Counting matching models…
I have designed this bracket to fit on the back of the Celestron Nexstar 6SE, to allow for a dovetail to be mounted on the back of the telescope. This allows for a guidescope or any other scope with a dovetail hotshoe. I printed this in:…
This is a temporary replacement cap for the brake fluid reservoir on a Mitsubishi Pajero 4th generation (Montero/Shogun). I suspect this would work for other Mitsubishi cars. I have made this out of ASA, however I believe that brake fluid…
I have just reposted this from Thingiverse. This is a Bahtinov mask for the Svbony 503 80ED refractor telescope Printed with: 20% infill PLA+ no supports Thank you to the original maker.
Replacement leg for the Rummikub rack Print standing up, so it doesn't require supports 0.2mm layer height PLA+ 100% infill
This is a handy holder for the WolfBox MF200 air duster. The model comes with 3.5mm screw holes to attach the holder to a shelf/workbench so that you can store the air duster out of the way Printed with 20% infill, PLA, 0.2 layer height.…
This is a holder/frame for a Baader Solar Film filter, that will fit a Svbony SV803 80ED Telescope. It comes complete with the clips that will hold the retainer and bracket togeter. Printed with: 15% infill 0.4mm layer height PLA+ No…
I needed a single row egg tray for my fridge but couldn't find a model already made, so here it is. It measures 50mm wide x 280mm long and can fit 6x large eggs. I have split the design in half, so that it can print on my Ender 3S1 which…
This toggle is incredibly light and simple, yet very effective when needing to tension and secure a tarp ridgeline around a tree. With this toggle, you will not need to tie off any knots in the ridgeline and can be quickly and securely be…
This is the square blanking plate for the center console of the Mitsubishi Pajero/Montero 4th generation, with a pre-drilled hole to allow a cable to come through from the inside (up to 5mm in diameter) I printed the plate in PLA+ and…
20mm diameter workbench dog hole plug. I have added a 15mm diameter hole in the middle, to allow for a neodymium magnet to be glued on the inside. This allows for an easy way to remove the plug from the top, with the supplied plug puller…
This is a Holy Grail model based off a timber version that I have created. It would look best if printed with a timber-looking filament or painted accordingly The current size is approx 60x60mm and 70mm tall, but can be scaled as…
I needed a castor wheel for a Stiga Ping Pong table, I couldn't find one so I created one. The wheel itself is 41mm in diameter. The size of the hole where the pinion goes in to the casing is 8mm in diameter. I printed it in eASA as the…
This is a replacement cover for the clutch pedal of the Nissan Navara/Frontier D22 (2009) After many years of use, the original pedal cover broke/split This print requires a flexible filament, I used TPU but there might be other flexible…
The original pedestal of this tower fan broke after many years of use. Instead of throwing the fan away, I decided to make a new stand. The design is different from the original one (the original has a round base) and I had to make it…
These rings/retainers allow a Baader solar film to be used with the Svbony SV47 8x42 binoculars Printed with: 15% infill PLA+ 0.4mm layer height no supports required You can just cut the Baader film accordingly and jam between the two…
This is a handy holder for the WolfBox MF50 air duster. The model comes with 3.5mm screw holes to attach the holder to a shelf/workbench so that you can store the air duster out of the way. I printed it with 20% infill, 0.2 layer height.…
Jig for grinding the primary bevel of a knife. One side has a 3 degree angle, the other side a 4 degree angle. Recommended to print in ASA or ABS, which are more heat resistant. 40% Infill 0.2mm Layer height
A simple, Small stand/holder for 4x C245 soldering tips and a roll of solder. Can be printed with 10% infill 0.2mm layer or coarser if you wish PLA/PLA+ or PETG
This is a helmet hook to suit the Honda XSR900GP, to attached the helmet under the seat cover. Intended for internal use only. I recommend the following: print in ABS or ASA, for thermal/environmental resistance print in the orientation…
These are all currently available results.
