P
PrintablesBas
Remix of ikea-lack-table-stack-coupler-model_files
Remix of ikea-lack-table-stack-coupler-model_files Holes and corner fittings added
- Downloads
- 359
- Likes
- 46
- Rating
- 4.67
All models
Counting matching models…
P
PrintablesBas
MMU2 filament buffer and spool within an Ikea drybox 365+ 10.6liter, Version 4
This is a filament buffer and spool within an 'Ikea drybox 365+ 10.6 liter' for the MMU2s. I wanted my filament-spool, but also the whole route to my MMU2, in a dry and protected environment. So I designed a buffer within the largest…
- Downloads
- 268
- Likes
- 80
- Rating
- 5
P
PrintablesBas
Stackable Faceshield-band with integrated cap.
Stackable Faceshield with integrated cap . Print instructions This is a stack-able design of the EU face shield with an integrated cap. A test with a print of two stacks of 4 pieces with a layer height of 0.3 mm and a speed setting of…
- Downloads
- 117
- Likes
- 0
- Rating
- 0
P
PrintablesBas
Remix of the MMU2(s) Filament Buffer (standing or hanging)
This is a remix of Mordiev's great work out of a hanging mount for the original MMU2(s) Filament Buffer . https://www.prusaprinters.org/prints/30809-hanging-buffer-mount The difference is that the clip is separate printable from the body.…
- Downloads
- 101
- Likes
- 8
- Rating
- 5
P
PrintablesBas
A (remix of) a gripper based on the fin ray of a fish tail
This is a gripper that bend around the stuff you pick up. It is based on the principal of the fin ray of a fish tail. See also this video of a (bit too old and dry) fin ray of a tilapia fish: https://vimeo.com/22739805 This gripper can be…
- Downloads
- 77
- Likes
- 11
- Rating
- 4
P
PrintablesBas
Test with preprinted support for PETG models with overhang
I needed to print mechanical parts of PETG with an overhang. I was not satisfied about the standard support option. The printed support of PETG is difficult to remove and resulted in a sagged 'roof' and surfaces that needed too much…
- Downloads
- 46
- Likes
- 6
- Rating
- 0
P
PrintablesBas
Test 7 with Iglidur i150-PF filament
This is the 7th test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I tested the first layer as a follow up from test 6. This time I used the smooth steel sheet with PEI coating, without glue…
- Downloads
- 45
- Likes
- 3
- Rating
- 0
P
PrintablesBas
Test 4 with Iglidur i150-PF filament
This is the fourth test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I used the following hardware: -steel sheet (a steel sheet without coating). -enclosed printer with ventilation control…
- Downloads
- 41
- Likes
- 0
- Rating
- 0
P
PrintablesBas
Test 1 with Iglidur i150-PF filament
This is my first test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I used the following hardware: steel sheet with one layer of glue. (a steel sheet without coating) enclosed printer with…
- Downloads
- 29
- Likes
- 2
- Rating
- 0
P
PrintablesBas
Sun-visor for the ABUS bicycle helmet Urban-I 3.0
Sun-visor for the ABUS cycle helmet Urban-1 .0 3.0 Made for size 51-55 cm, I have no idea if it fits other sizes. So I made a test print to test this. Print upside up. Use supports from the print bed. The support is a bit difficult to…
- Downloads
- 28
- Likes
- 5
- Rating
- 0
P
PrintablesBas
Test 3 with Iglidur i150-PF filament
This is the third test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I used the following hardware: steel sheet (a steel sheet without coating). enclosed printer with ventilation control with…
- Downloads
- 27
- Likes
- 1
- Rating
- 0
P
PrintablesBas
Sun-visor for the ABUS bicycle helmet Urban-I 4.0
10 june 2026: revision 3 with a better fit. Sun-visor for the ABUS cycle helmet Urban-1 4.0 Made for size 57-61 cm, I have no idea if it fits other sizes. So I made a test print to test this as shown in the last 4 pictures. Print upside…
- Downloads
- 21
- Likes
- 2
- Rating
- 0
P
PrintablesBas
Test 2 with Iglidur i150-PF filament
This is test 2 and a follow up from: https://www.prusaprinters.org/prints/48764-test-1with-iglidur-i150-pf-filament Changes made to test 1 are: I did a cold pull with PLA to clean the nozzle (was clean) 3 layers of glue with drying in…
- Downloads
- 20
- Likes
- 1
- Rating
- 0
P
PrintablesBas
Test 6 with Iglidur i150-PF filament
This is the 6th test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I tested the first layer as a follow up from test 5. This time I used 3DLAC on my steel sheet. I changed the 'minimum travel…
- Downloads
- 20
- Likes
- 0
- Rating
- 0
P
PrintablesBas
Wall holder for the Soehnle Style Sense Compact 100
This is the wall mounted holder for the scale ' Soehnle Style Sense Compact 100'
- Downloads
- 19
- Likes
- 1
- Rating
- 0
P
PrintablesBas
Test 5 with Iglidur i150-PF filament
This is the 5th test of a series with the filament of Igus: Iglidur i150-PF. https://www.igus.eu/product/12404 . I used the following hardware: -steel sheet (a steel sheet without coating). -enclosed printer with ventilation control with…
- Downloads
- 18
- Likes
- 1
- Rating
- 0
P
PrintablesBas
Water bottle mount for HP Velotechnik bikes
Fits on mesh seats on HP Velotechnik bikes Extra needed are two standard bike waterbottle holders, nuts and bolds.
- Downloads
- 8
- Likes
- 1
- Rating
- 0
These are all currently available results.