Counting matching models…
This 1x1 gridfinity module holds a stack of 20 6x2 magnets inside. Roll the thumbwheel and one magnet at a time is delivered to the top tray. You can operate the magnet server with one hand. There are interior compartments, but if you…
All the information below and more can be found on the Tentacle System Home Page : https://3ddoodle.com/tentacle-system/ ------------------------------------------------------------------------------------------------------- This support…
This 2x2x5 Gridfinity module holds a Milwaukee M12 tool standing on the battery. Many of the M12 tools are balanced well and can stand on the battery end. The tools fit snugly. The soldering iron can be used hands-free and remain stable…
This 1x1 Gridfinity module holds a Swiss Army knife vertically to minimize its footprint. The square inside is 22mm which is wide enough for regular and narrow knives. Prints easily without supports. Based on the Gridfinity System from…
This 1x1 Gridfinity module is 3u high. It holds four 3g tubes of superglue, two with the lid down and two with the lid up. Opened tubes should be stored lid up so they don't leak. This module is designed without any through-holes, so if a…
This clamp holds fabric while you hand sew. Then you can slide the clamp out from under the threads and pull them tight. Clamp the next section and continue. The comb helps to keep stitching evenly spaced and helps prevent the fabric from…
This 1x1 Gridfinity module holds a pair of glasses. This is also a taller version for wider glasses . The glasses are balanced over the center of gravity so it doesn't fall over. It was designed using a coil to produce a helical path that…
This 1x2 Gridfinity module holds a stack of 40 6x2mm magnets inside. Roll the thumbwheel and one magnet at a time is delivered to the top tray, always in the same polarity. You can operate the magnet server with one hand. There are…
This is a Multiboard snap that provides a Tentacle System base. It prints without supports. The Tentacle System allows you to create ad hoc stands and holders using a variety of connectors and grippers. This part lets you attach those ad…
This device serves up 6x2mm magnets for use with Gridfinity baseplates and modules. They are always served up in the same orientation so their polarity is always the same. This helps avoid gluing magnets in the wrong orientation. There is…
This is an indoor golf disc. It is about 78mm in diameter and weighs about 14 grams in PLA. This disc is also found in the Disc Library here: https://smalldiscgolf.org/disc-library/#sabre where you can also download this .step file and…
This is an indoor golf disc that also works well outdoors, such as in a backyard course. It is about 80mm in diameter but less than 8mm high. It weighs about 14 grams in PLA. If you put some spin on this disc it is pretty stable. This…
This 1x1 gridfinity module holds a 35mm flashllight vertically. Prints without supports. Based on the Gridfinity System from Zack Freedman: https://thangs.com/designer/ZackFreedman https://www.youtube.com/c/ZackFreedman License: CC…
These are 1x2 gridfinity modules. Their function is to be an angled baseplate. They are low, but they will still raise up any module on them as well as angling them forward. There are versions with angles in 5º increments up to 20º. This…
This device serves up 6x2mm magnets for use with Gridfinity baseplates and modules. They are always served up in the same orientation so their polarity is always the same. This helps avoid gluing magnets in the wrong orientation. The…
This is an indoor golf disc. It is about 70mm in diameter and weighs about 5.6 grams in PLA. This disc is also found in the Disc Library here: https://smalldiscgolf.org/disc-library/#flexie where you can also download this .step file and…
This 1x1x2 module uses a standard 32mm binder clip as a vise. One arm of the binder clip slides into a slot. The other is in an open chamber. The print includes a reversible spreading tool for compressing the binder clip to hold it open.…
This 1x1 Gridfinity module holds a wider pair of glasses. The stand is taller than its shorter version (shown in the second photo). The glasses are balanced over the center of gravity so it doesn't fall over. It was designed using a coil…
These are 1x2 gridfinity baseplates. There is one flat one and the rest are at angles, in 5º increments up to 20º. This can help accommodate a leaning surface, or it can point the gridfinity module at an angle. For example, this lets…
This 1x1 Gridfinity module holds a Gerber Suspension multitool vertically. Prints without supports. Based on the Gridfinity System from Zack Freedman: https://thangs.com/designer/ZackFreedman https://www.youtube.com/c/ZackFreedman…
I have a 27" iMac. I wanted a cover for the built-in camera. The back of the iMac is curved. This cover fits that curve nicely. Mine has googly eyes. I think it works better that way. I printed mine in black so it would fade into the top…
