Counting matching models…
Strong cable hooks/holders/organizer for wide cables. I am using it with 12mm cables (as in photo). I've printed this using PETG, with 6 wall loops and 6 top/bottom layers, infill gyroid 20%. It's very strong. There are three…
It's a box for Router Table Insert Rings (Kreg) . Those router rings are great, but I needed also box for them. This is very simple box, nothing fancy, but it works. Single box can hold up to 10 rings, I printed two of them using PETG.…
YASPO: Yet Another Small (and smaller) Parts Organizer. Another version of the Small Parts Organizer . Why another one? Just because ;) I needed a version tailored exactly to my needs, and I’m sharing it here in case someone else might…
Simple containers but with size that fits to the game box. Don't need to put blocks directly to the table, just get containers out of the box. Easier to store in box, easier to play. You need 6 higher and 3 lower pieces. I printed them…
Simple painter's triangle hanger. Put two screws (template included), hang the hanger, put triangle on top. Voila! :) My printer settings: PETG 0.24mm layer 3 walls 15% gyroid infill
Very simple holder/hanger for Limit Marking Gauge ( MGB 200 or MGB 300 ). Use with 4mm screws.
Very simple holder/hanger for Limit adjustable precision square ( 100x70 or 150x70 ). You can print bigger one for both squares, works fine, but it's a bit too loose for me ;) Use with 4mm screws. Printed with 4 walls, 3 top shell layers,…
Simple hanger for Milescraft TriGrips pads. Put two screws (template included), hang the hanger, put TriGrips on top. Voila! :) My print settings: PETG 0.24mm layer 3 walls 15% gyroid infill supports: enabled
Clip for the Olight I3T EOS flashlight. The original was made of metal; here is a replacement you can print yourself. Designed in two parts for durability. Both parts should be printed in landscape orientation, as shown in the attached…
Dispenser for Amazon Lens Cleaning Wipes. Bootom part (foot) should be glued to the base - thanks to this foot it's much easier to pull wipes from dispenser (there is a place for a finger below). My printer settings: PETG 0.24 layer 3…
Simple holder for LeanCraft KIDO-6A. Unusual shape of tool requires unusual solutions ;)
Gridfinity bin for Tajima 3m tape measure, stackable. Width, length: 84mm Height: 47mm
Diffuser for the Olight I3T EOS flashlight. Durable, diffuses light well. Allows you to mount the flashlight on the diffuser or in the reverse position (using a separate design: Olight I3T EOS stand ). Requires transparent filament (PETG…
Olight I3T EOS Flashlight stand. It allows you to position the flashlight vertically so it shines upward. You can also use another one of my designs, the Olight I3T EOS diffuser , to position the flashlight upside down :) Small, handy,…
Simple holder for Milescraft Cabinetmate. Size of pins is adjusted to fit into holes of Cabinetmate AND get down a bit. It holdes a tool and protect against slipping off the holder. And yes, on photo there is mistake in holder…
Gridfinity bin for Amazon Basic Care Lens Cleaning Wipes. 3x1, 75mm tall. My print settings: PETG 0.24mm layer 3 walls 15% gyroid infill
Diffuser for the Olight S2 Baton flashlight. Durable, diffuses light well. Allows you to mount the flashlight on the diffuser or in the reverse position. Requires transparent filament (PETG or PLA). When using regular filament with a low…
Gridfinity bin for Tajima 3m tape measure. Non-stackable, but minimalized horizontal space.
These are all currently available results.
