Counting matching models…
My usual watering schedule for potted plants is adding water until it comes out from the drainage holes on the bottom. In this case it would be a problem, since the small vases don't have any! I just added them in order to avoid having…
My own 3d model of a 120mm fan, more specifically a 200 cfm 120mm EZDIY-FAB fan . I needed a 120mm fan model for a fume extractor I designed, so I took some time and modeled the fan aswell
This is just a simple mount that you can screw an SKR Mini E3 V3 to, in order to avoid shorting the bottom pins accidentally. I have been using it on my main 3d printer until I decide how to permanently mount it
Adapter used to mount a Klipper Expander board to a standard DIN rail. Useful for voron 3d printers in particular. Print using supports on the two overhanging tabs
Nothing fancy, just a wider version of the original din clip (4mm wider)
Replacement cable cover with support for pg7 cable glands and passthrough for endstop switches
Simple case used to mount your Aubess Mini Smart switch on a DIN rail. Use 2 M2x10 self tapping screws to attach the case to the DIN clip You can either wire up the smart switch before or after inserting it in the case, there are holes…
After trying out the original nozzle park and brush mount I noticed it was a bit finicky to setup, so I went ahead and designed my own version: my project incorporates the adjustable dock from klicky00 which allows fine-grained z height…
I was asked to create a version with less gem holes, so I just rebuilt it from scratch and added various variations. Print it upside down, with the gem holes touching the plate. The overhang is at 45 degrees so you won't have issues…
Made for a friend that likes diamond painting, this adapter fits on the usual pink pen included in the sets, and allows to place up to 9 diamonds/gems at the same time. This version has bigger holes to fit the diamonds but unlike the…
Mount for an M10 GPS module, to be installed on the back of an Apex HD frame. It sits over the VTX antenna and is tilted back by 20 degrees. The apex frame's top plate has a convenient hole to pass the GPS cables through for a clean…
Do you like trekking? Or maybe you like the cool pattern a trekking shoe has? Want a cool backpack keychain? Then this thing is for you! If you have a TPU-capable 3d printer, make sure to print it using that, the flex factor just makes it…
Why When determining the maximum flowrate for a specific hotend/filament combination I always use the poop method , in which blobs of filament are extruded and weighted to assess the capabilities of the setup tested, but this time I…
Simple mount for the Orange Pi 3 LTS, that in conjunction with this PCB din clip allows mounting it to DIN rails, especially for use in the electronics compartment of a Voron 0 3d printer
I needed to make a case for my mini smart switch, so instead of just taking its measurements I modeled it from scratch to simplify my work later
Wanted an easier to print version of the original model I found on thingiverse, and since I didn't find one I just modified it by myself. This version doesn't have weird 90 degree overhangs anymore, so no supports are needed.
Mount for the SFS 2.0 that allows mounting it on an horizontal extrusion and keep the filament path orizontal
Adaptation of the original model to allow using led strips with 60 led/m instead of 30
I really liked the original model, but after starting to print it I noticed it had a number of flaws or incompatibilities with my kit ( https://a.aliexpress.com/_EHHvSdO ), so I fixed it. This version works for sofle keyboards that use…
Got a simple but functional display holder for my wife's creations. Splitted in two parts, one with male connectors and one with female ones, just open it wide and put the pizza plate on top! Designed in order to make the pizza plate…
Took inspiration from this ( https://www.thingiverse.com/thing:4760273 ) thing and remodeled it from scratch, to allow one more todo list entry. Since I always had my pen lying around in various places, I then modeled a pen + postit…
I haven't found an antenna mount that allows mounting my generic ELRS receiver to my Apex HD frame. Specifically, I'm using this receiver with the pictured antenna Just insert the hex standoffs into the printed piece, insert the antenna…
Snap-fit case for a Wemos 18650 battery shield V3 case. There are cutouts for all power outputs so you can route out wires Simple print, use 4 M3 button head screws to secure the board to the holder Changes to V2 added fillets to the…
Simple change to the original clip to remove the need of supports or drooping overhangs
A simple holder for my model making pigments, to avoid having them all over the place when I'm not using them. It's a 4x3 design, with space for bottles up to 35-36mm in diameter (based on your printer tolerances). Tested and working…
Reworked the keystone holder to work with my specific model
