Counting matching models…
Needed something to hold two power supplies so used the one closest to the dimensions I needed. I moved the screw tap to be centered, removed one of the multiconnect slots and lowered from 100 mm to 55 mm. I had a comment that the screw…
Print approx. €1.54–€1.89 excl. taxPreliminary estimate for PETGSource material: PET
I have been working to create a command strip mount for the OpenGrid lite. Used this model and one of the directional lite with some spacers. This allows you to connect this to the command strip, with a spin in holder to add parts of the…
Print approx. €0.30–€0.37 excl. taxPreliminary estimate for PETGSource material: PET
I used the original and build a PLA sliced version and saved the modification from the “Cat Face Bookmark.STL”. I reduced it to us in a paperback book. Have lots of family members that love cats. Hope it helps others save a little bit of…
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for one variant
I took the based I created for my Lite version and pulled the OpenGrid SNAP. To build this one for the full OpenGrid version. I got a couple of comments that I missed from my other version (Lite version):…
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for PETGSource material: PET
Needed a few accessories for the OpenGrid that is not part of the OpenGrid Underware set. Used the ones from UnderWare to start the base model and split and put back into a single printable model. Please let me know how it works for you.…
Print approx. €0.95–€1.16 excl. taxPreliminary estimate for PETGSource material: PET
I had a bit of issue printing from the object after looking at the timeslice. The top of the lid does a bit more movement than just using the limited contact with the bed. I resliced adding a 2mm brim and the printer had no issues…
Print approx. €0.55–€0.67 excl. taxPreliminary estimate for one variant
Make sure you push in the two triangles close to the short end of the command strip first and tilt down towards the long end to snap into place. Compatable with all the channel models that David D has created. If you have any issues…
Print approx. €0.30–€0.36 excl. taxPreliminary estimate for PETGSource material: PET
I have two of the below 1U rack mounts. I found that as most of what I build I had a part that I could not use due to the way I ran electrical wires. Of the 5 PI mounts with SSDs I put it on the bottom shelf of the Lack Enclosure I built…
Print approx. €14.04–€17.16 excl. taxPreliminary estimate for PETGSource material: PET
I kept looking at my kitchen sponages either in a pan with soapy water or in a place I could not find. This allows for two sponages and a place for the scraper. It allows to drain the water back into the sink. Please let me know how it…
Print approx. €1.41–€1.72 excl. taxPreliminary estimate for PETGSource material: PET
I needed a stand with extra wire storage, could not find one. Had an idea and the first couple did not work or work well, but did not need to be in parts. So we ended this one on version 5. If you hold the HomePod upside down. You can…
Print approx. €1.01–€1.24 excl. taxPreliminary estimate for PETGSource material: PET
I have a friend that has a round glass patio table that lost one of the table top supports. The support is 40x45 mm that locks into the rim and supports the glass table top. I have a picture of the original as well as the one I made from…
Print approx. €0.43–€0.53 excl. taxPreliminary estimate for PETGSource material: PET
I did not see a sliced version. Built one to make it easier for me to print a couple. Had the file and uploading here to help save a bit of work for the next person.
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
I needed a single set of squares and downloaded the step file, went to fusion. Was only able to get some of the faces removed. Took the remaining parts and cut them off the top and saved the above prusa slice version I've uploaded. Please…
I needed a second set of three parts. I have built the holster wall dock plate included here. I will be working on the other two parts and will update this or build new based on what works best. I chatted with the vendor, but they do not…
These are all currently available results.
