Counting matching models…
Hydra Compatible 4.1 Model updated for Errors in model that someone reported bambulab 2 row desiccant holders, this works with a hydrometer and sits behind it as well in total you can fit 5 inside, 6 without the hydrometer and you do not…
This is a remake of https://www.printables.com/model/272302-bambu-lab-ams-hub-ptfe-button, the difference is that its been shrunk with the bowden tube inside, so it fits on the AMS Hub PTFE Tubes which makes it backwards compatible with…
NOTE 3MF is Required in this model as negative parts are used Pla or ASA or ABS, it is a little flimsy as PLA but it does work, one in photos is in pla This will work on EITHER the left panel screws or the rear panel Screws 2 M3 Nuts need…
Bambu X1 AMS Hub Exhaust Muffler / Fan Silencer, printed mine at 50% infill PLA, screws are M2.5x10mm and M3.0x12mm Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
This Gcode is the original G Code but in this one it scans for the bed QR Code Then it does a Home Check so that if it doesn't see the QR Code it PAUSES asking for BED or Continue, IF you add the plate IT NOW SCANS that Plate and then…
Tested in PLA and PETG at 100% infill Note this only works on the Tag Side of the Spool Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
Bambu Sticker Set Handle and Base Less time to print, infil I did was 20% but it might be good at 10, this was created because its less time to print then Bambu mod and it has a base that slides on for better laying the sticker so you can…
This is to bring up the AMS Hub higher into the air for easier access You will need: Tilted_Lower : 2 M3 Screws size M3-12 and 2 M3 Nuts Tilted_Top Final : 1 M3 Screws size M3-12 and 2 M3 Nuts Note if your having feeding issues its…
This attachment fixes the failed to pull filament messages, put the higher tab at the rear so that it cant break off when moving to the front rail to do a Filament Cut Printed in PETG for some flex but at 99% infill Want to buy me a Slice…
Make sure you use correct print orientation with the charge port cut out facing the print bed I printed this in PLA at 100% infill for strength over time from drops Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
FOR Non AMS Users Upload to SD Card to always have the Filament Buttons of your Choice SAVE NOZZLE gcode keeps the nozzle in place and takes it to 290 for a bit to get the gunk out but has no retract in the code or extrude These Buttons…
Bambu Lab Turn on the Logo X1 Button, change file extension to .gcode Printables doesn't like the on gcode, scroll down to other Files Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
Recommend ASA or ABS or PETG Print as its outside in my case Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
Recommend ASA or ABS or PETG Print as its outside in my case Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
Make your Yeti sit Flat again and not clang when you set it down NOTE over time water can sit in this and cause the cup to rust, clean now and then and dry with a paper towel PETG 25% infil no support needed Note the 3MF file offers a…
V9 Entrance is now easier to push in __________________________________________________________________________ Now with Directional Arrow This Model is curved all the way around allowing for easier compression into the spool Step 1 Rip…
Fan Cover to cool SSD and Ram for: Mini Gaming PC AMD Ryzen 9 7940HS 2TB PCIe4.0 SSD 32GB DDR5 5600 MHz RAM, Desktop Mini Computers Windows 11 pro, Radeon 780M Graphics, 2.5Gbps LAN, HDMI 2.1, 8K USB 4.0…
https://dutchdevelop.com/bl-led-controller Final V2 Has USB Cutout for firmware and Pins Named correctly to WW and W --Note Check the Wiring on the cable, next to the LEDS it says the letters, for me Green and Blue were opposite from the…
Added a Button Press to turn the Device On If you want it in two colors do a layer change at layer 8 ASA recommended BOM: Button https://www.amazon.com/dp/B01J0PFX3Y Wire Connectors for making it Clean https://www.amazon.com/dp/B07C7VSRBG…
PLA Printed Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
Recommend ASA or ABS or PETG Print as its outside in my case Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
PLA Printed without supports Want to buy me a Slice of Pizza? http://buymeacoffee.com/TheTexMech
These are all currently available results.
