Counting matching models…
Use at least 3 walls to get proper strength. You need support no matter what stance you print this. Tape does not give much weight to this holder, so you might want to print this vertically to minimize filament needed for supports.
This is a remix from @doc 's design: https://www.thingiverse.com/thing:2815022 I trimmed the back plate little slimmer, and made screw holes to fit Biltema perboard. I printed this with 4 walls and 4 bottom and top layers.Infill 10% is…
The blower is RYOBI ONE+ R18TB-0, and it's about 60 euros here in Europe. The blower has very good air flow but to get most use out of it, you really need some adaptors for it. This adaptor fits our camping mattresses and I'm sure all…
There are bunch of Oral B mods in Thingiverse, but nothing was just what I wanted, so I remixed @mschim design , which was a remix from @MakerMaik design. The fit is snugg (if your extruder is well calibrated) and keeps the chargers in…
Print, attach to pegboard, put drill bits into it, ready. Biltema pegboard holes are 4mm wide and 12mm abart from each other and it is sold in Scandinavia, but there are other brands around the world with same diameters.
Simple holder for safety glasses, modified from James Purcell's thing to fit Biltema pegboard. Biltema pegboard holes are 4mm wide and 12mm abart from each other and it is sold in Scandinavia, but there are other brands around the world…
This is a remix from @didymus : https://www.thingiverse.com/thing:2269374 I retrofitted his design to fit Biltema pegboard This takes 28 meters of filament (84g) and with layer height of 0.25mm and speed of 60mm/s is ready in little over…
My daughter wanted something like this, so I modified the original design from french to english. Printed at 100% and changed filament at 5th layer. With 0.2mm layer height and 60mm/s speed, this takes about 3 hours to print and requires…
This is a remix from this: https://www.thingiverse.com/thing:975039 and this: https://www.thingiverse.com/thing:1549700 My daughter (total book worm) got book themed x-mas calendar made by my wife and I was hired to make few things into…
I fixed few problems on original design. Wings will not break with light touch, bow and arrow fits in their place without sanding/drilling and I added number 1, but you can also use Dymo sticker instead. Use super glue to secure bow,…
I got tired of holding resin vat on top of sifter by hand very fast so needed to get some kind of holder for it. @alphaa had great design for that job, but I want to keep my table free from excessive clutter, so I remixed his design to…
Golden medal for the MVP (most valuable player) paintballer of the day, which also works as a key chain. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 10% Filament: any PLA 2…
RickBigriver's caliper holder was just what I was looking for, but I rather attach it with screws, so I modified it a bit. I also needed one for other caliper beside my other printer, that one is with smooth bottom and attached with…
This is a remix from Frank Lumien's great design (on the right in first picture, remix is on the left). I had bigger screwdrivers than his biggest holder managed to fit in, so I edited his design to make it a little bigger one. My own…
Yeah, it's a holder for Ryobi multitool. Four screw holes are in place for Biltema pegboard, but you can also attach this with wood screws to other surfaces. Biltema begboard has 4mm holes 12mm abart. Print instructions It's important to…
I remixed my own model to have totally different usage from Ryobi Shop Blower (R18TB). Wide nozzle helps blowing rubbish out from work tables or from the floor. I'm also using this to blow dust away from our terrace. Inside walls helps…
First of all, this was just a test if Bambu Labs X1 could do it and o'boy did it do great job. Main thing here is, that the first layer was printed with line width 0.25mm, with 0.4mm nozzle! If you do normal 0.5mm, you loose the details.…
I played 10 frames of bowling with a friend of mine and she totally beat my ass, so I made these for her to be able to celebrate her new bowling champion status. Me…I'm never going to bowl again :D My friend uses large earrings, so these…
I changed some dimensions from @Jody_T 's design to get more stable mount for GoPro 8 for VForce Paintball goggles. Also included place for nut in order to secure camera to the mount. You need to put M5 nut in the hole, which is tight…
My kid is sleeping in the next room from my gaming area and when ever I'm too lazy to put headphones on, he comes up and shh me. I printed this to remind me :) Einstein and hand are attach with double sided tape. Also in reddit I saw a…
This fits perfectly to Ryobi model OHT1845. It might fit some other models too, but not the ones with hedge sweep attachment in its place. Also blade guard needs to be off, but at least mine was so tight that it's impossible to use…
I modified barty3d's Ryobi tool holder to fit Biltema pegboard. This one is a bit tight for some tools but perfect for some. Oleost has better toolholder for some tools and it uses less plactic, but for example Ryobi P755 fits much better…
I use this socket wrench two times a year while changing winter/summer tires to our cars and always was searching where did I put it this time, so it was time to print it's own holder to my pegboard. This is intended to be used on Biltema…
This is a remix of a remix: https://www.thingiverse.com/thing:4232995 First @MightyMilky scanned the original side panel and made it ready to print then @PuddingBaer91 modified it to better fit elite controller (which does have large…
Simple pegboard holder for infrared thermometer. Biltema pegboard holes are 4mm wide and 12mm abart from each other and it is sold in Scandinavia, but there are other brands around the world with same diameters.
