Counting matching models…
Updates 1/23/25 ** Created/differentiated a square vs rectangular shape designs (they are sorted in folders below). If you print the square version, it may not complicate scaling issues for you if you find that you have them. I recommend…
* Not only did I sand the edges when the print was done, but I also covered these in duct tape to protect the neck during use (it does pull against the neck). You could probably also use some kind of foam or felt and hot glue or something…
Created a 20 slot battery holder for BT2.0 1S batteries made by BetaFPV. There is some wiggle room built in for if/when the batteries expand a bit from use or heat. The slots are 8mm wide x 16.5mm length x 30mm deep . This was designed…
I noticed newer BOSS pedals made in 2024 can also contain a notched area for the 9v adapter. Some of the older pedals have the 9v plug floating, while some pedals have it justified at the bottom. I took the plate off, measured the notch,…
This is a remix for https://www.thingiverse.com/thing:4002006 Needed a skid that was taller to clear some screws that were sticking out of the bottom of a drone kit. The skid is 18mm tall and uses M3 x 12mm screws that go into your…
The Eibos Cyclopes Filament Dryer does not have a handle and it bugged me a lot that they didn't design something like this. * The holes are slightly smaller for drilling/sizing on your own ** You will need a small bit or an M4 tap bit to…
This mount is for a Porter Cable heat gun, model PC1500HG, 1500watt. I designed it to install on a flat surface for holding the gun at an upright 30 degree angle. You can make your own holes with a drill, or by transferring a pattern from…
It fits the following as I have tested on my own... D'Addario/Planet Waves cables with the Geo-tips Ernie Ball Users report it also fits the following... Some Fender cables (see user comments)
Designed a throw lever for a Barska Colorado 3-9x40 scope. I use this with a Daisy 880 shadow. I've created 2 versions for people to use, as I noticed the length of the longer lever was close to touching the stock end, so I really…
A unit circle made for vision impairment. I had a student who sometimes uses classroom tools for learning. I may upload a non-braille version. My student told me that you can paste braille dots on surfaces with some special tape. That…
*****Updated 12/1/20 : I created a version that is 20mm taller than the original hooks I created. Both versions are now here. I made a taller version because the X gantry was too close to the top of the frame when leveling the gantry. It…
The Beta FPV 95x v3 quad drone doesn't have a very stable battery holder. After a few light crashes in the grass with the battery coming dislodged, I was not too thrilled about the single velcro strip that holds any equipped battery. I…
I designed this because I needed more height for the shelf that is attached on my desk (I believe this is a desk from early 2000s. I needed a 1" extension. All you need to do is measure and buy the appropriate length screws to match the…
This is a remixed mod to an existing bracket that mounts a Pi4 on the Prusa MK4 with the GeeekPi case. I had to modify the original bracket because I installed a dual light bar kit from VoxelPLA and the original bracket caused the Pi to…
I made a D20 knob for my Elegoo Mars Pro table top edition printer. Of course it could be used with any resin printer. The square on top is 70mm square. Printed it with 4 walls, 25% infill. The print took right about 4 hrs for .2mm layer…
You really only need 2 of these feet. You can scale them up to nearly any size you wish. I don't see a need to make this larger/wider than 20mm in all honesty. The base models are only 10mm tall when laid on their side, but you can scale…
Ok. So here is a design for holding an Xacto blade at various heights. It's main purpose was made for work in clay, but you could adapt it for use with slicing other material, or marking things with a knife I suppose. Things to keep in…
Recommended settings… Print with the flat side down, use supports in the flat screw areas (the corner screws), it's not necessary to use support on the inner screws. 3-5 outlines/perimeters 5 top + 5 bottom solid layers 20-30% infill (I…
I created this template to help position a small pilot hole when installing a 9v Fishman Fluence battery charger into a back plate on a guitar cavity. I've found myself trying to eyeball the position and have messed up one of my guitars…
The bracket is 4mm in thickness, by 35mm tall. Designed to use with #6 screws that are 1" long (this will go great into ¾" wood, as this what what I used it for). You could certainly tap them wider if you need to use different hardware.…
**** Update: I created a version for 2 pin Fender / LTD locking tuner style *** Created this model because I am planning to sell some of my tuners that I swapped out. I wanted to create a better way for shipping tuning pegs safely in the…
Designed a back plate for the Solar A1.6 series guitars. It may fit other A models, but I'm not sure (I own the A1.6 Wop+, A1.6 TBR-27). It might strictly fit any A series model that has 1 vol + 1 tone + 3 way blade switch. I'm not sure…
The extensions that this bracket were created for are found on Amazon here.... I included images of how you could add supports. I flipped it and added support underneath where the arches would be. Although I have had zero movement with…
I disliked the idea of a snap case, knowing that plastic would degrade over time, causing a lid to not close anymore, so I designed one for use with small magnets. Seems like it will fit about 6-7 floss picks. The magnets are 4mm diameter…
These are all currently available results.