An over-engineered fume extractor, very useful when you don't want to inhale toxic fumes from tasks like soldering, pirography, airbrushing etc. There are existing designs that accomplish this task, but I wanted a robust object that could…
I needed to create a custom case for a filament runout sensor I had laying around. Since I had to measure most of the PCB it uses I just took some time and modeled the entire assembly! The sensor I used as reference is the usual one you…
This project aims at improving the usability of the Voron 0.2 printer when enclosed, by having a plug-and-play exhaust system similar to what you would find on a Voron 2.4 or Trident. An exhaust system works in tandem with an internal…
I'm not a fan of the skirt piece that BTT released for their HBB board, it changes the stock ahestetics and most importantly it's only compatible with Voron 2.4 printers. Why not design one myself? This print replaces your Voron Trident…
Adapted carriage that allows mounting your dragonburner on a pandora gantry MGN9H
Adapted this x axis cable chain in order to fit my Eryone Thinker SE, in direct drive mode. Support 1 has wider holes to fit the carriage, and Support 2 is taller in order to keep the cable chain level I used 17 chain elements for my…
For now only the support arm and the one with BTT MMB supprt has been done, let me know if you need other versions
Update 1 Added a 6x3 magnet version for the carbon container, you will not need the turning tool anymore and instead will need to source 8 to 10 6x3 magnets. Removing the lid can be easily done by using some tweezers inserted into the…
My own 3d model of the Eryone Thinker SE bed (base + glass on top). It can be used as the bed model in Prusa Slicer, and can be paired with one of the provided textures
Wanted a cover for my Weho S-400-24 power supply, which also would allow me to install one or more XT-60 connectors to connect it to my drone battery chargers. Since I didn't find anything matching my needs online I took an existing…
Took the original model and made slight variations to improve its printability. Print as oriented with supports!
Simple mount for the SKRat motherboard, that in conjunction with this PCB din clip allows mounting it to DIN rails, especially for use in the electronics compartment of a Voron 0 3d printer. This mount uses standard voron heatset inserts…
Edit: added a V2 version with a taller pen-holding section which removes wobbles almost completely. Massively improves quality of drawings on my tests. Wanted to try out some pen plotting on my printer running a Hero Me Gen7.2 setup, so I…
Remix of this mount found on thingiverse, but with the filament exit going up instead of down. Refer to the original model for all other info!
Simple modification made to the original model to fit IEC 320 sockets with screw holes on the long side instead of the short one. The back cover has remained unchanged
After looking for an Orange Pi 3 LTS case I stumbled upon the model I remixed. My first print went just fine but I noticed two aspects that could be improved upon: the top case has two separate elements that connect to the main body after…
Very simple change, took the original toolhead board mount and removed the bottom screw point to allow clearing the tap carriage pcb. Also lowered the motor mounting holes to raise the toolhead pcb by 5mm. Works with A4T and WWBMG…
This is a mount for a 2x18650 LiPo case you can buy on aliexpress and can see below. The mount attaches to the elastic straps on the back of the EV800D goggles, behind the soft piece in the center. Here is the final result You need to…
These are my own set of keys which I modeled for my Voron Trident's Bigtreetech HBB macro keypad My personal use for each one is as follows: home all axes maintenance mode (printer lowers bed to the bottom and brings toolhead to the…
Useful adapter to mount a cable chain on the back of a sherpa mini, in my case mounted on a Hero Me Gen7. Check my other model https://www.printables.com/model/201736-drag-chain-cable-chain-eryone-thinker-se-direct-dr to see which drag…
Battery compartment cover that I modeled for my FrSky Taranis X9D+, since the model I remixed it from has sloppy tolerances and I thought I could do a better job. Keeps the original cover aesthetics, has a thumb grip for easy removal, and…
Semplice modello con scritta “Riscatta un buono RYANAIR”. Per stamparlo in multicolor inserire una pausa al layer in cui si vuole cambiare colore e manualmente caricare il filamento nuovo
Simple design for a foot that can be positioned at the junction of a 2040 extrusion and a 2020 one. Attaches using 3 T-Nuts and M4 bolts, original design based on the Eryone Thinker SE, but can be used for any printer that uses 2020+2040…
A simple bell-shaped holder for round sanding paper (116mm)
Updated dragon mount to accommodate the longer meltzone provided by the Mellow v6 pro adapter
Simple holder for soldering tin spools with 56mm length and 63mm diameter
