Counting matching models…
My little brother wanted a shelf next to the sink in the bathroom, but he didn't want to ask our parents for permission to drill holes in the walls, knowing they would most likely say no. So I designed this shelf to use the 0.75" x 3.65"…
I couldn't find a body kit for the Nerf Stryfe that I liked so I designed my own. There are two versions of the main body. “Body” is as pictured, and “Body2” has thur holes where the indentations are. You will need supports for the…
Introducing the SleekSpace 3D Shelf: The Ultimate Bathroom Organizer! Elevate your bathroom experience with the SleekSpace 3D Shelf – a marvel of design and functionality, now optimized for your bathroom space. This cutting-edge shelf,…
I needed a new case for my phone but I didn't have any TPU on hand, I did however have PETG, which is kinda flexible. I remix the “Samsung A52 bumper corner case” by Scav. There is a optional US Flag pattern on the back of the case as…
Tail light lens replacement (with alterations) for 1967-1972 Ford F-Series Trucks and 1967-1968 Mercury M-Series Trucks. I recommend printing with transparent/translucent PETG (red and clear), 0.18 mm layer height, 22% Sprial infill, one…
I designed this simple “pinewood” derby car with angeled axle holes as described in Mark Rober's video: You shouldn't have to bend the axles. If the holes are too small when printed, be careful when drilling them out so as not to change…
Remix of the EQUALIZER half-dart mag by devilZmods. Holds ~25 half darts. You don't need supports, however, I recommend printing the follower in the orientation as shown (w/ supports) for smoother operation, as the layer lines will be…
A direct replacement for the Lexus LX450 or 95-97 Toyota Land Cruiser driver's right HVAC vent to install 52mm gauges without obstructing air flow. Remix as needed for your gauge. I recommend black ASA & supports.
Use two M4x12 button head fasteners to secure the rail to the handguard. Use two M4x40 socket cap fasteners to clamp the handguard to the blaster. Print with Arachne wall generation & supports.
I wanted to give my 1969 F-250 a dedicated turn signal without taking away from the classic tail light, and then I thought, you never use your reverse indicator and turn signal at the same time, so why not make them into one light? I…
From Left to Right (Mostly): https://a.co/d/0fd3m60b https://www.harborfreight.com/12-in-fast-adjust-water-pump-pliers-56749.html https://www.harborfreight.com/10-in-fast-adjust-water-pump-pliers-56748.html?_br_psugg_q=doyle+pliers…
I have a mix of Icon & Tekton crowfoot wrenches, so this was designed for my set.
My original design for my LX450 / FJ80 Front Bumper. I fabricated the prototype and was getting ready to test it on the trails when my 1FZ-FE developed rod knock. It will be some time till I get back to this, and during the fabrication I…
Do you have an aftermarket head unit in your Lexus LX450 or 95-97 Toyota Land Cruiser and no longer need the OEM clock? Why not replace it with a coin slot? Black ASA & Supports Recommended
A battery box to replace the stock on the XShot MPP AEB. Attaches with the printed nut, use 3/4 or 19mm hex to tighten. Designed for the existing battery, the XShot MPP AEB comes with. No supports needed. Print the nut and battery pack…
Print in a temperature & gasoline-resistant filament (PA6/12, PPA, PPS, etc. GF/CF filled) @ 100% infill, 0.16mm layer height, & 4 walls/perimeters. No supports are required for the Elbows if properly oriented (see attached image #3);…
Print Settings: Print w/ Normal Supports, 100% Rectilinear Infill , 2 Walls / Perimeters, 0.2 mm Layer Height, Arachne Wall Generation, Oriented as Shown , in ASA. Mill Operations: Op1, Using 0.200" deep soft jaws, skim 0.050" off Sides &…
Are you looking to add an aftermarket stereo with a rear USB input to your 2nd-gen Mazda6? Do you want to avoid making permanent changes or drilling holes? This mount replaces the 12V cig port in the center console. I designed it around…
Red: https://www.harborfreight.com/14-in-38-in-and-12-in-multiple-rail-socket-tray-sae-70025.html Black: https://www.harborfreight.com/14-in-38-in-and-12-in-multiple-rail-socket-tray-metric-70024.html
These are all currently available results.
