Counting matching models…
Use this to prevent damage to your Creality K2 Plus extruder's bowden connector, which may fail if the PTFE tube becomes loose from the cable chain and starts wobbling tearing itself out, damaging the connector teeth. Note: If you already…
This is a narrower bowden tube clip to hold the PTFE tube on top of the cable chain so that it doesn't touch the glass. The original factory K2 Plus clips tend to release and slip off the chain after a while, and misplacing them limits…
This ventilation system was designed with the following priorities in mind: - space saving, you only need about 7cm of space behind the machine - don't interfere with poop chutes which respect airflow, I chose shay's variant also because…
This is a wall mount for Guition ESP32-S3-4848S040 ESP32-S3 based touch screen, which can be purchased without the relay base. The relay base doesn't fit in a standard 60mm diameter appliance wall box, so if one doesn't really need the…
This add-on improves the filament retraction of the spool in Creality CFS, by eliminating the friction between the factory bumpers and the spool, which can become problematic as spools get lighter with less filament on them. Also no more…
K2 Plus's built-in camera is pretty good, but the internal light coming from the rear right side of the printer creates a refraction in the lens which can be seen as an undesired haze on the picture. See the before and after pictures. Use…
Use this to prevent damage to your Creality K2 Plus extruder's bowden connector, which may fail if the PTFE tube becomes loose from the cable chain and starts wobbling tearing itself out, damaging the connector teeth. Note: If you already…
The fantastic Bohr-models of all the known atoms to date, with spinning electron paths, updated for color in-place printing. Updated renders with the following features: - flattened the rings so they have the same height (increased by 1),…
This is a low profile bracket/baffle for a Broadcom BCM5719-4P - 4 x 1GbE PCIe NIC (for example the BCM95719A1904G) to be used in a Lenovo ThinkCentre M920q tiny PC. Remove the card's original bracket and use a small-head screw from the…
This 2.5" HDD/SSD holder was designed to be used in HP ProDesk 400 G4 tiny PCs, in such a way that the drive's SATA connector is inline with the socket for this adaptor cable: https://www.aliexpress.com/item/1005006849197833.html Also…
The heat bed levelling adjustment screws on Creality K2 Plus are pretty small and hard to grip, and very painful to turn, especially if the screws are particularly tight. This is a knob tool to make the task much easier, without having to…
This adapter allows an Ethernet port to be mounted in the Flex IO slot originally used for an extra display output. This was designed for a ProDesk/EliteDesk G4, but it may fit other generations of HP mini PCs. The adapter is designed for…
I made this hood for Hikvision camera DS-2CD2T47G1-L with 6mm and 2.8mm focal lengths to prevent sunlight to burn into the picture when sun is rising, with camera looking to East. No supports needed. Use some UV-resistant material…
Tight wall-mount for various 75mm piping, for example: - plastic drain piping - heat recovery ventilation flexible piping First insert the M3 nuts into the base (use a pliers to snap in), and attach the base to the wall with two wall…
This stand is intended to place four HP ProDesk 400 G4 tiny PCs vertically. Two aspects differentiate it from other similar stands: - small stop blocks at the front and the back of the PC, to not have to hold it by hand against when you…
This is a minimalist tray to be placed in the center console of the Tesla Model Y Juniper (2025), to hold a pair of sunglasses and four S3XY buttons under the lid, so while still accessible, they remain invisible from outside. It was…
A pair of pretty small, but extra strong wheelchocks to be used with 19" wheels in emergency situations. Pack these up with the (scissors-type) car jack lifting kit you take in your car along with the spare wheel. Use the wheelchocks on…
This is a cover for the PTC connector of Nissan Leaf 2013-2023 (AZE0, ZE1) batteries when re-used as stationary energy storage. This part will cover the HIGH VOLTAGE terminals which are not used in such a case. Improved version with…
This is a holder console for S3XY buttons to be hidden behind the bottom of screen in a Model Y or a Model 3. It's a tight fit for the buttons to ensure they never fall off. Attach with double-sided adhesive tape along the entire length.…
ESP32-EVSE is an exceptionally well thought-out diy EV charger (charge controller). This is a PCB mount to attach the esp32s2-evse-d-a board to a standard DIN rail. Use M3 screw insets to firmly attach to the board.
Use this mount to firmly attach the IKEA LÄMPLIG (003.098.29) chopping board to a wall or side of a cabinet. Use six wooden screws. The holders keep the board 10mm away from the wall so you can put back the board even if it's still wet,…
This is a dust and water spill protection cover for the data connector of of Nissan Leaf 2011-2023 batteries. It slides on top of the connector, and uses two cable glands (a PG9 and a PG13.5) to access separately the CAN and a contactor…
Banner makes very good and durable replacement batteries for most car types, but their top is shaped a little differently from how the factory battery is in Toyota. There's a 13mm wide, and 22mm tall gap between the edges and the fixation…
Accessories to mount an ESP32‐S2-EVSE-DIY-ALPHA board, RCM, CTs, contactor, and surge protector into a Tesla Wall Connector GEN2 box. In case the factory electronics are faulty, this can revive in an open source form! Parametric in…
If your Scheppach DP60 Bench Drill (usually sold in Aldi shops) suddenly stops working, it's very likely that the motor speed controller blowed inside of it. By factory this module is not repairable (and of course no spare part available)…
The Dalap 3163 vent air deflector inlet (see https://dalap.eu/distribution-elements/164-2971-pvc-disc-valves manufacturer site) is designed for pipes with internal diameter of 80mm, however, many heat recovery ventilation systems use…
This is fixation ring for the data connector of Nissan Leaf 2011-2023 batteries. It slides in the knot at the base of the socket. Use it to prevent the socket to fall into the battery - this can occur when the workers who originally…
This Type2 plug holder was designed with the following things in mind: attach it to the side of the enclosure box protecting the EVSE circuitry, with screws from inside. Use 3, about 3mm plastic screws, drill template for the box…
These are all currently available results.
