18 models
There are so many designs out there for mounting and hanging PMags, but nothing really good for USGI magazines. This mount was designed around OKAY Surefeed 30 round magazines, but should work around most USGI aluminum and steel mags, as…
This is for the first version of the T114, the one with problems. I haven't received my v2 yet to see how they compare physically. ------------------------- This is a pretty accurate version of the Heltec T114 plus screen. One side of the…
Designed for a 2025 Kia Carnival, but would probably work on other years as well, as I think they're all the same generation up to this point. The Kia Carnival has sliding seats with tracks built into the floor. These tracks are dirt and…
Here is a case for a RAK 19007 Meshtastic device. Includes solar charging, a GPS set to an ideal angle, 18650 holder, dot matrix for node ID, rails and holes for modular mounting options, and a side-located antenna to protect it and keep…
6/18/2026 Looks like there may be some size differences in mounts. I added a zip of alternatively-sized mounts, incrementally smaller. These are NOT TESTED because they don't fit my mount. Please let me know your successes or failures…
Hummer H3, 2004-2012 GMC Canyon/Chevy Colorado trucks do not have paper/fiber cabin air filters - just a mesh wire to keep large debris from entering the cabin air intake. This adapter allows you to add and quickswap a cabin air filter.…
3/23/2026 Added an interior top mounted latch for some drawers where the side mount wouldn't work. ______________________________________________________________________ I've always hated exterior-mounted and interior top-mounted latches…
It's impossible to find new bushings for Texan loaders, and stupidly expensive for used ones. People were selling 3d printed ones at ripoff prices so I figured I'd throw my own up. These cost about 15 cents and 20 minutes each to print.…
It's impossible to find new bushings for Texan loaders, and stupidly expensive for used ones. People were selling 3d printed ones at ripoff prices so I figured I'd throw my own up. These cost about 15 cents and 20 minutes each to print.…
This strainer cap allows you to pour water in one side (using the stock large-gap strainer cap) and wash out all the filth, water, and bubbles through the other side into a sink or similar without losing your stainless steel pins.
After a crash with my AtomRC Seal, the latch that secures the hatch was nowhere to be found, so I modeled up this little replacement. you need: M3 threaded rod cut around 35mm. I cut down an M3 bolt I had 1x M3 nut 1x 7/32"x11/16"…
Adding the front suspension kit from Coleman to a CT200U removes the place to mount your front rack. These arms give tha
As far as I can tell, there aren't any spent primer catchers for the Texan Loader presses. This one slips under the spent primer hole for conveniently catching primers instead of letting them roll everywhere. Print with supports…
Scan of my DNT Hydra HS635. Please feel free to use it. My only (unenforceable) ask is that, for any models that you make, you make the files public for others to print. I also included a small model of the mounting interface, including…
Replace your air intake cover with your own printed model, adding color or intake options as you please! This fits the Predator 224 non-hemi. I don't know if this fits the 212 or other 224 hemi versions, but if you have one or know,…
The stock Lee seating die deforms Hornady's FTX 357 bullets, as they have a softer nose. This die forms around that nose and reduces the deformation. It's been a while since I used this, but, if I remember right, I disassembled the die…
While replacing the bearings in my front tire of my Coleman CT200U, I damaged the bushings that hold the axle housing centered. 3D printed these in TPU and they do a decent job. They're tight around the bushing but have some play around…
I was changing the CV axle seals on my 2010 Chevy Colorado/GMC Canyon and was having a hard time driving the new ones in evenly without damaging them. This fit the profile of them pretty well (got TRQ ones, but I imagine they'd work for…
These are all currently available results.
