Counting matching models…
I needed a simple case for bluetooth proxies. As I have poor signals, I wanted to place the antenna as far from the noisy/interfering electronics as possible. I do not need any of the pins, so they are not exposed. The case is snap-fit,…
Larger versions of the Ratrig vcore4 "Electronics Wire Clip" to accommodate more cables
This is a wall mount/holder for a vacuum cleaner tube/nozzle. You probably do not need this unless you have a central vacuum cleaner, where there is no “natural” place for storing the tube/nozzle. The holder comes with a backplate to…
This is a vertical wall mount for Sonos Roam, inspired by some great designs such as https://www.thingiverse.com/thing:4867644 or https://www.printables.com/model/380346-sonos-roam-wall-mount. Unfortunately those did not fit my needs, as…
A DIN rail mount for an SSD and the excellent heatsink-turned-into-case from PiHut (https://thepihut.com/products/aluminium-armour-heatsink-case-for-raspberry-pi-4), for Raspberry Pi 4. Needs the DIN rail clip from Voron. Comes as two…
Dropped a box of abt 900 washers on the floor. Manually re-sorting was not fun at all, so I printed these simple sorters. There are six sizes of washers in the box, so I needed 5 sieves. The file name describes the hole size in the step…
Mount for attaching a Samsung Galaxy A9+ besides a printer. Also, see https://www.printables.com/model/1712443-detachable-adapter-for-4040-or-3030-profile-for-th
A skew calibration square that has guides for the caliper jaws to make the measurements more consistent. I use this together with the https://www.printables.com/model/1342524-leveling-guides-for-a-caliper
2x4 holder, but takes some extra space from the right, so the correct designation would be (2+)x4 slots. Could be shortened to 2x3 or even 2x2 possibly. I used this in Ikea Metod drawers.
Led strip mounts for mounting the Philips HUE led strip behind an L profile, for a few different mounting angles. The dimensions used for the strip are:
Vcore 4 is using long screws as the shafts for the belt bearings near the motors. During installation and maintenance these screws are held in place by friction on the screw head, i.e. the counterbore is tight. This is somewhat sensitive…
Knob for a ball valve. The valve shaft is 8mm in diameter, with a 6mm thick flat. Heigth of the shaft is abt. 3.5mm. The knob is 30mm long and 12mm high. To prevent backlash, it is important to get the flat accurate. The flat inner…
For tuning the belt tensions, it is possible to measure the self-resonance frequency of a belt with a known length. These guides help center the toolhead, so that the belts left and right of the toolhead, in front of the gantry, are the…
This model is inspired by the excellent GATS system, https://www.printables.com/model/1165578-gravity-assisted-tensioning-system-gats-for-v-core. I wanted a system that would tension all the four belts at the same time, and also add a few…
Mount for Euclid for the Ratrig toolhead beta 2. To fit this, you also need a new front piece for the toolhead, i.e. one that does not have the Pinda mounting tube. The new front piece is included. I made this to make the head lighter,…
Blade guards for a generic 60mm hole saw set and the Bosch 80mm set. Push on, pop off. Blades rest against a flat surface, which should help keep them in place. The mid tube guides the center drill bit to make it easy to push the guard…
I try to reduce the sharp turns in the (reverse) bowden to minimize drag. To that end, I use these guides to allow for a smooth path while using the BTT SFS2, mounted with the nice…
Integrated BTT SFS2.0 mount in the right-hand side shelf in the back of the printer. Depending on your electronics panel, the mounting hole nearest to the front of the printer might not be in the correct position (it is not for me at…
This is a replacement Cable Entry Cap for the Nevermore Stealthmax air filter. The original cap does not fit a microfit3, at least not when comparing it to the Molex specifications: the slot for the locking tooth is too narrow. This fits.…
A dock to go with Ratrig toolhead beta2 and the front piece and mount in https://www.printables.com/model/963737-mount-for-euclid-probe-and-a-new-front-for-ratrig. The dock is now thicker, so that the lead screw bearing actually reaches…
A minimalistic version of a squarish plant saucer. Printed in vase mode, and the corrugation makes it a bit sturdier. Seems to hold water, but check before use. 0.4 nozzle, PLA.
A fast-to-print, low filament use test model to see an overview of IDEX head alignment across the bed. The model consists of two 0.2mm layers. There is a bottom matrix to be printed with one material, and the top with another. Bottom…
A replacement shade for the Philips Hue Explore floor lamp. Seems you cannot buy just the shade, so the alternative option would have been to buy the whole lamp. The existing shade holder mechanism keeps the shade in place. Printed in…
A pass-through cap that allows you to pass an EU power cable neatly through an 18mm panel, such as the wall in Ikea cabinets. The difference to many other passthrough mechanisms is that the cable exits from the side. This allows for easy…
A clip to prevent the solder wire from unwrapping. Also reduces the need to touch the solder wire by hand, which is a bonus if you need to handle leaded solder. I printed w. ABS, but others probably work as well.
Rartrig V-Core 4 and 3 use an aluminium support bar for the x gantry. Changing the alu extrusion to a square tube made of titanium reduces the bimetallic bend. When installing the ti tube, something has to keep the nuts in place when…
A mount for using a 10.9 inch iPad at the side of a printer, including Ratrig V-Core3 and V-Core4. The mount attaches to the vertical extrusions with a single M6, and the tilt can be adjusted. As the fixing point is near the center of…
A simple wedge to put the macbook on, so that the macbook display will line up with the main display.
Mounts for temperature sensors: 3mm thermistor for the 2020 extrusion (updated model with less blocking of the extrusion surface) 1.2mm thermocouple for the 2020 extrusion 1.9mm or 3mm thermistor for the Rapido hotend: The mounts for the…
Mounting brackets to mount the 1 meter long version of the Blazecut tube. Tries to lift the tube near the ceiling and close by the extrusions, so that it would minimally interfere with the umbilical. Also, the brackets should keep the…
In the series of things you cannot live without, here is the ball sorter for the board game Mandamina. With this you can shave several seconds from the game preparations. The device fits in the original box without any modifications, you…
While neither Miele nor Siemens support it officially, it seems possible to stack a Miele tumble dryer on top of a Siemens washing machine. That works even when using the Siemens stacking kit, the one that has a built-in shelf . The…
I needed to adjust a Fenestra sound-proofing door that had the lock-side bottom scraping the doorstep. Since the frame was fixed with PU, the best option was adjusting the hinges. Unfortunately, the hinges do not have a built-in mechanism…
These are all currently available results.
