Counting matching models…
This is a two-part housing for a cheap 64x32 LED matrix, including mounting for a Raspberry Pi 3A+ BOM 1x 192x96mm LED panel like this one . Unfortunately, this listing makes no guarantee of screw hole locations, however I've ordered…
Fits ideally over beds with a 22mm edge.
Run this through the loom and pull your wires along behind it. Not amazing but much easier to print than some others and does the job.
The clippy buckle thing on my NewBeeDrone lanyard was too big, so I removed it entirely and made this so I could use it. Integrates the lanyard more directly into the radio, in my mind. Probably works best with lanyards with quick-release…
5cm tool for picking, poking and packing. Category: Hand Tools
I bought an Android headunit from Aliexpress and it came with USB sockets on a pigtail with no way of mounting them, basically. These prints let you clamp that socket in place of the OEM headunit's USB socket, which uses it's own…
This is a bit of a re-imagining of https://www.thingiverse.com/thing:1610834 --- thanks for the inspiration! My main need was for M2 holes instead of M3, and I also wanted to offset the M2 portion so I could bolt it together properly.…
Split the exposure area when using the double-exposure mode for some fun effects. Clips firmly onto the front lens extension and spins freely when needed. Designed for the Instax SQ6 but I reckon it may fit the others as the mechanism…
A little adapter to attach those little phone fisheye, macro, etc. lenses. They use an M17x1 thread. Clips firmly onto the front lens extension. Designed for the Instax SQ6 but I reckon it may fit the others as the mechanism looks…
Stock lids were very loose. Print with PETG or another rigid filament. Pops in easily, pops out with two thumbs on either side.
This is a little case for the Sweep 2.x by @davidphilipbarr , intended to be printed in a soft TPU. It includes cut outs for the solder joints so the board can sit completely flush. This was built around the Sweep 2.1 specifically, but I…
Hang a bag on a table, or flip it to hang it over a door.
Replacement Sides for the Synthstorm Deluge. ... or cheeks, as some people say? Print either as a single piece or print split and glue them together. Print flat. No supports needed. I split them because I wanted to use wood PLA for the…
A compact parking stand for the Ninebot One A/S series. Print stand in a strong rigid material like PETG or ABS. Print 2x feet in a flexible material like TPU. Press fit feet onto the sides of the stand. The feet are slightly undersized…
UPDATE: Happy to pop the lenses out of the assembly? You might prefer this print instead . This print lets you fit FatShark-style diopter lenses onto your HDZero goggles with the regular faceplate . No need to print a whole custom plate…
Made for the Synthstrom one but these switches seem to be common! Hurts to use without shoes on otherwise. The .STEP is multi-body if you want to add some colour!
This is a replacement battery cover doodad for the Ninebot One A1/S1/S2. Mine fell off and vanished while riding so I made a copy using the one left over. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No…
The frame is sharp AF. Don't accidentally cut into your leads like I did! Print in TPU with supports. Might need to scale to get it to fit well --- it's not perfect but close enough for me. Print Settings Printer Brand: Creality Printer:…
These inserts let you fit the FatShark-sized/DIY prescription lenses onto the stock HDZero faceplate! Specifically, it takes the actual lens part of e.g. FatShark lenses. If you previously used this print of mine that takes the complete…
Some little feet and a LED strip mount for the Babyhawk. Print in TPU with supports, and then super-glue them on. I ran the wiring for the strip down the arm with back right motor since it's closest to the LED pads. EMAX messed up the…
Mine was vibrating a lot through the floor. Print in a soft and flexible filament --- I used 85A TPU. You will need to mirror one across the X-axis when printing for both sides! I ended up flipping it upside down also (i.e., print with…
These inserts let you fit the FatShark-sized/DIY prescription lenses onto the goggles! Lenses should be sized or cut to 24.5 × 17.7 mm. Print with the clips facing up, with support for the lens insert area. Pop the frame over the display.…
These are all currently available results.
