin trying to make ghost friends.
This is designed to slightly compress air and head the flow efficiently. Printable without supports. Recommended settings \_/ Ø 0.4 Layer height 0.25 Perimeters 2 Infill 20% Bottom & Top 4 4 Supports
My vision of a practical tube squeezer. My GF asked me to print one, I told her that I would try my own design. And voilà. Recommended settings \_/ Ø 0.4 Layer height 0.25 Perimeters 3 Infill 20% Bottom & Top 4 4 Supports
Spool holder featured with V-slot wheels. There are two parts for each side that needs to be assembled with bolts. 3 bolts are required per side. The only thing you'll need is a T10 sized torx screwdriver. There is also a sample test, I…
Designed to fit in my coin clip . Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.1 0.1 Perimeters 3 2 Infill 50% 50% Bottom & Top 5 5 5 5 Supports
The model is solid, it's designed to be printed in spiral aka vase mode. I recommend to define the line width to 0.8-1 mm and the layer height to 0.3 mm. It should be done in less than 15 minutes with an average print speed. I originally…
As requested by a friend, I've reproduced a "vertex cap" for Burberry umbrellas. Since there is no repair service (even at Burberry), this will replace broken or loose objects. I recommend ABS material or similar because it needs to be…
I made this for a colleague's birthday. It is based on the official emblem but I've normalized it so it is optimized for 0.4 nozzles. Thickness and spacing are evenly distributed. 0.25 mm of layer height is the optimal print setting as…
Size : 100 x 80 Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.25 0.25 Perimeters 3 2 Infill Bottom & Top 4 4 4 4 Supports
This one is made specifically to match device's design. Original request by wavapps : https://www.thingiverse.com/thing:3465870/comments Still, I recommend to print it at 0.15 mm of height. Or, don't go over 0.2, you'll lose accuracy for…
To drop stuff in it. No support and no multicolor module needed. Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.2 0.2 Perimeters 4 3 Infill Bottom & Top 4 4 4 4 Supports
It looks simple and creepy at the same time. Note : “deep” version has deeper mouth and eyes so less good overhangs.
I made this for my needs, because I'm using my own side spool holder. Just unscrew the nut enough to glide the piece so the notch fits on screw's axis, then re-tighten. v2 : slight rework of the torus ring in order to enhance bed…
Navigate and edit values with convenience. Recommended settings \_/ Ø 0.4 Layer height 0.1 Perimeters 2 Infill 20% Bottom & Top 5 5 Supports
Useful if you have only one battery and don't want the liquid to potentially flood the resistance while the clearo is leaning. Recommended settings \_/ Ø 0.4 Layer height 0.2 Perimeters 2 Infill 20% Bottom & Top 3 3 Supports
Optimized for 0.5 line width. The “solid” version is meant ot be printed in vase mode with zero bottom/top. Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.25 0.25 Perimeters 2 2 Infill 10% 10% Bottom & Top 4 4 4 4 Supports
Very simple design and look. Easy to paint in slicers like Orca.
The moving pressing plate has a clearance of 0.3 mm. If it's stuck after the print, just push a bit to release it. Recommended settings \_/ Ø 0.4 \_/ Ø 0.5 Layer height 0.2 0.2 Perimeters 2 2 Infill 20% 20% Bottom & Top 5 5 5 5 Supports
Show your super print capabilities with a super item. Easy to paint in Orca thanks to the edges. Multicolor parts included.
These are all currently available results.
![Faucet Aerator Wrench & Tools v3 [24 mm]](https://media.printables.com/media/prints/1094252/images/8449547_939697b7-9971-4c40-baec-6d48fe32a572_18e6f731-c9f2-44ff-9f79-f4303836602e/preview_v3.jpg)
![Clothes / Peg Clip v2 [ Ø15 mm ]](https://media.printables.com/media/prints/8e431d36-5328-44b2-bd32-a40686e3fe90/images/11288141_12d989c9-b09f-4cda-8f76-314d8d4f2bdb_83b676b2-7a07-430c-a559-b6174cd5ec46/preview.jpg)
