Counting matching models…
Note: there's some weird behaviour of the organic supports, so there are some places in the print that are not ideal - but it prints. The playsation controller model was created by Saba.Lanchava The current contest inspired me to create a…
NOTE: This model is a prototype. I tried to catch as many issues as possible, the model works for me, but there might be other issues. Any feedback will be appreciated and found issues will be fixed in next version. New, improved version…
This is updated version of my MF-01X conversion. Designed from scratch, it addresses feedback from users as well as my own findings and ideas. This version is much more modular, I will post number of modifications as remixes and encourage…
I needed a simple stoper for a window that doesn't have ventilation, and I liked simple design of the original model. But my use needed a few modifications. For wide enough opening, the latch had to be longer. The window frame would get…
This is my model inspired by FF-02. I recommend printing from PETG, 4-5 perimeters, 0.2mm layer height. The chassis brace parts require supports, other parts can be printed without supports. The base for the model is an M-05 in L…
Check out the V2 version: https://www.printables.com/model/1429291-tamiya-m-05mf-01x-bumper-v2 After I broke the original design several times, I decided to make a reinforced variant. I used KmanSweden's model as a template for basic…
Attention!: Models were taken directly from my prototype, in which I didn't do corrections of dimensions. They will need some post-processing for perfect fit! Update: New hub carrier extension design, this time tested and assembled. This…
As the original mount of MF-01X isn't really li-po friendly and leaves the battery exposed, I designed this cover to properly hold the battery with enough clearance for wires, but also as an additional protection. The battery will be…
This is extension of MF01X to 257mm wheelbase (as original extensions can be stacked only to 254mm), based on my early design. I modified it to include some space for electronics. Two halves are connected by pillars, which can be printed…
This is a bodypost brace I designed for my MF-01X conversion, but it should work for other Tamiyas with 6mm bodyposts and 70mm spacing. It can be printed without supports.
Update 14.Feb 2026: Added new variant with lowered damper mount. This model aims to improve front suspension geometry by using modern Tamiya M-chassis uprights, which move outer hinge pin 6mm closer to the wheel without change to the…
Check out beefed up Version 2 Ever since I made my FF-05 conversion , I've been thinking about increasing steering angle, since I intend to use it in RC rally, which requires tight turning radius. One discussion prompted me to take a…
Warning! Do not use if you have a destructive pet. Design contains small metal parts that could hurt the animal. This is a simple model I made to prevent my dog from escaping the house. Octagonal shape is a bit easier to grip than round,…
Attention!: Models were taken directly from my prototype, in Which I didn't do corrections of dimensions. They will need some post-processing for perfect fit! For my MF01XL project, I needed longer arms - originaly, I intended to use…
Curved suspension arms, nicknamed “bananarms”, designed for use on MF-01X or M-05Ra - however, design should be compatible with other Tamiya M-chassis with same suspension design, because outer dimensions are identical to the stock arms.…
Remix of the MakeChetti's tensioner case, I found out that the belt is a bit too high and rubs on the extrusion instead of running inside. This version keeps top side roughly in level with the stepper pulley. Category: 3D Printer Parts
One of the advantages of separate suspension mount is, that different parts can be used to setup rear geometry. These mounts allow to add or subtract one degree from rear toe-in - stock being 2°. Mounts are marked for easy identification.…
The extension doubles as a receiver box (fits only compact receivers), to provide limited splash resistance and neater cable management. I uploaded stp file, so you can easily make your own wheelbase.
Thanks to Poor Boys RC speed challenge, I got this idea. It reuses stock MF-01 34T/24T spur gear in place of the original 37T/21T, to achieve lower gear ratio. The mod supports 21-33T pinions with FDR ranging from 4,44 to 2,83. Its…
New version of my previous design. Main features: Uses standard TT-01/TT-02 bumper foam (modifications required) Clears large tires on the MF-01 off-road variants It can be used with front mounted body posts (#51253) Thicker top plate…
Modification of rear damper tower, which includes short top links identical to M-05. This modification isn't included in the base model, because it requires additional parts: #50797 5mm short adjuster 2x 12mm step screw or #54182 M-05…
This is an unfinished model! The project never moved beyond the test assembly shown on photos. However the transmission spun, so it should work. But modifications will be needed, because the design was never properly optimised for 3D…
This model allows increased stering angle, like the previous model, but has sturdier geometry. It includes new steering post stays which use 19808016 steering posts, which reduce play in the steering system. The steering arms are now 1mm…
This is model I designed to make XV01 compatible with brusshless motors with tabs over the can, like Hobbywing Justock series. It replaces the stock KK1 part ("motor stay"), with extra space for motor tabs and cables. It allows routing of…
Over the span of the past year or so, I worked on improving my design based on suggestions from people who drive it, as well as issues I found myself. Based on this, I made following updates: suspension block screws moved inward for more…
These are all currently available results.
