Counting matching models…
This is a bait station for insects, in other words, a container that houses insecticide or poison in a way that's attractive and accessible to insects, but less accessible to pets & other wildlife. I was prompted to design this station…
after my cat got into this station, I would now recommend my own from-scratch redesign, with a clip-on lid . — Strictly speaking this is of course not a trap, rather a bait station, i.e. a small container to apply poisonous bait for…
I had a lot of trouble with too much friction with the existing model, and needed to tweak it to prevent my extruder from skipping steps. While doing so, I ended up re-modeling everything from scratch with the existing model as a base.…
I created this while exploring whether I could optimize a popcorn popper's fan . If you are looking for guidance on designing an efficient and effective fan, take a look at Bleier's Fan Handbook, which has all the relevant equations in…
Printing PLA, 3 walls since this will be handled quite a bit. Split in half using dowels in your slicer, then re-combine and glue together the two pieces. I printed them face down on a smooth PEI sheet (not for PETG!) to assist with…
A carriage for an Ender 5 modified to run on a linear rail. The STL attached is for a MGN-12 rail, but the FreeCAD file has a spreadsheet and instructions on how you can make it work for any linear rail. Printing PLA is suggested for…
This holder attaches a bobbin to the corresponding thread spool so you can store them together in place. Based on the v5 from the original version. FreeCAD file included so you can adjust it, but warning, it's a laggy file.
Disclaimer This does not work well at protecting from solar radiation. The temperature on this day did not exceed 72 °F, but the sunlight hitting the wall behind it created a top temperature of 89 °F. I would only suggest using this in a…
This is designed for use with two-piece curtain rods, where one side fits into the other and has a plastic bit to prevent the parts from sliding. This is a replacement for the original version and is helpful when automating curtain…
Suitable for places with 120VAC wall power. BOM Honeywell AT150A1007 Transformer with 120V/208V/240V input Taiss Universal Changeover Switch (4-position), LW26-20-4/2 AC Power Socket. Mine reads “AC-14-F1” and fits in a hole…
The feet on my Delta Cycle Michelangelo bike rack keep sliding around on my floor. This holds them in place. BOM 2in double-sided sticky tape. I used VHB, but perhaps something thinner would work better Printing 2 feet, so print 2 copies…
Samsung makes their stove knobs out of what feels like soft PP, not something tough and durable like ABS-GF. That means that this little metal spring that holds the knobs onto the stove causes the knob stem to crack. This part rectifies…
This is a wall mount for the “P6 Automatic Soap Dispenser”. It already comes with a wall mount, but the mount is made out of some sort of extremely slick plastic that I can't get to stick to my double-sided VHB tape. This wall mount fixes…
Designed to fit a faucet with a 6.6mm hole. Parametric FreeCAD model included, so you can edit to fit your needs Can be used by cutting in half like Kitchen Faucet Index Button , which inspired this model, or with a multi-color printer.…
Makes sure the headphones are always perfectly centered on the wireless charging pad
This is a simple jig to create ultralight tent stakes based on these two Reddit posts: MYOG Carbon Tent stakes. Lightest in world version 2.0 DIY Homemade Lightest Carbon Fibre Tent Pegs Stakes BOM For each stake, 1x 3mm carbon fiber rod…
BOM: M5 nut Print in any material, press-fit a M5 nut. Either nylon locknut or regular is fine, the design has an inherent locking feature. The original nut has nothing to resist vibration, and also rotates in place which makes one-handed…
This rod goes on top of a 1L beaker and can be used to suspend an object for electroplating or vapor smoothing. It's designed with a lip so that it doesn't slip out of place, and is low-profile enough to allow for the beaker to be…
Only compatible with the Cascade Mountain Tech Trekking Poles Print in PETG. Fuzzy skin suggested.
I suggest only using these temporarily, while you are able to get a new window sash ordered. Start by measuring your original window sash against the drawing given. If it doesn't match, this won't fit. FreeCAD files are included so you…
A small cover for the hole in the wall behind the wifi router shelf. Just rests in place through gravity, perhaps a better design would have a little clip or something. Printing Print with the same material as your shelf Assembly Put it…
Also provided is the FreeCAD sources, which you can use to modify this to fit your particular situation. BOM 1x mounting plate 2x the flat-top screws that come with the mini-PC 4x #6 wood screws for mounting Printing Print in ABS or PETG,…
Fits the Wiha System 4 ESD Safe MicroBits Set, as well as an after-market micro-bit to 1/4" socket so I can use these micro bits with my other screwdrivers. You may optionally glue in a 6x3 magnet to hold the bit adapter in place.…
First off, while I've included source files (including OpenSCAD, svg, python script), I strongly recommend that you just print the .3mf file. Spitting the braile & printing it in this orientation is critical to make it readable: Another…
ESP CC Dimmer A Wi-Fi constant-current LED dimmer running ESPHome. Check https://github.com/flaviut/hardware/tree/main/esp_cc_dimmer for source code & the latest version. Intended use Designed to clamp onto wire shelving to dim a plant…
Print in PETG ideally. Then place a hose on it, and wrap it up in a sock. Use a ziptie to secure it all together. Note: the demo strainer is just a demo. There's a spreadsheet in the FreeCAD document that allows you to resize it to your…
These are all currently available results.