I do have a great memory, but I tend to remember the wrong things. Also, I have so many ideas and to-do lists that normal post-it notes looses their grip and falls down before I get to do the listed chores. Sometimes you don't have a good…
@Kolo23 's fine model converted to fit Biltema pegboard. Biltema Pegboard has 4mm holes, 12mm apart from each other and it is sold in Scandinavia, but there are other brands around the world with same dimensions. You can also attach this…
Friend of mine had a problem of loosing the table whenever she was alone in a restaurant and went to bathroom…she asked me to design this. I tried many different designs, but ended up with printing the sides flat to the print bed and then…
Friend of mine got the original keychain, but it had 2 small flaws in it. Regular 25mm keyring didn't fit into it and the letters wore off during normal use. He was still using it though, but as a X-mas present I made him a better one.…
Description Easter is coming and I wanted kids to get a new way to receive surprise chocolate eggs. This cute bunny is totally shocked if you take away it's precious egg…it's jaw will drop to the floor! But next night you can load a new…
All my solder rolls are 30mm wide and have 20mm hole, so this holder has room for 32mm wide roll and stub diameter is 19mm. This uses 6 grams (1.9m) of filament and is ready in 51 minutes when printed with skirt and speed of 60mm/s. You…
This fits disposable gloves box which is sized 113*43mm. I tried several brands and they all fit perfectly. Biltema begboard has 4mm holes 12mm abart. Biltema operates in Skandinavia, but there are other brands with same dimensions and…
This is minimalistic pegboard holder for staple gun with dimensions of 25mm wide and 80mm tall. There is 5 degree angle on the holder and little upper lip to keep the stapler in place with ease. This is intended to be used on Biltema…
Simple and minimalistic holder for 1/2 inch sockets. Biltema pegboard holes are 4mm wide and 12mm abart from each other and it is sold in Scandinavia, but there are other brands around the world with same diameters. Category: Tool Holders…
This is a remix from this: https://www.thingiverse.com/thing:4829889 I only changed holes to fit Biltema Pegboard. Only takes little over hour to print and uses 12 grams (4m) of filament. On the holder you can see two great printable…
You need a small burner to lots of things. Shrink wraps, removing paint, melting plastic, defreezing locks, wood burning, starting campfire, etc. This pegboard holder is made for Biltema branded small burner, which tank diameter is…
I just made small adjustment to fit A_Str8 design to Biltema pegboard. Original design is here: https://www.thingiverse.com/thing:4132596 Biltema begboard has 4mm holes 12mm abart. Holders are attached with screws, so they can take much…
3 different ways to put carpet knife to your Biltema pegboard. In Biltema pegboard holes are 4mm and 12mm abart. Biltema operates in Skandinavia, but there are other brands with same dimensions and you can also screw directly to wall.
