Counting matching models…
The TZ V6 2.0 becomes 1.8mm longer with a V6 nozzle. This offsets the dragon mount back by 1.8mm to make the nozzle position correct again (see pic). This makes it incompatible with the original tiny nozzle it comes with since that is too…
I really liked Scott Yu-Jan's iphone 15 standby mode dock, so I made it fit an iphone 12 with a thin hardshell case. I also modified the airpods charger slot to slot in from the other side, so that the rear of the case can be shorter than…
I love using poker chips to replace currency in a variety of board games, it's a game-changer for ease of transaction, tactility, and speed :) Clay chips are much heavier and satisfying to use compared to any 3d printed chip IMO. I wanted…
Remix of parametric keyhole pin
Also see this reinforced version: https://www.printables.com/model/1543813-reinforced-ebb36-mount-with-protoxtruder-10-20-wit This is a simple EBB36 mount for ProtoXtruder 1.0 and 2.0, or any other extruder with 45 degree mounting offset.…
Credits to NiGauBech for original model :) I wanted to print in PETG for hot environments without damage. However, the keyhole shaped guide rails no longer fit from the original model. This version widens the keyhole rails and still be…
When using the community bottle cutter, I noticed the base was only secured with 2 screws, causing it to flex upwards and have unnecessary strain. This model fixes the issue by adding 2 more mounting holes to the base.
I modified the Idler to support F688Z Bearing from Ender 3, and enlarged the counterweight for better counterweighting :) I also took the soldering iron holder and base from the below two models:…
After finding several hold-backs on the various printer websites, I decided to design my own :) This design is focused on looking elegant, functioning well by closing in on the curtains more, and look like something you might buy at a…
[a]_door_latch_base_x1: Edited the bottom profile to not collide with the panel holders Revised the extrusion insert to allow it to sit flush with the frame when using t-nuts or roll-ins frame_latch_x1: Revised the extrusion insert to…
I made this because the original was mostly looking above the build plate, but I wanted it to look more at the build plate. This is a remix of the other profile mount holder, twists into place on and holds onto the camera firmly. Insert…
I really liked the sleek standby mode docks created for iPhones, but those were often designed to exactly fit the phone and not other sizes. For this design, I opted to create a universal variant that will work for any size of phone,…
I reinforced the mounting holes and structure of the mount, so that there is no EBB36 Wiggle when straining the strain relief. I did this by looking at the PCB components arrangement of the EBB36 1.2 and seeing where I could add more…
This hook latches onto the top panel of a fridge door without affecting the seal of the fridge, so the sizing may be different for your model of fridge! The critical dimensions are: 51.3mm gap between the two “legs” of the fridge, and…
This one requires GX12 4 pin connectors, and really cleans up the umbilical management! rest is self explanatory I hope, the required items are the same as listed in the original github.
This is a simple spoolholder to go inside a homecube or similar 2020 extrusion enclosure. It requires access to the bottom face of a top 2020 extrusion, and requires the side panel to lean against for structural stability. Use T-nuts or…
With this mod, it is now possible to buy a whole Nextruder in pieces without the need for buying a MK3.9 Kit . This mod removes the need for the missing 'Pin 2.9x8.5', 'Tubular spacer 13.2x3.8x0.35', and the 'Spacer 6x3.1x8'. These are…
These are all currently available results.