There are two different solutions in this set. An adapter that goes from the smaller sized port that is already on the bandsaw to a shop-vac. A drop-in replacement for the original dust port. Both of solutions accept two different sizes…
I made ridiculous demands in my 3D model. Shapes, positions, and angles: they are unconnected, floating, oblivious. Ingredients for making spaghetti. Then I asked PrusaSlicer to create organic supports for it. A list of pointless todos.…
This 1x1 Gridfinity module holds three scripto lighters vertically. The model in the photos was printed using Eryone tricolor filament (black/purple/blue) using my spool rotator: https://www.printables.com/model/523118-spool-rotator The…
These are 1x2 gridfinity modules. Their main function is to be a tall, angled baseplate. But, they also have a cavity inside for storage. This can be useful when using gridfinity for tool holders, or a vise or light, but also want to have…
These Tentacle System components work with lego bricks. It includes a base and a grip. The Tentacle System allows you to create ad hoc stands and holders using a variety of connectors and grippers. This part lets you attach those ad hoc…
This allows you to attach two honey bottles so the contents of one can flow into the other without making a mess. It has arrows around the outside to indicate which direction should be placed downwards. The inside is designed to keep the…
These are scale models of horizontal fences and gates I make for my clients. They are all created at 1:25.4 scale: 1 mm in the model represents 1" in real life. The lumber is all nominal 1x1s, 1x4s, 1x6s, 2x4s and 4x4s and the fence…
These circular arrays of magnets on the two pieces repel each other. It isn't possible for static magnetic fields to float stably, so it always finds a point where the edges of two magnets connect and the others repel each other. But,…
I was gifted an M12 jigsaw with no base. It had rubber attachments on a jigsaw blade shank and was apparently adapted for use in the massage industry. Ouch? I made this new base for it and then found that it was hard to hold a nut inside…
These are scale models of fences and gates I make for my clients. They are all created at 1:25.4 scale: 1 mm in the model represents 1" in real life. The lumber is all nominal 1x1s, 1x4s, 1x6s, 2x4s and 4x4s and the fence boards are all…
This vase was formed by creating a sinusoidal surface and thickening it to a few millimeters. Then I repeated it in a circular pattern 30 times. They overlapped in the model but had very deep shallow angles where the individual waves met.…
This is a Honeycomb Storage Wall unit that provides a Tentacle System base. It prints without supports. The Tentacle System allows you to create ad hoc stands and holders using a variety of connectors and holders. This part lets you…
This Tentacle System kit includes a baseplate that fits inside an Altoids box along with parts needed to create a camera or webcam stand. In addition to the base, there is a 75mm straight extension and a ¼" threaded grip to hold a light…
This small bracket neatly holds a dremel tool either by its collet or by a tool. I recommend you screw it into a stud and not just wallboard. Prints easily without supports. I did mine in PLA with 6 layers for a solid print and it is more…
This simple 1x1 base allows any 1x1 Gridfinity module to be used alone. For a fancier 1x1 base, try the vanity base here: https://www.printables.com/model/511814-gridfinity-1x1-vanity-base The example was printed in Eryone Red/Green/Blue…
This hobby knife holder has two important features: * The blades point down for safety * You can see the blade tips so you can choose the one you want It holds 12mm or smaller tools. To print this you should use automatically generated…
This Tentacle System component grips a figurine for painting. You can use any tentacle base, but the Pill Bottle Weighted Base is great for painting figurines. A 7/8" or 22mm O-ring in the groove around the bottom makes it easier to use,…
This bar holds six router bits with ¼" shanks. The bar flexes so they can be removed and inserted more easily, but then clamps down for a solid hold so they never fall out.
Update: I've centralized most of the information in a new web site here: https://3ddoodle.com/spool-rotator/ I like tricolor, co-extruded filaments. I have been working on a way to rotate the spool so the filament twists as it is fed into…
This kit includes bases, grippers and extensions, all equipped with a means to attach a zip tie. Cylinder Clamps There is one base and one gripper that accept two zip ties and look like the letter Y. These are designed to attach to a…
This tall vase is made of elipsoids and overlapping coils. The coils are just at the same level as the outsides of the elipsoids so they seem to dive in and out of the vase. It was printed using my spool rotator (…
This vase has shingled curves around it and three vertical columns. It was printed in GNVTNTP silk PLA filament.