Adjustable version of the SlideSwipe top extrusion mount, quick to print and easy to raise and lower
Updated the original model for use with 2mm acrylic panels
Simple trimming of the SlideSwipe probe carrier piece, which allows using less y axis space for pickup and dropoff. Particularly useful when paired with my SlideSwipe top extrusion mount if you want to mod your voron 0 into a tri-zero
The biggest upgrade made to my 3d printer was to switch from stock hotend+extruder combo to a direct drive v6 setup, using the Eryone Thinker SE Direct Drive mod BMG + E3Dv6 (Including Volcano) project. I was overall satisfied, if it…
Added a cutout to pass a cable from the front right side of a Voron Trident to the electronics bay
After installing the manta ray bed from hex-zero, I noticed that my slideswipe dock that attaches to the y extrusion won't fit anymore. To combat this issue I mirrored the entire assembly to allow mounting it towards the back of the…
My own bltouch mount I designed, as I didn't find any that would properly fit my printer (how does that happen I have no idea). This is technically a remix as I took of the basic dimensions, but at the end I designed everything from…
After swapping the original board of my Eryone Thinker SE with an SKR Mini E3 V3 I found myself in need of mounting it. This model allows placing the new board on the same location of the old board, but removes the ability of reinstalling…
Drag chain end-piece to be screwed to the BMG-M Rear Mount, allowing the use of a drag chain on your printer. I didn't create other variations since to me it is the one that makes the most sense to be used. No heatsets required, just two…
Female version of the 6x3 connector without space for wires, to be used as a simple plug and avoid short circuits
This mount allows you to mount a RunCam Thumb Pro 4k camera on a BetaFPV 95X V3 FPV drone. I personally find that the gummy mounts are too floppy, so I passed an M3 bolt through each one of them and secured it with an M3 locknut, with…
Inclined LCD holder for the one supplied with the Eryone Thinker SE, to be mounted to the front 2020 extrusion. Made after removing the front aluminum plate, it attaches to the LCD screen using the same hardware as before, and attaches to…
I tested out the awesome Cobra Dri by Hemi345, and noticed that I really didn't have the need for a dessiccant beads compartment, so I took it off. Still a cobra, still dries your filament, this time in a stealth fashion! Instructions and…
Remixed version of this design which removes the weird seam on one side, that's all. To improve buoyancy, you could vary the infill density as follows (works on PrusaSlicer and SuperSlicer, but I'm sure it will work on other slicers as…
Added a cutout to pass a cable from the front left side of a Voron Trident to the electronics bay
Remixed gland mounting piece to allow using one with M16 thread
After I installed the new Voron 0.2 tophat on my printer, I noticed that the door cannot be removed easily as with the 0.1 tophat, which had built-in clearance for the pieces. I modified the front bottom left clips of the 0.2 tophat to…
NEW VERSION HERE! https://www.printables.com/model/801506-slideswipe-adjustable-top-extrusion-mount-with-cab When upgrading my Voron 0 to a tri-zero I wanted to keep using my SlideSwipe probe. This meant moving the motor attachment from…
These magnet holders are used in conjunction with a zeropanels door, they work in the same way as the stock Voron 0 door magnet holders, but these are snap-in, use close to no filament, and print lightning fast. Also, since the door…
Modesty mesh with vertical rib for improved stiffness
WARNING You will be working with high voltage electronics which may kill you if you don't know what you are doing! Description Took the stl for the Thinker (non SE) PSU bottom piece and worked from that: added a cutout to fit the switch…
This is a (quite over engineered) filament runout sensor mount to be used together with a bltouch (as it frees the z axis sensor). It fits my particular setup, so check the list below to make sure it works for you! To be able to use my…
This tophat clip has been raised by 7mm in order to accommodate standard heated bed insulations like this one . Simply cut a square and place it between the tophat extrusions and the top acrylic panel
A simple dial indicator holder I made in order to level my Eryone Thinker SE bed more easily. Very useful with the update to marlin 2.0, in which manual mesh bed leveling is introduced. My design doesn't clip to the dial indicator on…
Adapter that allows you to install the Hero Me gen7 system on your Eryone Thinker SE. No heatsets required, just 4 SHCS bolts to attach to the Hero Me base and 2 SHCS bolts to attach the adapter to the gantry
When testing my A4T toolheads on the stealthchanger modular docks I noticed they had a tendency to pivot back. I quickly found the common solution is to use this dock replacement which only adapts the short version and requires a reprint.…
