Counting matching models…
There's a positive and negative of the pattern, so one stamps the bricks, the other the grout. One gives an outset look, the other makes them look sunken. I made these to stamp oven hardening clay.
Print with 100% infill. If you need more relief to make finishing easier increase the Z height. Prints OK in filament, fantastic in resin.
My GF is keeping me buys designing and creating things for her Fairy Garden. This was one of my first creations, but I'm still happy with it. There's a few choices in file downloads. Files prefaced with “sliced” are sections of the…
The granddaughter is into this game, so I thought I'd recreate the logo as a backpack zipper fob. I imported the logo as an image then manually traced it in Fusion 360. I adjusted the layer heights so you can do manual filament changes…
Pair of eyeglasses for the cricut cutie in three parts. Right Arm, Left Arm and frame. The arms angle in, so there's a left and right. For a really nice fit, I used a hairdryer and lightly heated them, then adjusted the fit. The arms slip…
Each lid needs two clips - a left and a right. The clips are tapered for better fit. There's two sizes - the difference is the depth. Small (SM) fits most lids. Large (LG) is for thicker lids. Apply 2-sided foam tape to the rear of the…
I needed a way to hang my phones under my desk - I wear them gaming, but there in the way the rest of the time. There's no room on my desk for a stand. It's designed to attach with a flat screw or a screw and a small washer. No supports…
GF: “I need you to make me a Quilling tool - do you have any small wooden dowels?” Me: @#% is a Quilling Tool?" Well, it's for making paper flowers. So I designed and made this version. It pops on the top of a pencil. There's two…
Can be scaled as small as 4" and still print well. For a nice, clean finish I suggest putting the “outside” against the bed. The photo of the actual print was the original - I noticed some lines did not print correctly and repaired the…
I made this for the GF's fairy garden. Originally to cover a well she made from clay, but it's handy for all sorts of things. It can be stretched along the long axis, scaled, etc.for a variety of uses. The top edges are chamfered at 45…
For the best surface, flip it so the outside in facing the bed. Can be scaled to as small as 6". Scanned and cleaned up from some clipart I put together 30 years ago.
There's three models here. The beam, the support/base and a connecting plate. The beam slides into the base - glues in place with CA or epoxy. The plate is designed to glue wherever beams met for a look of a bolter support. I've scaled…
I needed a way to display a Stargate I download and printed. So I made these circular stairs with platform. There's a slot in the back the gate slides into. I damaged and aged mine before painting.
I needed an obelisk as a prop so designed this. It's based on a traditional Egyptian obelisk, but is smooth on all sides. There's two versions - flat and upright. I made the flat in case you have difficulties printing tall models. You'll…
The tip on my blower is a bit big for many uses, so I made this venturi tip. Has 2mm ports leading from the tip backwards. Slides over soft tip of blower, be cautious not to block the ports. Opening is 13mm, can be scaled in your slicer…
Slips over the soft nozzle on standard small blowers. Can be scaled for larger tips. Concentrates the air to a 4mm stream. Can be printed without supports - I made it with pretty steep angles. Rotate so the base is down. You may need a…
I have dozens of these clamps. I lose faces. Faces wear out. I needed another use for TPU. So here's a quick-grip bar clamp replacement face. There's two versions: Pair of faces: Pair, upright. They act as supports for each other. They…
A relative has to carry an Inogen portable concentrator everywhere. The cannula hose keeps kinking where it attaches to the device - so I made this. It's a simple support that slips over the base of the cannula fitting. It's held in place…
There's three versions of the same model. Solid Model - to print on vase/spiral mode. Shell Model - has 2mm thick walls. Great pencil holder. Use several walls or 100% infill. Semi-Solid - has a circular hollow section. I used 15% infill.
Three simple filament clips. The filament threads through the eyes and the face tucks between the spool and filament. Print some for fun or to rank your filament: Amazing! Like it! Sucks! The more flexible the material the better. I…
Classic carpenter's sawhorse, the type we all made in woodworking class or on the job. Tool tray near middle. There's two files - half the horse and a connecting piece. Print two halves and glue together using the "board" to connect and…
There's one bracket in the file - print two of them, one for the front the other for the back. Screw one in, slide in the brick. Slide on the other bracket, screw in. You can also use 2-sided foam tape, etc. 50% infill, standard PLA. I…
I have a Fluke ST120 / ST120+ and want to protect the face from getting messed up in the toolbox. Printed in PLA with supports (big overhang), it simply pops on and of. To remove it just pinch the angled end and case together. There's a…
I have a few accessories that use these batteries, but I hate leaving them in there during storage. Just tossing them in the box can be a problem with shorting. So I made these simple caps. They fit snug enough not to fall off. If there's…
Printed in clear TPU, keeps the lens dust and print free. For 77mm lens, in the center is an extra support ring that's 4mm deep and 50mm across.
The teflon (or plastic?) roller wheel on the arm wore down - and the arm kept dropping out of the track. The windows are 20 years old and no parts are available.So I cut off the worn plastic and measured the parts. There was a stem on the…
I have a pretty free-spinning spool and with the constant retraction, advance, retraction, etc. I can wind up with several loose windings on the spool. Occasionally one can jump over the edge. I made this arm to prevent this. It clamps on…
I have both models of the Feiyu Pocket 2. While I'm using them I often have to put them down, put in a pocket, etc. I usually have it mounted to a handle with a light and a Zoom mic, and putting it in the case is a pain. So - simple…
Scales up or down nicely. Printed in “fuzzy” mode to match the textured exterior. Inside is hollow, base is solid, top has an area to put in some small stones, glass, etc. or fill with something to resemble fire. The photos are a 50mm…
I love this brewer, but it vibrates when making coffee. This causes any mug with a narrow base to slide across the support shelf. While it can't fall off (there's a lip) it does cause the dripping coffee to eventually miss the cup. I…
I make a lot of stuff with these bearings, but getting the holders just right can be a pain. So I made this. I print at 40mm and 100% infill. Slow speed=accuracy. It will be a little big - the bearing drops in and can be held in place…
We needed a way to store 24" rolls of vinyl that did not take up too much room. We have slatwall in our storage area - so I put two glass shelf brackets up high and rest the vinyl on these. I made these to go on the ends and prevent the…
These are all currently available results.