This vase captures a conflict between a coil and a sharp, curved gear. The coil succumbs to the gear in the middle. It was printed using my spool rotator ( https://www.printables.com/model/523118-spool-rotator ) using Eryone tri-color…
These small moths clip to branches or sit on flat spots as decoys to deter real moths from choosing that plant to lay eggs. There is no guarantee they will work, but at a-third-of-a-penny each they probably can't hurt the plants. I'm…
This 1x1x3 bin has space for up to 12 magnets to be glued into the bottom. Any parts that are attracted to magnets will be held inside the bin even if it falls over or is dropped. You can easily get them out using the curved bottom…
Lift your favorite 1x1 Gridfinity module up above the others by mounting it on this artistic, vanity baseplate. It uses organic supports between a round base and the upper platform which begins as a hexagon and ends as a square. Requires…
You slide one of the metal handles of a binder clip into one of these Tentacle System holders so you can use the binder clip to hold onto anything that fits. Binder clips have a lot of closing force. There is one model designed to hold a…
I use a few Milwauke M12 tools such as their driver and their stapler. The batteries are held in by two small plastic tabs that snap into small detents in the tools. Even a single broken tab means the battery can fall out during use.…
This vase is formed from many twisted elliptical columns that intertwine with each other. It was printed using my spool rotator ( https://www.printables.com/model/523118-spool-rotator ) using Eryone tri-color co-extruded filament. The…
These simple tools each hold a single 6mm x 2mm magnet. You can use a compass to determine the proper orientation for a magnet in each tool. The North side of a magnet's needle will point to the South side of a magnet held near it. In the…
You slide one of the metal handles of a binder clip into one of these Tentacle System bases so you can use the binder clip to hold onto anything that fits. Binder clips have a lot of closing force. There is one model designed to hold a…
These two Tentacle System models work the same but have different purposes. They both use 4mm hardware. There is an pegboard hanger that provides a base. It works with any size of pegboard hooks. It can be attached to many different…
This 1x1 Gridfinity module holds a 100g Toblerone bar vertically in its triangular box. Why would you need to hold a Toblerone on your desk? Really? Is that even a question? This was printed in Gold/Blue/Fuchsia coextruded filament using…
This is an IKEA Skådis hanger that provides a Tentacle System base. The Tentacle System allows you to create ad hoc stands and holders using a variety of connectors and holders. This part lets you attach those ad hoc stands to a Skådis…
This is a multi-way connector for the Tentacle System . It has a ball so it can be a base It has a cup so it can be a holder It has a thin slot and retaining flange so it can be attached to the back of a binder clip. It has a long…
This tiny shield fits over the end of a USB cable to transform it temporarily into a thing that can be easily pulled through any obstacle course of cables and equipment. It prevents the square back end of the connector from catching on…
This is a simple vase, but it was printed with the spool rotator and tricolor coextruded filament: https://www.printables.com/model/523118-spool-rotator The photos are all the same print seen from different angles. Every angle is a…
This Tentacle System component screws into a 48mm pill bottle. Fill it with sand or water for a weighted base. This makes a great base for the Figurine Grip . You can learn all about the Tentacle System here:…
This is a collection of templates to assist in creating a horizontal fence by making it easier to keep the screws aligned vertically. It might seem like a small detail, but keeping the screws aligned is important, because if they are not,…
I bought a white Norton grinding wheel for sharpening tools and it came with a 1" bore and a series of concentric bushings. The problem is there is too much play in that stack of bushings and it is difficult to get the wheel centered when…
These are a stronger version of my original clamp pads . These stronger pads have a slot for a coin which distributes the clamping force more evenly, so it doesn't crush the pad. And, these are sliced with 100% infil and three perimeters…
UPDATE: here are stronger clamp pads that use coins as inserts. The ones below work for lower force applications. ------ Sometimes, clamps at the my maker space ( acemakerspace.org ) end up with missing pads. These replacements are…
This is simply a shim that is the same thickness as the DW746 table saw's riving knife. When you remove the riving knife and blade guard to cut a dado, put this in where the riving knife was. Then tighten the nuts again. This will keep…
These are all currently available results.
