Counting matching models…
Update: I've added a new model for printing which fixes the wrong counterbore holes (recommended by MG-Grafik-Design - many thanks!) This new model is not tested on a real Zwift Ride (since I don't have one atm)! But I assume it will fit…
I'm running out of such parts all the time and so I've created it by myself and printed it with various left-over materials. Works best with some softer and not so brittle materials, for really strong mounts I recommend Nylon or other…
This is a remix of https://www.prusaprinters.org/prints/26045 I have increased the bottom bracket to fit the thicker laptop and decreased the width of the stands since I have added a middle bar to keep the raisers in place when I take…
A case for the Sidekick64 cartridge based on a Raspberry 3A+ This case is based on the original 3d design which is available at the Github page of this project but was built for the larger version of the Raspberry 3 I'm still working on…
Althou pretty satisfied with the 3d-printed stand from the original I went for an even steeper version to reduce glare on the display and to make it a bit more comfortable to use as a general shortcut device for other applications. I have…
A rather flat food dish for dog or cat food. I've created this for our dog, she's very sensitive to noise and dislikes common food bowls since they produce some rattling noise on hard surfaces. These dishes are soft (TPU90A), easy to…
I wanted to have a multicolor print so I did this little tag in two versions, one with keyring and one with holes for magnets. So now it is easy to carry the address with you all the time :) Printed with 0.4 mm nozzle and Prusa PETG.
I was looking for a way to stack 2 C64s without building a rack or so. I came up with this, eventually. The lower C64 can be moved forth and back a bit to adjust the position to personal needs. I may create another version that can be…
This is a side plate for the breadbin case C64 for installation of an internal SD2IEC device. The main purpose was to install additional buttons for disc image change and an on/off switch. The used switches can be clicked into the side…
I've made these parts to optimize the controller handling for especially games like Tetris or Doctor Mario. You can either print the whole 4-way button or use the shims to tune your controller as you like. Recommendation for the 4-qay…
There are two versions, one version is for printing the black applications by changing the filament at a certain layer height, the other version is for printing it as one piece using in layer filament change (like with a MMU) You can…
Printed it using PETG but should work fine with PLA too. 0,4 mm nozzle at 0.15 mm layer height, 0.2 mm layer thickness will work fine too. The letters are just one layer thick, if you get troubles sticking them to the bed then try to…
Very easy to print, expandable board stand for boards for the C64, VC20 or similar shaped PCBs. Boards are angled at 64° ;) Good for organizing boards for repairs or testing.
Two versions of stands for the Analogue Pocket. They can be used just to hold the device, to charge it or to charge it and have an audio connection. No HDMI like the original! The charge/audio version (Stand 2) is highly experimental! The…
A simple and easy to print laptop stand for the Lenovo ThinkPad L13 Might work for other laptop models as well prints well with 0,4 mm to 0,8 mm nozzle with about every material (maybe not TPU :) ) I've used Tree Support for the little…
Replacement for main door sealing. I've couldn't find the correct type for my door since all of the common sealing are too small so I decided to print them myself. I've used TPU90A which is perhaps a bit too stiff, a softer material would…
A case for the Pinecil soldering iron with space for 5 extra tips, the mini stand and for the press in adapters for inserts to have all in one place. 2 versions of the lid, one for the additional cable buddy and one that fits normally.…
some bottom saver / protection stands for metal bottles like Klean Kantine and similar. Protects the bottom of the bottles when dropped or even helps for bottles that are already dented at the bottom. I've created different versions since…
A sturdy stand with space to store additional soldering utilities for the Pinecil soldering pen. All parts are aligned as they need to be printed. The small holder may require some support. Depending on the printer settings and precision…
This case is made to store the Chip Tester Pro V2 by Backbit. The idea is to have a rigid case (PETG as shown in the picture) with a softer inlay (TPU90) and a lit that stays in place by the help of magnets (8x3mm) The 3mf contains all…
These are all currently available results.
