Counting matching models…
Model printed entirely in PLA, given the abundant quantity of details, I recommend a print quality of 0.1 for the small parts and 0.1 or 0.15 for the remaining parts. No screws are required for assembly but only pieces of 1.5mm wire to…
My second job after fire ladder…static model caterpillar d11, for questions contact me at:[email protected]. A lot of time for drawing and printing ,but result is impressive!!!!All pieces are optimizer for print with minimum support---
The 285mm long Scania tractor model features steering and freely rotating front wheels. The model was printed entirely in PLA, with a quality of 0.10 and 0.15, depending on the size of the part. To add a touch of realism, we printed the…
Approximately 700mm long model of the MZKT launcher. The model has 8 axles of which the first two are steering and the last 3 are steering on the opposite side, on the back there is the rotation control system. The silo can be held in a…
Who doesn't like yellow forklifts? Everyone loves yellow forklifts! Simple model to print and make. Working steering and fork lifting system. To assemble it you only need a little glue and some wire for the fork system hidden in the rear…
Detailed model of the legendary English Mark V tank. Very simple assembly and parts optimized for printing with very few supports and made in dimensions suitable for the mk4 printing plate. For assembly I used simple glue and no screws.…
Approximately 600mm long model of the CAT 395 excavator. The model has working tracks, a rotating floor, and a fully movable arm and bucket. The model is printed entirely in PLA with a resolution of 0.20 for the larger parts and 0.10 for…
Model made with great attention to detail, assembly requires a good degree of manual skill. Working wheel mechanism and good level of cabin interior detail.
minifig scale samurai armor (minifig not included)
The model was printed entirely in PLA, with a quality of 0.10 and 0.20, depending on the size of the part. The two rear ramps, held in place by a tie rod, can be lowered when unlocked, allowing an equally small vehicle to ascend... You…
Easy to build model of the German WWII truck Opel Blitz. Model printed entirely in PLA, in 0.10 for the smaller parts and 0.20 for the chassis and cabin. Steering front wheels using the drive shaft as a control. Scale model with mobile…
Over a meter tall model of Nelson's flagship. Easily printable model with few organic supports with layers of 0.1 and 0.15 To make the rigging I used 1.5mm modeling rope and a thinner one for the linkage. To create the upper meshes of the…
A model of the centoporte (literally translated "hundred doors") passenger carriage, in service from the 1920s to the 1980s on the Italian state railways. Very simple level of assembly given by the joints, detailed exteriors and interiors…
Accessory pack for a swat operator consisting of: -Tactical helmet -Bulletproof shield -Door-breaking battering ram -Mp5 -M4 with scope and flashlight -Bulletproof vest with SWAT logo
Model of the German 20mm Flak 38 anti-aircraft gun. Easy to make model, printed entirely in PLA in layers of 0.10 and 0.15 The model can be displayed alone or in a version transported via a special trolley from the Opel Blitz link below…
collection of clothes and gadgets compatible with lego minifigures
Good looking but also functional, just turn the flywheel to see the movement of the pistons and, if you connect the pulleys with a rubber band, the valves will also move... Opening and closing times of the valves, based on a 4-stroke…
A nice scenic object in steampunk style but also functional, just insert your phone inside the slot (available in 3 variants: 10x76, 12x82 and 14x90mm) and just like steam, the sound will pass through the tubes and come out. Print and sound
Highly detailed, easy-to-build and assemble model of the HIGH MOBILITY MULTIPURPOSE WHEELED VEICHLE. To make the radio antennas, the steering rotation pins and the door, trunk and hood fixings you will need some pieces of 1mm iron wire.…
The sd.kfz 232, abbreviation of Sonderkraftfahrzeug 232 or special vehicle model 232, was an armored exploration car used by Germany in the 1930s and 1940s. This model is the 8 rad version or 8 wheels, and just like the original it has…
Set sail from the city of Philament for a river cruise on the "Spirit of 3D" steamboat. This model, largely inspired by the real "Spirit of Peoria," is not particularly difficult in printing ad assembly. To maintain good curvature of the…
1:10 scale model of the iconic Fiat Panda. Model approximately 35cm long. Parts printed in PLA with 0.15 and 0.20mm layers for larger pieces. To assemble the door, hood, and tailgate hinges, you'll need 1mm wire. The same material is also…
Highly detailed, easy-to-build and assemble model of the HIGH MOBILITY MULTIPURPOSE WHEELED VEICHLE. This model is the version of the M998 converted into a troop and cargo transport vehicle, with a large cargo bed and additional seats for…
Highly detailed, easy-to-build and assemble model of the HIGH MOBILITY MULTIPURPOSE WHEELED VEICHLE. This model is the version of the M998 converted into a tarpaulin humvee, with a soft covered rear section. To build this version, you…
1:10 scale model of the iconic Fiat Panda Van version in SIP livery. These vehicles were used by technicians of the Italian telecommunications company SIP to carry out maintenance and repairs on telephone systems. Model approximately 35cm…
Torso and legs protection for your little EOD officer
"Miniature" model of the Liebherr LR13000 crane. This model of the LR13000 exceeds one meter in height and is completely dynamic, replicating all the movements of the original crane. The model is designed for motorizing the lifting part…
These are all currently available results.
