Counting matching models…
Edit: I just found out that @jerrymk_985120 made the OG Clickfinity . That's where all the magic happened. Sorry I didn't acknowledge all your hard work earlier, Jerry. I couldn't have done what you did. Recently found NoWarrenty's…
The Lowe's Mini Toolbox is perfect for adding a 3x5 Gridfinity baseplate in each drawer to use x3 and x6 height bins. I've modified one of my Clickfinity baseplates to incorporate spacers on each side; none are needed for the front and…
I was getting a little lost trying to navigate around all the ever expanding number of riser models, so I thought I’d compound the problem and create one to add to the list. I was hoping to create something simple to print and assemble,…
Maybe you like the Original Clickfinity Refined but think it uses too much filament, or maybe you were just looking at different Gridfinity baseplates and found this. Either way, this might be what you are looking for. Clickfinity Refined…
3/31/25 Version 2 is out! Realizing that you might not have the exact size screw you need, I made 2 versions using a M4x12 or M4x16 screw, depending on what you have in stock. Put the screw length above the screw hole. Added slots for…
This is for those of you who want to simply add LED lighting to your print area and have been turned off by some of the complicated prints. I cut down my simple LED riser with vents to an even simpler LED only riser. This model only adds…
Replacement floor plate to enable easier seating while loading a magazine into your Canik. The extra thickness allow you to slap the mag in place without the magwell getting in the way. I've tested this one on my METE SFT with the magwell…
A remix of ZzoyozZ's Y splitter. Put it in a box, added some 10x3mm magnets, stuck a logo on it. 01/26/23 Added one modded for 8x8mm magnets.
Remixed Jarhead's excellent spool adapter for 200mm cardboard spools like Elegoo, Overture, and Polymaker (note; this SHOULD fit a Polymaker spool, but I don't have a test spool here. If someone could test it out for me that would be…
Wanted a magwell with a little lower profile than the ones I was finding for my Night Stalker with a Prodigy Magwell. Ended with with a snap-on design so I didn't have to change out the mainspring housing pin. Slide it on and snap it into…
Wanting to use Taurus TX22 full size 16 round mags in your TX22 Compact? They fit, but leave a gap between the top of the floor plate and the bottom of the magazine well. Does that bother you? Me too, so I wasted a lot of time coming up…
I modified the grip by davestation to make it a bit longer. He did all of the heavy lifting. A forward pistol grip with M-LOK attachment to hold an extra Glock mag for your pistol. You will need a mag release spring, or you can make one…
Mount to attach a Blink Mini cam to monitor your print. Attaches to the top hinge of the door. You will need 2 M3x6 screws to replace the screws on your top hinge. And a Blink Mini, of course. You can print both on the same plate. I…
NOTE: I designed these models using my MC9 with the Taylor Freelance backstrap installed; however, the TF backstrap sticks down more than the stock ones. I'm in the process of updating the models, so anything with "TF" in the name is made…
I needed a quick way to splice 4mm OD PTFE from my Bambulab AMS to my P1P, and needed it to have no resistance as it was being fed through. The center guide is slightly larger than the 2mm ID as the filament exits the AMS side, and…
I needed some bag hooks for my Ford Maverick, so with a little bit of trial and error I came up with some that fit nicely in my OEM Bed Track system (I'm assuming that the track system is the same across all Ford Trucks, but haven't…
Modified rtj's excellent splitter to a 3 way for use with my Bambu P1P.
Mirrored Plates uploaded 5/6/24. Added spacers to the original 4x3 baseplates to make them fit in the drawers. Wanted to modify my Clickfinity Refined plates to fit inside the HART Stack System Two Drawer Tool Box from Walmart, but found…
Tearing the sides off of Overture carboard spools works pretty well, but there's the problem of the spool spinning while trying to retract when it gets low. This insert solves the problem by sliding in-between the core of the carboard…
MiniCleats , because we need even more mounting systems. While installing a French cleat system in my shop, I had a thought; what about adapting this into (yet another) 3D organization system? I’ve been using the Honeycomb Wall concept,…
2/28/24 v2 released! Got rid of the hook because it was basically worthless; was too low to hang a grocery bag on it. Adjusted model to allow for most common brands of eyebolts Added locking nubs to keep tie down from vibrating loose.…
I needed to feed my AMS units into my P1P from the left side and wanted to avoid a large 180 degree loop that could put more drag on my filament, so I made a bracket to mount the buffer vertically on the side. I added a feed guide to keep…
The Holosun 407K is a direct mount on my Tisas Nightstalker Double Stack, but I found that even with the elevation adjustment to the limit it was still shooting too low. After getting a shim off of Amazon only to find it wouldn't fit on…
The gap between the Wasatch Arms compensator and the front of my trigger guard was bugging me, so I created a snap-on insert to fill the gap. I made it out of ABS; you can use PETG or even PLA, though PLA will sometimes break while trying…
These are all currently available results.
