Counting matching models…
Designed as a favor to a friend, a more sturdy mount for hands free action with the Norwegian product called “The Handy”. (the original, the new V2 will not fit this) Other designs seem to be too fragile or not rigid enough for the forces…
My take on the wrapper holder/cutter. Designed from bottom up but not my original idea. This one is slimmer and more handy on the rolls i have come across. Being both thinner in diameter and wall thickness its also a bit cheaper to print…
Print standing, bolt onto the side of the kayak. Didn't have a good photo available when i published this, my kayak isn't stored where i live.
The retail Peltor 30mm adapter for KASK plasma helmets had a mounting angle that made it useless. This adapter provides the correct angle to put pressure on the ear to block harmful noise. Dont have a picture of it mounted at the time of…
I printed the FlexRex but felt it could use some more sturdy links that are more child proof. The link type plays better to the strengths of 3d printing rather and will hopefully take more force to come apart. I remade the FlexRex from…
Decorative “raw” concrete candle holder, suitable for both candle sticks and small flat bottomed candles. Reusable mold, make different versions by not filling the mold all the way and vary height. Makes an easier release if you apply a…
Made a simple thing to finish off a belt for my cr10S5 but it should work fine for similar attachment points. CR10 ends are crimped, but these are removable and adjustable. Thread the end of the belt up through the most narrow part with…
Wifey was tired of cheap flyswatter that were short and broke after a short time. Made one to mount on a steel rod/tube that has a large area and has lasted a few years now. Has started to tear at the tip but has survived much longer than…
Bracket to mount a DEFA car heater with a single bolt, e.g. to a steel grid. Fits the DEFA bracket with wood screws and a 8mm bolt in the center hole. I mounted it to a steel grid in the back of my wifes pickup with a 50mm square shim and…
Belt tensioner for cr10s5. Edit on my first design. No longer uses part of the original bracket. This will also fit on any 20x20 profile but check the height of the belt over the profile. A bit more sturdy and easily printable design than…
Attach the sodastream gas bottle to the korny keg to make it more portable and easier to use. Fits straps up to 50mm wide. Take care to avoid damage to the regulator during transport or use. Have fun, Skål! Contact me if you want to make…
Adapter for the ridgid 50mm plastic pipe cutter, for 45mm and 40mm. Fixed for a friend, maybe more would find it useful. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: na Infill: na Filament: na…
Inline filament sensor and cleaner WIP (work in progress) To avoid cluttering in my enclosure i feed filament from another closet section by ptfe tubes. Previously i mounted the filament sensor and a separate cleaner near the filament…
Just a small raspberry clip for steel wire that i made for my bushes. Printed in ASA for longevity. Will snap on to wire with a 45 degree offset for easy access. Category: Outdoor & Garden
Micro SD card can often contain valuable data representing hours of work and driving. Being so small and fragile a container is required, and smaller is not always better. Having almost lost an SD card container in the snow after a day of…
Build for a project where i need to get mud out of very deep holes. Made for a 1\4" BSP fitting for compressed air hose coupling and 40mm PVC pipe. Using low pressure/flow it works as a regular airlift pump.…
cooling fan duct to mount directly on a titan aero with volcano hotend Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0.6 Infill: 20 Filament: any PLA Category: 3D Printer Parts
Fume extractor for 120mm computer fans and 130mm charcoal filter. Use M4 screws for mounting on underside of rail. Wood screws will suffice for attaching the fan and filter. I had to drill out the holes on fan mount for the screws i had…
These are all currently available results.
