P
PrintablesVlad_kzmnk
Candy bowl
Another bowl for candies or something else. No supports required.
Print approx. €3.37–€4.12 excl. taxPreliminary estimate for one variant
- Downloads
- 644
- Likes
- 85
- Rating
- 4.83
All models
Counting matching models…
P
PrintablesVlad_kzmnk
Container for spices
Container for spices
Print approx. €3.53–€4.31 excl. taxPreliminary estimate for one variant
- Downloads
- 35
- Likes
- 3
- Rating
- 0
P
PrintablesVlad_kzmnk
Desk organizer
Model was printed with 100% infill and supports. Care required when removing supports.
Print approx. €3.77–€4.61 excl. taxPreliminary estimate for one variant
- Downloads
- 25
- Likes
- 4
- Rating
- 0
P
PrintablesVlad_kzmnk
Cutting board rack/drainer
Cutting board rack/drainer Made with angle guide under to install it onto square kind of kitchen sinks. Print in vertical position without supports:
- Downloads
- 216
- Likes
- 185
- Rating
- 0
P
PrintablesVlad_kzmnk
Luxe petal fruit bowl
Two models - one with thick walls, another for vase mode.
- Downloads
- 181
- Likes
- 29
- Rating
- 5
P
PrintablesVlad_kzmnk
Insertable hinge
Guides added to make it insertable for another project. Print on flat surface.
- Downloads
- 54
- Likes
- 3
- Rating
- 0
P
PrintablesVlad_kzmnk
Military buddy in body armor
Some supports may be required.
- Downloads
- 45
- Likes
- 11
- Rating
- 5
P
PrintablesVlad_kzmnk
Budget SKADIS pegboard organizers (vase mode)
Budget organizing containers with holder clips. Container - print in vase mode. Printed with 0.28mm layer height. Holder - print in vase mode, but set the value “Bottom solid layers” to 0 (zero) to make it through. After printing insert…
- Downloads
- 40
- Likes
- 11
- Rating
- 5
P
PrintablesVlad_kzmnk
Adjustable display stand (With platform on ball joints)
The whole model consist of few parts: Lower platform Upper platform Lower tower (Print in vertical position) Rotating wheel Upper tower (Print in vertical position, increase brim) Ball joint Ball joint nut. Holding clips for exhibition…
- Downloads
- 40
- Likes
- 18
- Rating
- 0
P
PrintablesVlad_kzmnk
Hercules DJControl Mix stand on ball joints
Update 12.02.2025: reinforced main arm added (phone holder) Update 26.02.2025: Basket holder - thread length increased Update 27.02.2025: Dual-joint variant added. Much more rigid: Update 02.03.2025: Dual joint base - reuploaded with more…
- Downloads
- 34
- Likes
- 30
- Rating
- 0
P
PrintablesVlad_kzmnk
Neck holder DJ61-60114A for Samsung SC4142 vacuum cleaner
Neck holder DJ61-60114A for Samsung SC4142 vacuum cleaner and holding clip. Internal infill for the clip was made 100% to increase strength.
- Downloads
- 25
- Likes
- 4
- Rating
- 0
P
PrintablesVlad_kzmnk
Redirected and reinforced base, printable pipes
Redirected and reinforced base for bigger adhesion + printable pipes.
- Downloads
- 25
- Likes
- 0
- Rating
- 5
P
PrintablesVlad_kzmnk
Watering can (extendable nose)
Main body better to print with 100% infill to increase compensation weight. There is also model with wider handle if you like to increase weight even more (in that case print appropriate stand also) Small support for main body nose may be…
- Downloads
- 20
- Likes
- 3
- Rating
- 0
P
PrintablesVlad_kzmnk
DJControl Mix case (Ver. 1)
Model consists of several parts: Lower case part Upper case part Insertable hinges (3 pcs) - download from here https://www.printables.com/model/1182163-insertable-hinge Insert hinges firmly to appropriate guides at the back of case parts…
- Downloads
- 16
- Likes
- 8
- Rating
- 0
P
PrintablesVlad_kzmnk
Overhang weaving vase/holder/cup
Test model. Print settings (nozzle 0.4mm, PETG): Vase mode Layer height - 0.28mm Outer wall (Line width) - 0.8mm Detect overhang walls (Overhangs) - disable Filament settings (PETG): Print temperature (for all layers) - 260 C Cooling (for…
- Downloads
- 10
- Likes
- 2
- Rating
- 0
These are all currently available results.