Counting matching models…
! New second version with more easy assemblage and better look ! This stand is designed to bring the display of a Laptop in a more ergonomic higher position and can be used as stand for Tablets. The angle of the stand is adjustable by…
A stand for HotWheels that position the boxed HotWheels card on a raised height to make it possible to read the text at the bottom of the card. It additionally allows to make better pictures of the HotWheels model by bringing it to a…
A remix of the the Conqueco stand from Stromi56. A Stand for Conqueco espresso machines that is compatible with 2nd-generation Conqueco models. The legs fit securely and snugly without the need for glue. They are easy to attach by gently…
This holder stores up to nine Copic Ciao and Posca PC-3M pens or pens with similar sizes like Edding 400. The idea is to presort a set of pens and colors from the big storage which are actually needed for the current art project. Keeping…
An Arduino Uno Adafruit Motorshield (v2.3) case in the design of a motorsport EMU (Engine Management Unit) for my racing simulation aluminium extrusion rig. There are two variants, one for the 80mm aluminium extrusion width and one for…
This stand holds an IPhone 16 Pro in place and charging it meanwhile by an Apple Magsafe charger. The base is weighted by steel washers and allows one hand handling by tipping the phone on top or bottom to remove it from the charger. It…
A funnel designed for the Sage/ Breville 54mm diameter portafilter. It allows grinding coffee directly into the portafilter without spilling it. A distributer and a tamper fits in the tunnel of the funnel from the top. It is still…
A bracket that provides a proper fixture of the Chiclew Scooter bag to a VMAX New VX2 (Hub/Gear). Tighten the screws only until the bracket is properly seated. A gap between the clamp and the slider parts is intentional and part of the…
The espresso collector cup for Sage 54mm diameter portafilter allows a clean way to fill the portafilter without distributing coffee where it should not be! The flexibel lid is used to grind coffee in front to accellarate coffee…
A plate that covers the speakers from scratching at the bottom and allowing a secure placing on the TV board by preventing unwanted movements due the higher friction of the rubber feets. I did not want to drill holes into my freshly built…
Feets / legs for Ikea Besta corpus with a height of 10cm. One feet needs one hexagonal M8 bolt in length of 40mm for mounting. Mounting of the foot: Hold the foot upside down, so that the hexagonal hole show to to top. Insert the M8 bolt,…
The geometry of my results of measurements of the VMAX New VX2 (Gear/Hub) steering strut. It allows to design own parts in CAD for the E-Scooter such as brackets for bags or locks If you have any comments, suggestions or similar, you are…
New version V2.0 available: This stand is designed to bring the monitor of a Laptop in a higher position to bring it in an ergonomic height. It is adjustable in angle and therfore it allows to affect the height and react to Laptops with…
My two cases for the WMF Nomad cutlery/ silverware broke and I like them a lot. So I decided to develop a case as replacement. Both parts are designed to be printed without support. After printing, a superglue is mandatory to glue the two…
A cover for Spectrum Noir Marker Storage Trays that makes additional space above usable and keeps the tray free from dust. There are two variants, one solid one and one that uses less material (Lite). I used a non three dimensional infill…
A tool for the Sodastream Crystal that loosen the bolt which fixtures the container and allows a more easy cleaning process of the container. If you have any comments, suggestions or similar, you are welcome to contact me.
A remix of the already remixed cap for "The Ultimate Cereal Container Filament Drybox" , which replaced the original T-handle with a round knob. My remix further improves printability for very flexible filaments by increasing the diameter…
Feets for the Western Digital (WD) My Cloud EX2 Network Attached System. My original rubber feet got lost over time and they are very important for the cooling of the device by allowing air flow from the bottom to the top. Therefore I…
Rumbler for the Fanatec CSL Pedals Tuning Kit. Can be combined with my "Arduino Uno Adafruit Motorshield case" to build up a whole working system. Partlist For mounting the rumbler unit to the pedal, the pedal's screw and nut is to be…
On my research and several tries of getting a satisfying feeling and feedback of the Fanatec's CSL Load Cell I ended up with that solution. I was missing the feeling of the pressure point of a real brake of a car and this one comes very…
I encourage you to get creative and design your own cardboard covers for the 3D printed frame using the templates and finish it to a full own customized stand for your Spinning Tops to place it in a showcase. Build advice and preparation…
These are all currently available results.
