Counting matching models…
Now that hunting season is once again upon us I wanted to make a basic shotgun holder that I can use while sitting in a blind. This basic gun mount can be used on Atv racks or heavy duty folding chairs with a tube diameter of 7/8". This…
A Simple remix to hold 2 pairs of scissors or pliers to your Skadis wall system. This holder works well for pliers with dipped handles. Some moulded handles may not fit as they tend to be wider. For Best results print with the flat part…
A simple remix of Mistertech's wasp traps. I added some gussets near the entrance holes to make the print a little stronger since it broke the first time it was knocked over.. I also added a 3mm hole with some support so you can thread a…
A modified of the Clip Stick to accept basic painters poles or even broom handles. The threaded portion is a little thicker than it needs to be but it helps when wearing gloves. Supports - Yes Print with the threaded part flat for minimal…
A quick remix of Printit Tom's Riptide Mainsail Glock Holster to include a belt loop for 1.5" belts. The added thickness also adds a thumb rail for easier removal of the pistol. I primarily intended to use this as a costume accessory to…
A 4 piece expansion pack for the hexagonal animal tiles by Jura Švébiš. I liked his design so I decided to add some new animals to the collection. There is now a moose, bighorn sheep, a mallard duck and a bison. I may add more animals if…
A simple remix to hold a large glue stick of 30mm diameter to your honeycomb wall. I added a locking push in tab for the honeycomb walls for a secure fit. Printed in PETG
A slightly wider holder to fit the comfort grip pliers like Craftsman, Mastercraft of Kobalt. The original file printed with a slot width of 14.3mm and unfortunately was a very tight fit for my pliers and you could see the bulging on the…
The sarcophagus from The Fifth Element movie.
An upgraded go-pro compatible holder for the UV5R radios. There is an added slot for better belt clip retention to help prevent movement under off-roading conditions. It also significantly helps reduce noise from the radio rattling around…
A simple remix to hang the honeycomb scrapers on a Skadis wall. The original scraper can be found here. https://www.printables.com/model/122894-hexscraper-printbed-scraper
A remix of the SKADIS - Ratchet holder by Kenneth Giese Hejnfelt but for larger sized ratchets with a stronger hook. Many of the 3/8" sized ratchets would barely fit and there was no hope of getting a ½" drive to fit. By simply up sizing…
Im sure this is a remix of a similar design but with a thicker base to accommodate the use of double sided tape. I have downloaded other plates similar but the backing plate was too thin to accommodate the use of double sided tape. The…
A stand to hold rolls of craft paper or butcher paper. This model will require some additional items you can purchase at your local hardware store. There is also some basic math skills required to ensure you purchase the correct lengths.…
A multi functional doorstop that can be used in a variety of ways. Besides being used like a traditional wedge style doorstop, it can also be used over the hinges to hold the door open without actually entering the room. All you have to…
I was very surprised to see no one has yet designed a holder for these tube cutters to use on the Honeycomb Storage Wall so here it is. Print as you need it but it is recommended to use 5 wall thicknesses or more for maximum strength.
