Counting matching models…
I was using JamKo76's Polymaker rings, but the nub/tab was always hard to push in, and the rings were a little too thick to roll smoothly in my AMS. So I trimmed 0.4mm from the base of the ring to make it fit better without affecting the…
Uses 6mm diameter by 2.7mm tall magnets. The fit of the magnets is tight, but put a tiny bit of super glue in there to make sure they don't come out. It is important to orient the magnets correctly when inserting them. I put all the…
The remix from Thejrial slices with some small holes for me in PrusaSlicer 2.2.0. I just slightly added some thickness in the area that had the hole, and the hole is now fixed.
Are you tired of always needing a flat head to adjust your 3296 trimpots? You know, the little tiny ones that come on boost and buck converters? Well, fret no more, print this little knob and you will be enjoying the good life of flat…
Eryone started using cardboard spools. This is a fast print, if you use these settings, it is about 12 minutes on the X1C. The little lip hold the spool, and the single tab keep the ring on the spool while keeping as many holes open as…
The roof has a slight indent to make alignment when gluing the house easier. To print this to multiple colours, slice the house and track, add a pause at 12.40mm (assuming 0.2mm layer heights), change filament for the one you want to use…
For a toy crane I made a better base for ( https://www.printables.com/model/349241-toy-crane-stable-base ), it was just begging for a load carrier so you can haul things to new heights with it. Use a M3 x 20 hex head bolt as the connector…
The original knob was too big for my speaker. The volume knob stub on my speaker is 6mm diameter, so I took the original design from DivePADI and shrunk it a bit in order to retain the original geometry (which is very nice, thank you).…
@MediaMan3D's original back lifter didn't fit my X1. I've just used his model and trimmed the insert slots so they fit! I also removed the curved finger grooves as those supports didn't come of very smoothly when sliced with BambuSlicer.…
If you have a Zerowater dispenser system, then you know this button for the tap. It's fine if you just want a small cup of water, but if you say, need to fill a 4L jug, your thumb is going to be numb by the end. This is where my Zerowater…
This is an remix to the single switch key hanger. I did make the vertical hanging shafts slightly thinner (they were 2mm, now they are 1.5mm) Should help the switch plate sit less awkwardly. This hanger will fit if the two bottom screws…
Thanks to Fantastic Plastic Person's bridge with tunnel. This just widens the tunnel a bit along the bottom to make it easier to fit some 3rd party tracks (maybe even some gentle curves).
A popular toy construction set ( https://www.amazon.ca/Construction-Vehicles-Engineering-Excavator-Interchangeable/dp/B08DCMYFHW/ ) came with a terrible base. It was far too light, and the only thing holding it was suppose to be a suction…
My glasses came with these magnetic clip on sun glasses, they are great, except they are quite fragile and I've had a number of these break over the years. They are quite expensive to replace by themselves (I guess they want you to just…
Did your On Stage MS7700B Tripod Microphone Stand tensioning ring shatter into a thousand pieces? Fret no more, print this piece in TPU, and you will have a piece that will allow you to adjust the height of your mic stand and also last…
Did you get an Ikea chocolate bunny (VÅRKÄNSLA) and strangely, it disappeared magically, leaving you sad, and lonely? Well, have no fear, as long as you have some brown (or wood) filament, you can recreate this chocolate bunny. And this…
These are all currently available results.
