Counting matching models…
There are two different solutions here, a geared solution and a belted solution The gear solution worked well for me originally but turns out my motor wasn't fully concentric so the gears would fail to mesh and lose encoder steps causing…
This is a reverse engineering of a product by www.pannierhooks.com, given I don't live in the USA this would have been quite costly to get it imported and an unpleasant experience overall, I have used this with PLA+ and it has been very…
Uses 2x M3x40mm 2x M3x6mm 2x M3 nuts
Print 2x hooks and a pair of the pegs and attach to the peg board, you can get better DualSense support if you swap the arms around (see pic) These come orientated for strength, the originals broke on me over time Uses hook from:…
Attach a chronograph straight to your RIFAttach a chronograph straight to your RIF printed at 0.2 height, 4 walls, 15% infill
If you are getting a lot of frame hits because you suck at tying bands to the forks like me, you would probably want a set of band clamps, you can buy some official ones from wasp slingshots but if you want to print some here it is, print…
REMIX OF https://www.thingiverse.com/thing:1060861 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Yes Supports: No Resolution: 200 Infill: 10 Filament: TINMORRY PETG C-Transparent Notes: PLA also works, the original was…
This will allow you to insert the pulley deeper into the shaft as for me it was too short and caused the pulley to pull out after a while Also your belt will be straighter
Here is a replacement part for your Weinmann brakes, if you have the ones that have barrel adjusters then you can find those on thingiverse as well, these should just slot in as they are same dimensions as the originals, I think the…
I got tired from the magnets falling out, gluing them down sucks since the glue can spill out and mess with the conductivity or flatness of the mating surface I got a KlickyPCB kit and with it came these countersunk screw down magnets and…
Needed to join together some springs I cut too short. Slip on the spring ends and then add a bit of super glue so it doesn't come apart. smallest layer height you can for max strength. 100% infill Category: Sport & Outdoors
Print with nut cavity facing out, the bolt head diameter should be under 12.95mm on the flats to fit, scale accordingly
EDIT 27/6/2021 Okay, it is time to actually go ahead and finish this design, I looked around thingiverse for better design inspiration, I found a design but had to design it in CAD by myself, 3 pieces now, you will need: -Super Glue -M5…
If you want to add rumble motors to use with ShakeIt on Simhub and you've built your own metal pedals from DIY Sim Studio then you've come to the right place. Clutch, Brake and Accelerator Pedals are supported with a single design, if you…
I'd recommend supports when printing, 0.2mm structural, PETG as been fine for me. Instructions are from https://help.prusa3d.com/guide/4-heatbed-upgrade_1110680#1117086 If you built your core one then you'd have a spare bed expansion…
Lens template for the protector NOTE : template covers only the original protector, chances are your lens will need to be a bit longer, for example I need about 3.30mm extra length so the total length would be 27mm Category: Sport &…
Print in PETG, I suggest at least 4 Walls -M5x20 x 2 - I used a round head with a hex pattern, may need longer ones depending on your setup -M5 nut x 2 (locknuts recommended) Print 2x of each, the 3mf is oriented properly already
Inspired by Remade for C4 Cartridges, Tr 25x3 Included FreeCAD files, use the .step in your slicer, slice with the top of the cap facing down, since the threads have 3mm pitch, 0.2mm is fine for layer height.
fixed screw hole length issue, added side to side movement, cut out for linear rail
I've printed this with the default 0.2mm Speed TPU profile on my CORE one I'd recommend 5% infill because 15% was too stiff but still worked on my car (no idea if I'll be able to take it off)
Combine the sideswipe probe with a nozzle brush, use a single servo for two functions, no build volume loss (I've ensured that the brush does not collide with the printhead) You will want to print this with supports, with the bolt head…
EDIT: I've moved to the SideSwipe probe for the dragonburner, I got fed up with the PZ probe, I don't think it is worth your time Assemble like in the photos, You will need a Form A M6 Brass washer I ended up ordering multiple ones from…
A screw post to mate the Pedals to the pedal plate Designed for M6 Bolts, M6x25 preferred Print two Just import the step into your slicer and accept the default conversion settings
These are all currently available results.