I wanted to mount my filamentalist rewinders in an IKEA Samla drybox, and found the original screw holes finicky since you would need an additional nut for each bolt. So I took the cad and replaced each screw hole with a slot for an…
After years of use, my Dreame L10S ultra lost its vacuum valve (or flap? not sure what's the proper name here) on the back, which I assume is there to help with maintaining a good vacuum while cleaning. For this reason I tried to look…
Since I didn't like the stock bowden extruder mount on my Doron Velta I went on and designed a flying extruder version. This approach uses 3 tension springs to keep the extruder centered, and allow reducing the length of the bowden tube…
Removed fins on the CTR kart, as it's not the easiest thing to clean when supports enter the crevices
I wanted to use the hex-zero bed kinematics, but coming from the Voron 0 tri-zero mod I had the bed cable chain attached to the external part of the frame. This remix merges the hex-zero mount with the tri-zero cable chain anchor point,…
Wanted to secure my Kaser 5G Omni antenna more firmly to its metal mount, so I went ahead and created an adapter to be printed in TPU which adds more optional mounting points and has a sleeve that keeps the antenna more stable. I also…
This skirt piece is used on tri-zero printers to allow mounting a V0 display, with this particular remix also adding support for a round momentary pushbutton and a switch. In my case I used the button as chamber leds toggle, and the…
After slowly loosing all the rubber feet on my Logitech X-230 speakers I noticed something: they wiggle a lot. This is because the bottom part of the speakers is not flat, but has a raised notch on the wall hanging piece. For this reason…
3.8mm taller extruder adapter for the A4T toolhead and XOL carriage, to mount a WWBMG IDGA version
Needed a simple pair of anchors to mount a 15mm diameter pole to a shelf, might as well model everything and make them overengineered. If your printer can bridge 7mm of length then it can print these anchors without issues. BOM 2…
After mounting a 350mm linear rail on my Eryone Thinker SE I noticed that the original x endstop was too far from the rail to be used. Furthermore, after mounting a stealthburner toolhead with ebb36 pcb, I noticed that moving the carriage…
Due to the height of the Eryone Thinker SE, having a simple umbilical is not feasible. After checking out other z chain models I decided to adapt the lower mount from the Voron Switchwire project and design a new upper mount. Designed for…
This model allows you to mount a Logitech C270 webcam on your Eryone Thinker SE X Axis, on top of the motor. Stock Thinker SE is compatible as well, but I also ensured clearances with the stiffening threaded rods I have installed. The…
I didn't like the stock Eryone Thinker SE bed cable, it was floppy and sometimes would catch on the right bed extrusion. I took some time to check online for existing solutions until I found this project . I already have a 10x11 3 hole…
These custom feet are designed for the IKEA HÖVLIG kids teepee tent to improve fabric tension and overall stability, keeping the poles properly spaced and removing their frustrating movement as soon as a kid touches them They allow you to…
Adapter that allows mounting fidget spinners with rattling balls to the main hanger
This project allows you to put all the electronics necessary for a wireless bias lighting system in a compact under desk case, which provides insulation from all electronic parts, airflow, and easy mainteinance. Wiring has entrance and…
Took the original HF right fan duct and integrated holes for SlideSwipe magnets, as well as wire channels. Geometry has been taken from the DragonBurner V8 fan duct that supports the same probe BOM 2 6x3 magnets 2 wires follow the…
Adapted the AirGradient desk stand to allow mounting the DIY version securely. The case Snaps in place. I personally used the version with a cutout for the temp/hum sensor to give better readings
Took the stock Voron skirts and adapted them to fit a V0 display, no tilt angle since it's positioned at the top of a tall printer. Both split and single piece versions available. Skirts mount as the stock Doron Velta ones, the display…
Simple mod, took the original VHB DIN mount of the Voron 0 project and made it 50mm wide, to allow mounting SSR, Wago blocks etc, which wouldn't fit on the stock DIN mount. Make sure the side which will accept the VHB tape (the one with…
The original extruder mount protruded from one corner, and used quite a lot of plastic. My version still uses the same mounting hardware but uses less plastic (and prints faster). You can flip the extruder and bring the bowden tube to the…
![Bigtreetech Smart Filament Sensor [SFS] V2.0 2020 extrusion mount](https://media.printables.com/media/prints/713155/images/5592874_cb9a04ee-213a-4379-8699-e3cd6bdc1202_aa9505aa-392a-4dc5-b6a4-406f33e187a3/photo_5828067761232920630_y.jpg)
