Counting matching models…
This is a simple test for your manual or auto bed leveling. How to use it: Level your bed with the screws. I'd advice you to find a level as low as possible as the springs are stiffer when compressed and the bed is not loosing the level…
A simple DIN rail mount for the Raspberry. You need 4x M2.5 screws to mount the Raspberry.
This is a cable channel for the Enderwire conversion. It's mounted with M3x8 screws to the frame. You can use the zip tie points to hold some cables down. Feel free to break off some of the studs in the center if they are in your way :)…
The slider mechanism of the original Nevermore v6 did not work at all for me and I gave up after some attempts. I still wanted to open the cartridge tool-less, so the original mod didn't quite work for me either. That's why I made this…
I build the Lack enclosure for my Ender 3 Pro but the cable of the heated bed constantly was bended in weird was at the back panel because a couple of centimeters were missing. My solution is a cable strain relief replacing the original…
A simple case for a Raspberry Pi and the Sonoff ZBdongle-E, not ZBdongle-P! Pay attention, they are almost the same dimensions and look the same. I think all -E models have the label “Zigbee 2.0 USB Dongle Plus ” on them while the -P…
This is a dummy battery for Sony NP-F batteries. It can be powered by a USB PD (Power Delivery) power supply. Usually those come with any laptop using USB-C to charge and most smartphone's fast chargers will work as well. You need: 2x M2…
This is a simple part which allows you to connect a vacuum cleaner to your multitool when using the sanding pad. This part covers the holes of the pad and allows the vacuum cleaner to suck the dust in. I used it so far only to sand down a…
This allows you to extend the cables directly at the bed and replaces the cable chain mount. Use a dap of super glue to hold the Wago and JST in place. The heated inserts to connect the hook need to be below flush! Bottom them out ~2mm…
This adapter allows to attach a hose with 31.5mm inner diameter to the Gas 12v. Use zip ties to fix the hose. I use it to suck air from vacuum bags. Attaches just like the original items to the front of the Gas 12v. Mine is a little…
Two things included: 1:1 clone of the IKEA ALFTA hook Custom version for the RIBBA picture frame with the deep hooks on the back. Some RIBBA frames work with the original IKEA hook, but some need this one because the hook doesn't reach…
A custom cover I made for my Enderwire mod, but can be used for any application of the LS350. Be aware that there seem to be versions with 24V and 12V fans out there. POWER SUPPLIES ARE VERY DANGEROUS EVEN WHEN NOT CONNECTED TO POWER FOR…
To assemble you need: 2x Buck converter 6x M3x4 counter sunk screws 2x JST PH 2 pin housing 1x JST PH 3 pin housing Cables and solder equipment I found that the mount slides on the DIN rail, this most likely is because I used ABS to…
This is a simple Y-splitter based on the Bowden adapter for Stealthburner. It's completely compatible with toolhead mainboard etc. Use two ECAS04 to secure the Bowden tube, besides this it's all the same as the original single Bowden.
A simple comb to clean out the filter! Category: Hand Tools
A stronger version of CSD Salzburg's 45mm hook Category: Organization
A simple mount to arrest a PG7 connector to your frame, use with 2020 extrusions
Please read carefully before building the stand! All pictures shown are v1, I did not print and build the current v2 but all adjustments where tested virtually. About the Stand I moved my VESA display stand to my Living room and needed a…
This is a LED channel that can be mounted on the bottom panel of the Switchwire (Enderwire). You need a transparent bottom panel of course. Use the “template” to drill the holes into the bottom panel! There is a small gap where the two…
Similar to the original but works with generic LED strips instead of the custom PCB. The strips can be up to 14mm wide and is slid in from the back, similar to the diffusor. To mount, choose one of the clips from the original and glue…
Same as the E3CNC RODMOD but with zero backlash nuts, similar to the Milo CNC.
Made for “USB camera modules” you find on Aliexpress with a 29mm hole pattern. There are a lot! I assemble and configure everything in this stream:
This is a mount for the M4P in the Switchwire. It's REALLY tight. You need 90º USB adapters to use the USB ports on the M4P, but this blocks the Ethernet port. Installation: I also added a mount for an 8010 fan to cool the steppers, this…
The Tush with the lock for the Lack case. Print one of the part here and 3 of the originals from here: https://www.thingiverse.com/thing:2047554 One part of the spool holder then locks into place with the lock of the case:…
A bits holder for the Bauhaus tray. Uses 6x3 magnets to hold the bits in place
This adapter allows you to stack two IKEA Korken jars (0.5l) or IKEA Korken jars (1l) . Other sizes have different rounding and will not fit! I waned to stack two of those in a drawer but they always fell over. This stacking adapter fixes…
Another take to mount the IKEA Dioder bars to an Ender 3. The holders slide in from the side into the 2020 V-Slot Extrusion. You'll need to print two of course. It's a quite tight fit by design so it doesn't wiggle around, you can…
This is a replacement for the motor panel of the Voron 0 with a mount for 2x WAGO 221 and a Fysect UCAN board. You can use two zip ties to hold the bowden and umbilical cable in place and a second one to fix the umbilical to the part…
Cover for the battery plug of the Lekker Bikes Amsterdam+, most likely compatible with a wide range of Bafang batteries. When left outside without the battery the plug fills with rain water, not ideal. The cover prevents water from…
This is a very slight tweak of the original that only prevents multiple capsules from sliding out at once and I shortened the middle track to make it printable with my smaller machine. All the rest is the same. Use the other parts from…
This is my enclosure and electronic box. No manual, please only build this if you are sure the Fusion files are enough for you. The acrylic glass is 3mm and bend using the jig in the Fusion and a hot air gun. Scale the enclosure to your…
This is a generic case I use for ESPHome projects. The case is magnetic and can stick to metal surfaces. A JST-PH 6 pin plug is used to provide power and connect external stuff. You need 8 6x3mm magnets If you download the Fusion file you…
A tray for 6 PicoFinish screw drivers from Wiha. 3x 2.6mm, 2x 3.1mm, 1x 4mm. Uses 6x3 magnets to hold the screw drivers in place
This replaces one of the standard shelves in the Enhet upper cabinet. The main benefit is that the spools don't roll out (if you store without a bag) and that you gain some additional space in front. This allows to mount a honeycomb…
These are all currently available results.
