Counting matching models…
Update 1/6/2025: Added two additional 30mm wide clamps (and their respective bottom bolts) to fit thinner desks. The “Clamp 30mm Wide 30mm Thick.stl” clamp will fit desks less than 30mm thick and the “Clamp 30mm Wide 45mm Thick.stl” clamp…
This small santa hat has a special trick: it balances! Printing Instructions (Standard): I recommend PLA with 0.2mm layer height, 5-10% infill, 2-3 walls, and no supports! Print as oriented. I printed in matte white PLA and colored the…
This is a standard pencil holder that has been designed to be as lightweight as possible. The front two sections are the perfect size for pencils and markers, and the back section is large enough for scissors. I have included 3 versions:…
Voronoi deer with a simple baseplate. The base acts as a permanent brim and keeps the print from falling over while printing and while displaying. Printing Instructions (Standard): I used PLA with 0.2mm layer height, 10% infill, 3 walls,…
This is a picket fence created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions (Standard):…
This is a telephone pole created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions…
This is a round container with a knurled texture and screw-on lid. There are three sizes, each 60mm in diameter: 40mm, 80mm, and 200mm tall, each with and without internal dividers. The 80mm tall version is perfect for 3in Q-tips and the…
This is a gas station created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration. I designed this model to be printed without an mmu or ams equipped printer by manually changing…
This is a picnic table created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions (Standard):…
This is a girder bridge created for an o-scale 1:48 model train layout. Although it is intended to fit Lionel Fastrack, it should also work for any o-scale track. I have included the standard 10in version as well as an 8in version that…
These sink caddies organize your soap dispensers, sponges, and drain plugs! The bottom is sloped to catch and drain water. I have designed two organizers (compartment dimensions given): one for a hand soap dispenser and a dish soap…
This is a bench created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions (Standard): I…
This is a remix of my previous modular coffee cups stand. I thickened the arms that hold the coffee cups after breaking a few of them off. Original: https://www.printables.com/model/1103572-modular-keurig-k-cups-coffee-pods-stand…
This is a simple necklace stand that has 24 hooks. The top wheel rotates freely. Each part prints separately and can be pushed into place. Although not required, you can superglue the non-moving parts to increase rigidity. Printing…
This is a ranch-style fence created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions…
This cup holder attaches to a lawn chair or foldable table. It uses a clamp with two 3mm bolts and nuts to clamp to a vertical tube leg similar to a handlebar mount. The maximum tube diameter is 30mm which should fit on most chairs. The…
This is a railroad crossing created for the Lionel o-scale Fastrack system. Use superglue to glue the parts onto the track. Printing Instructions (Standard): I recommend PLA with 0.25mm layer height, <5% infill, 2 walls, and organic…
This is a wider version of my single-rowed power strip desk clamp that fits wider power strips up to 142mm or 5.6 inches allowing you to fit your 2- or 3-rowed power strips to the edge of your desk. Printing Instructions (Standard): I…
This is a simple bracelet holder stand that can be patterned to hold as many bracelets as needed. Each stand has two arms to hold at least two bracelets, but I've found that as many as 4-5 bracelets can fit on a single arm. The stands can…
This is a modular stand for Keurig K-Cups coffee pods. Each module contains 8 slots to fit 8 pods and can be stacked as high as needed! Each module spins individually and requires no additional hardware to assemble. Printing Instructions…
This is a Lionel O-Scale 10in Fastrack straight section reference that I use for making track accessories. I have also included the sketch dimensions I used if you're curious. Find more of my model train prints in this collection , many…
Countdown all your favorite holidays with these numbered blocks! The blocks contain every digit (0-9) as well as duplicates of 0, 1, and 2 for countdowns up to a month in advance (the 6 also doubles as the 9). This is a set of countdown…
Here is a stylish simple organizer for you desk or office space. The basic design includes a drawer, shelf, and pen/pencil holder. The top shelf of the organizer is the perfect size for a 3in by 3in (or 76mm by 76mm) Post-It note. The…
These are a couple of Halloween bat silhouette decorations designed to be lightweight and to be printed multiple times. A single bat at 100% scale is about 2 grams, and at 200% is about 10 grams. The bats are about 10mm or 4in long. Feel…
Three pumpkins stacked on top of each other. Printing Instructions (Standard): I recommend PLA with 0.2mm layer height, 5% infill, 2 walls, and plenty of supports around the bottom. Print as oriented. Please comment with any questions or…
This case is perfect for traveling with small things that need to be sorted. It has 12 compartments with lids and 2 extra compartments without lids. The case is held closed by 4 magnets in each corner. Each compartment is about 25mm wide,…
This is a clamp for a picnic table at a campsite with a tray to hold a bar of soap. The tray is slanted and has ridges to allow water to drain and the soap to dry. The clamp can be used on tables up to 1.5" or 40mm thick. Printing…
This is a collection of Christmas-themed girder bridges created for an o-scale 1:48 model train layout. Although it is intended to fit Lionel Fastrack, it should also work for any o-scale track. I have included an 8in version that should…
Simple inserts for the double-sided 34-compartment small parts organizers on amazon. I used this to divide a few compartments to organize some very small ceramic capacitors and a few different types of LEDs. Each insert has a label and…
These are all currently available results.
