Counting matching models…
After seeing one I wanted a straw clip to fit all the WD-40 cans that I had and after next to zero searching I decided to make my own Its should work for most 660mm diameter recessed rim cans I did print this on my A8 as the tolerances…
The original design was developed to be machined out of aluminium. It was discovered that the test print works just fine as a mount. Redesigned the mount to have a higher safety factor at the stress concentration. Recommended to slice…
A wall mount for tool holders for 6" - 9" quick change tool post, commonly used with 7"x12" mini lathes. The wall mount supports tool holder with ~30mm wide, ~6.5mm deep, 60 degree dovetails. The quick change tool post is commonly marked…
I adjusted the angle of the water holes so it should reduce the amount of water that dribbles down the side of the pail from surface tension. I completely forgot how I printed this so ¯\_(ツ)_/¯
Have 2 versions. v6 requires heatset inserts and v2 just uses the screws to thread the part The v6 also adds compatibility with a backplate made from the stock anet a8. 4 holes have been clearanced for the bolt heads so the adaptor can be…
A wall mount for tool holders for 6" - 12" quick change tool post, commonly used with 7"x12" mini lathes. The wall mount supports tool holder with ~43mm wide, ~9.8mm deep, 60 degree dovetails. The quick change tool post is commonly marked…
The 4040 Extrusion X Mount should be printed with ABS or ASA (I suppose most filament should be fine) 40% infill 4 walls 0.2mm layer height 0.4mm extrusion width 5 top / bottom layer (Aka Standard Voron Settings) Important Note on the…
The fitting takes 6mm tubing but the F360 model can be modified to take any tubing. Print with 0.1mm layers, 0.4mm nozzle, supports, and fill the entire model with all walls. (6 walls can work)
I just wanted to make my M30x immortal so yeah I tried printing this out of a bunch of different filaments but I found that PETG is the best material for it. So far I tried random PLA+s, ABS+s and PETGs Most PLA+ lasts around a month,…
Was too cheap/lazy to find and buy a proper tool Compatible with the Columbia CA025 E15 Watch and possibly others It just prints with no supports and almost any infill and at least 2 shells
Project done in collaboration with @Print3DPilot We wanted to upgrade an Anet A8 Plus to a Stealthburner. We initially thought the Voron Legacy part would be a drop in fit but the distance between linear rod centres were 40mm vs ~50mm on…
The head band is printed from petg and the ears can be made from anything. Alternative headband with Audio Technica M30x compatibility The servos are held in to the ears with the self tapping screws they come with. For the headband just…
Printed in PLA with 2 shells, and ~10% infill at 215C (Slicer settings will need tweaking for optimal strength) Non-printed parts list (Some parts may be substituted): 8 M3 Nylon Nuts 4 M3x16mm Screws 3 Brotherhobby Returner R3 1106 3+…
Compatible with 5.7mm or 4mm length M3 heatset inserts. Hole has tighter tolerances to improve insert adhesion. Before installing the carriage make sure the extra material ejected from installing the heatset insert is removed, ideally by…
A wall mount for MT2 machine taper tools and collets, commonly used with smaller lathes and some mills. The part is intended to be printed upside down without supports. The wall mounts uses a pair of 1.5" long 0.25" countersink head wood…
Added a 2mm self tapping screw to reinforce the guidler
50mm Face Mills break the PLA printed gears Otherwise most of everything is fine This model was initially built to be lost PLA cast.
A wall mount for R8 machine taper tools and collets, commonly used with bridgeport mills and most other mills. The part is intended to be printed upside down without supports (Figure 2). The wall mounts uses a pair of 1.5" long 0.25"…
Im going to write this later, Im just going to post this and deal with it later Differences between models: Regular Size: 94mm Tall Enlarged Size: 110mm Tall Generic: Removes the voltage and amp hour text on the side of the case RMB: The…
Print in TPU with out supports Requires M2.5 Bolt ~6mm Length
Replaced the M3 pocket nut in the MiniSB_Bowden_M10 with a 4mm M3 heatset insert
An older project that I wanted to upload. I wanted to mount a 3rd 2.5in drive in my node 202. Mounts in the GPU / radiator area with M3 screws and washers. Compatible with short GPUs or single fan radiators Recommended for use with SSDs…
The uploaded model is for a a 68cm wide and 54cm tall opening window I expect it to fit basically no other window. Solidworks file are included for modification. The window insert uses M3 heatset inserts and M3 x 12mm bolts. The top part…
Case for preventing the chain wear indicator from being accidently bent and reading good chains as worn chains. The case uses a filament hinge. Includes a outline of the indicator to house it with the inverted image on the lid for…
These are all currently available results.