I couldn't find a holder specifically designed for the Gearwrench brand of T handled Torx wrenches so I modified Ryra's version to better suit my needs. This holder will fit the GEARWRENCH 7 Piece Torx Key T-Handle Set Part number 83517.…
Made specifically to fit 3/8" throw bags, this float allows you to attach a carabiner to your line without it immediately sinking into the water. Could also be used as heavy duty rope float for marking out pool lanes or what ever else you…
Inspired by Ozark Laser Engraving's original design, this simple remix is designed to hold the 10 pack of Richard's Paint Pyramids that are available at most hardware stores. If you have already purchased those painters pyramids from your…
Victorinox/Swiss Army Knife Holder to hold 3 or 5 knives. I expanded on MFM15's design to allow each holder to hold 3 or 5 91mm swiss army knives depending on your preference. It also works with Alox scaled knives but is a bit loose at…
How many times have you pulled up to a drive through only to find your window was frozen shut? In the past there was only two ways to deal with the situation. One was to park somewhere warm until the window warmed up enough to open. The…
A version of the 91mm Plus scales for those that remove the corkscrew or phillips driver from their Swiss Army knife. This scale allows customs modifications to your knife while still maintaining its cosmetic looks. Unfortunately you will…
Simple Honeycomb Wall clamp to hold AA or Cr123 cell flashlights. Also works well for other round items like broom handles. Print in PETG or ABS with the recommended settings for your filament. PLA is NOT recommended as it will deform…
A simple yet effective holder for your Thwack Hammer. Comes in screw on and Honeycomb Wall patterns. Skadis wall to be added later. This robust and tighter fitting design means your hammer wont fall off the wall (unlike other patterns on…
A remix of LooseLunch's Williams Screwdriver Wall Mount so it is now compatible with the Honeycomb Storage Wall system. Print with at least 5 outer walls and supports for maximum strength. If you like this remix please like and post a…
A quick slip mounted fishing rod holder for flat surfaces. The base mounts to any flat surface like a truck canopy, the side of ice shack or even your boat. The rod holder portion simply drops into the base for easy installation and…
Createx 4oz or (43mm diameter) bottle holders for the Honeycomb Wall System. Each rack will hold 4 bottles. and has 3 wall attachments to prevent sagging if loaded with heavy paints. Print in the orientation provided with at least 4…
Anyone that uses these restraints knows all too well that you will either loose or break the one pull ring you get with a kit of 6 or 10 restraints. Extra replacements are expensive, these can be made for pennies while the official ones…
A simple 20 slot holder for AAA cells. Designed to be strong and sturdy yet simple. Many of the other versions similar to this one are a little tight when using rechargeable cells. This one provides a nice fit on Ikea Ladda cells.
A quick traffic wand for the pelican 3310 or 3315 flashlight. There is also a shorter version to turn your light into a small lantern for power outages or camping. Best printed in PETG if you intend to leave it in your vehicle. Use orange…
A remix of LooseLunch's Williams Screwdriver Wall Mount so it is now compatible with the Skadis Wall system. Print with at least 5 outer walls and supports for maximum strength. If you like this remix please like and post a make. Thanks
Quickly convert your flashlight into a headlamp or mount it to your helmet. All you will need is two zipties and possibly some double sided tape. I suggest using a quality double sided tape like 3M's VHB and UV resistant zipties. If you…
Some simple tags that use 2" x 4" labels to mark the filled date of your gasoline. Print in what ever filament suites your needs. PLA is not recommended as it may warp in the sun or heat of a vehicle. You will also need a 2" x 4" label…
A plastic Crowsfoot wrench for low torque applications. Uses a ½" drive ratchet Non marring for those softer fittings that are easily damaged by using pliers or pipe wrenches. Works on some clean out plugs Printed with 10 outer perimeter…
A simple two piece dog tag with a paw print on one side and your contact info on the other. Simply edit your information on the one tag and then print both halves. The raised text allows for an easy color change if you desire. All you…
Fits the 2422/2424/5400 Series of Dual-Light flashlights manufactured by Nightstick. Prints with 3 walls using a standard .4mm nozzle. Prusa orange PETG works well for this print. will fit other flashlights with a 46mm head diameter.
A simple sew-able label for soft first aid kits. Simply print as desired. Sew in place and your done. I was able to pass upholstery thread through each hole 3 times so there should be no risk of it falling off. As always if you found this…
Simple screw on clamp to hold AA or Cr123 cell flashlights. Also works well for other round items like broom handles. Print in PETG or ABS with the recommended settings for your filament. PLA is NOT recommended as it will deform under…
A quick printing holder for the Streamlight 4AA models to attach your light to any hard surface using a screw. I recommend at least 5 outer walls so the top portion prints at its maximum strength. Some supports will be required. The…
A quick printing holder for the Streamlight 4AA models to attach your light to the Multiboard Wall system I recommend 5 outer walls so the Multiboard mount prints at its maximum strength. Some supports will be required. The flashlight fit…
A stronger remix of the Skadis Tape Roll Holder. The second row of pegs to the bottom to make it much more stable. Some supports are required but they are minimal. As always if you found this model useful please like and post a make. Thanks
A quick printing holder for the Streamlight 4AA models to attach your light to the Ikea Skadis boards. I recommend 5 outer walls so the Skadis clips prints at its maximum strength. Some supports will be required. The flashlight fit is a…
A remix to allow the use of the alternative pocket clip. A simple box design for your Convoy T6. This design allows the use of the standard and alternative pocket clips offered by Convoy. There is enough play to store the light with the…
These are all currently available results.