Some printers have feets on their vats, so you can set them to any table surface, Phrozen sonic mini 4K doesn't have that and I always have trouble finding a good spot to lay it down between dripping leftover resin back to resin bottle…
I have Avalon Basic sights on several recurve bows but they keep breaking on one weak spot when people handle them roughly. Replacement part is not available and new sight package is 15€. So I modelled the part and fixed the weak spot and…
Do you even paintball bro? No seriously, if you haven't decorated your paintball bag...congratulations, you can still be classified as sane. But who want's to be sane today in this world, so print this Pew Pew -badge and put it to your…
This is designed to be printed with 0.42mm line width! If you are using 0.4mm nozzle, then 0.42 is coming out great and making strong prints! Also included is 3mf -file, so you can open this in Microsoft 3D Builder and easily change wall…
I first made holder for wire stripper, but then noticed that my ferrule pliers needs similar holder. So here comes double holder for electric pliers! drum rolls Included is also a file for single holder, if you thing you can go on with a…
I got tired screwing phone into the holder (see here: https://www.printables.com/model/80163-bike-holder-for-phone-and-drink ), so I needed something faster and easier. In to the rescue comes @azure93 who's design you can find here:…
I first made simple alteration to Droidski's design to fit this to Biltema Pegboard, but after a month of use, the lower thing holding the can in place, broke down. So I made the lower thingie stronger in this v2. For some reason I made…
I'm always searching for my hex keys (or Allen wrench or Allen key) so mayby this will help. Did you know in Finland we call hex keys "kuusiokolo", which translates to "six sides hole". Germans use the word "inbus", Italians call them…
I tend to need couple of smart device chargers in my workshop, both micro-B and USB C types, but the use is so random that I needed a holder for them and not taking the space at the power outlet. NOTE - this is for the europlug only!…
I needed pegboard holder for Ryobi One+ batteries and there were many great ones already made by different people, but I found @cregory83's most suitable for my needs. I simple changed hole sizes and locations to fit Biltema pegboard.…
I liked @eirikso's wall mount but needed to fit it to my pegboard. Important!!! Print this in the orientation that stl-file has, so layers won't separate while using the holder. I used 15% infill and that seems to be good amount for this.…
My original holder was nice, but torch is in such active use, I wanted to have a holder that makes taking the torch out and back in really fast. My torch is 27mm, but you can fit anything under 29mm into this. Collar is to guide the torch…
Sajmonn's awesome design fitted to Biltema Pegboard (which has 4mm holes 12mm apart). Acrylic paint set is sold in Clas Ohlson: https://www.clasohlson.com/uk/Sang-Acrylic-Colour-Set/34-9247 There are other brands that have same diameters…
This is a remix from msansjr's design to save some filament. Change the game of tic tac toe. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 10 Filament: any pla Notes: With 60mm/s…
I needed to get my TS100 soldering iron onto Biltema pegboard, so I made holder for that. I also added holder for soldering pump that is commonly sold in Amazon and other retailers. Also included is pegboard holder for my Ryobi battery…
Every time my kid asks if I can pump more air to his football, it takes me 20 minutes to find the nozzle. This holder takes away the searching! I'm not sure what the other two nozzles are, but they came with the bike pump. This is fast…
I almost thought that I'm getting old and my eyesight has impaired, but then realized that everything is just written smaller than what they used to be. If you want to see what instructions there are in the noodle can, you almost need a…
Dentist tool, also known as Sickle probe or Dentist Explorer is very important tool in a workshop! For example if you need to remove small and tight rubbergasket without damaging it, this is the only tool that can make that happen! Okay,…
It's just a way to recognize what keys go to what machine. I should just get a lawnmover robot but hey, there is no drink holder in those! This is made for Bambu Labs printer with AMS unit, but I'm sure it can be printed in other ways…
This is multimaterial print and included is good ol' STL -file and Bambu Labs -file with coloured areas ready. When printed 6 at the same time, you only use 20 grams of filament and tweeking purge amounts you could get couple grams away.…
I need small dust blower beside my resin printer to blow out any dust particles from resin vat and from the top of the screen before printing. This holder fits a blower that has a tube of 8.3mm or less. I included .3mf file if you want to…
I needed more of the 1x1 boxes for storing different sizes of small bolts. Manufacturer don't sell separate individual boxes, so…3D printer to the rescue! I actually made other size boxes too, but this has been so long in the draft…
I do have other holders for pliers like this one: https://www.thingiverse.com/thing:2983339 ...but I needed a holder for groove joint pliers that are in frequent use, a holder that hands the pliers fast and in correct orientation and…
We have 4 people in our family and we all have different favourite fast food restaurants. Instead of fighting or keeping score who got to decide last time, I made some magnetic labels to the wheel of fortune that @WillemvD made. He made a…
Turewell Water Dental Flosser does not come with any storage solution for replacement parts. This is remix from @DavidS 's model, which was made for different brand of flosser where accessory parts are a bit different size. I also added…
Are you working in home / telecommuting / remote working because of covid pandemic? Does your children ruin your Zoom meetings by running in and yelling while you are presenting next year's budget to your boss? Did you put post it -notes…
These are all currently available results.
