Counting matching models…
Tactical reload paper towel holder for IKEA Skadis peg board. Houses rolls up to 24 cm in length and 16 cm in diameter. I remodelled the original lever and added a curve to the roll contact face. Still fully interchangeable with the…
1/18 scale version of the original 1/10 by MrStolarsky. Pins were re-aligned and the whole board was made stackable. I test printed mine in resin and they came out awesome. I designed hangers for the Traxxas TRX-4M Defender, to hang a…
Battery holders/dispensers for IKEA Skadis peg board. 18650 Holds up to 9 batteries, works with protected cells as well. Both sides need to be printed. Pegs in the holder are ofset by 20mm to mount properly and not take up too many peg…
AA battery dispenser for IKEA Skadis peg boards. Has an open top to load the batteries in. Locking pegs' position has been adjusted to align the dispenser with my other dispensers. Houses 11 AA batteries. AAA battery dispenser for IKEA…
A simple shackle for my Traxxas TRX-4M Defender bumpers. Printed in resin and painted. Paper clip can be used to be pressed in to fasten it to the bumpers. Drop of glue might be needed at the ends to secure the paper clip in (I did not…
Wheels for the Traxxass TRX-4M Defender. All fit the original rubber and have the same offset as stock by default. Alternate versions with +X push the wheel out by Xmm, the wheel sits further out. -X brings the wheel closer to the body by…
Front light guard for my Traxxas TRX-4M Defender. I printed mine in resin and glued them on. Print some spares as the thin tubes might get broken in print (0.5mm in diameter). I printed 4 at a time and one guard had one bar broken.…
7mm long drive hex for the Traxxas TRX-4M Defender. I did not like how the axle thread is vissible with the stock hex drives (just asking to be damaged). This one is just long enough to have the nut flush with the end of the thread while…
Over-beefy hangers for my Traxxas TRX-4M Defender. Might work for other crawlers/rc cars. Designed for a 56mm tall tyre. Distance between inner tyre walls to be 75mm (or 75 ±40, peg holes are 40mm apart). Right wheel hanger (uploaded)…
Tray inserts for a LiFePo4 battery pack for UPS 12V7A battery case. I am using a 30A BMS to go with the battery pack made out of Liitokala 32700 LiFePo4 cells. Mine measured at around 6300mAh when discharged from full to 2.7V (per cell).…
After fooling around with 5" and a whoop, I decided to build a 3". But what fun would it be to design my own frame? Well, it worked out awesome. The frame is a TrueX, 130mm motor to motor. Overall weight (including props, battery strap,…
These are the inside pins that slide into the plastic inserts to lock them in place. Originally created the models as a request. Two lengths of pins. The shorter one is for the side/middle mounting short pins and the long one for the…
Selection of light diffusers for my Lumintop flashlights. I used Smartfil Green Glow Flex 93A, 0.08mm layer height (you cannot see the layers at all), 100% infill. Diffusers for: Lumintop GT Nano/GT Nano Pro Lumintop EDC Pico/EDC Pimi
18650 battery holder I am using a DYI 18650 (LG HG2) with spot welded nickel strips and soldered XT30 lead. The battery strap is an iFlight 10mm strap shortened by about 10mm. Supports are required if printing in default orientation.…
The original broke on me so I created this replacement part. I printed it with a 100% infill, black PLA for testing and it stayed on.
Simple lightweight clip to mount the Eachine EV100 Micro AV Recorder to a 19mm strap of the Eachine EV100 FPV goggles. Print Settings Printer: PrintBucket 500 Rafts: No Supports: No Resolution: 0,2 mm Infill: 100 % Notes: Printed with…
The fans on my MSI GTX1050Ti LP were noisy even at low rpm. So I swapped them out for some Silentium 50mm fans. Now the GPU is really quiet. This GPU does not allow for fans to be off, 40% is minimum. The 3x50mm Silentium fans setup is…
Glow in the dark insert for a Lumintop FW4X flashlight. Unscrew the front lens cap and place it on the lens (between the lens and the LEDs) to install. Watch out for the T notch orientation modeled to fit the LED power wires (T notch…
Second iteration of my Emax Hawk 5 Lowering kit. Makes the body lower using only 13mm stand offs. New camera mount, shorter stand-offs (13mm), sanded base plate to acomodate the new camera position. Using a custom cut carbon fiber camera…
Top plate mount for GoPro Session 4/5 cage with back mounting. 4 versions: a - first version, directly replacing two top side plates (not recommended) b - second iteration of the a version (also not recommended) c - third version intended…
I have made a v2 since and have been flying that. EMAX Hawk 5 lowering kit v2 --- Lowering kit for Emax Hawk 5. Makes the body lower by 5mm. New camera mount, shorter stand-offs (20mm). The camera mount is meant to be made from carbon…
Simple holder for Realacc pagoda antenna. Mounted using two zip ties. The antenna fits snuggly with the silicon boot.
These are all currently available results.
