Counting matching models…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. Teal bits Green bits Gray bits Black bits Red bits Blue bits This is meant to be printed as separate parts (like the original model) and not…
Red bits Gold/yellow drone bits Black/Dark Gray bits Lighter Gray bits Outer olive/bronze bits Painted in PrusaSlicer 2.4.0-beta1; won't work with version 2.3.3 or earlier. Simply load up each .3mf file as a project into [at least]…
Red bits Purple/Blue bits (carbon silicate laced armor) Black bits Light Gray bits (Silk) Dark Gray bits Slices better with PrusaSlicer 2.4.0 (rather than 2.4.1 or 2.4.2-rc2) Simply load up each .3mf file as a project into [at least]…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. Dark Gray bits Light Gray bits Just one of my earliest MMU edits that I never got around to uploading. Only MMU edited parts were uploaded;…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. Gray bits Black bits Copper bits Blue window bits Yellow engine bits Mostly followed Martin's CAD on Youtube for colors, but it's not like…
Gray bits Gold bits A few Black/Dark Gray bits A bit different from my usual approach. This time using [alpha version of] PrusaSlicer 2.4.0's new color painter feature rather than split up .stls through Fusion360. Simply load up each .3mf…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. White bits Black bits Grey bits Blue engine bit In my case, I only had white filament in PETG while my black/grey/blue is PLA and they don't…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. -Lots of blue windows -Yellow and black on the missile launch doors (reused from BC-304) -White lettering on the front's sides -White…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. Dark Gray bits Light Gray bits White bits Blue bits Yellow bits I printed mine at 120% with plenty of room on the build plate. I think 145%…
Split up specific stls for printing with different colors in case you have an MMU or equivalent. -Blue windows -Yellow and black on the missile launch doors -White lettering on the side -White parts on the hangar doors and floor -Blue…
Opted for a 10-pack of double-nylon/brass(?) cleaning brushes on Amazon for a dozen dollars instead of a 10-pack of pen brushes for eight bucks; think of all that extra brush value. Nylon to not wear the brass nozzles and the brass for…
You can go a little bigger but 280% is a nice round number for about as big as you can print the Donny without extra splitting up of parts on the Prusa XL. Ends up ~38in/97cm long. IIRC it took took me almost a month to fiddle with things…
Picked up a Last Gen food dehydrator during a nice deal. Instead of cutting up the trays I'm using them to hold/dry desiccant beads and using these interlocking walls for drying spools. The Last Gen seems to be a cheaper clone of the…
Reuse a Dell P2317H monitor stand (or similar) with any VESA 100 capable monitor. You will have to remove the stand's plate's plastic covering - just remove all [very short] screws, remove plastic, then screw the plate back on. It does…
I needed an adapter that seems to not exist in single part form. A little bit of thread tape on the maleNPT end helps but wasn't necessary. No barbs on the hose half didn't cause any issues. Modeled with a flat bottom so you don't need to…
For whatever reason I could only find the larger 8mm bore/endo scope cameras that work with a Windows PC on Amazon. Everything else was either a standalone tool or only worked on smartphones \_(ツ)_/ So the camera cavity was enlarged for…
Each prints in two half-pieces, in case the wires have already been run through the hole(s). wallTunnel.top.stl goes into the hole in the wall wallPlate.top.stl holds the M25.4 rubber grommet by its inner groove and slots into the…
Nextruder demands pliability🐙! Took this interlocking walls model and made it one single 360° piece without the interlocking for printers with big beds. Works with Last Gen food dehydrator or similar. Probably don't want to print it in…
I was asked for a stand for an antenna at 11" high that looked like an expanded hollow-point bullet and this is my novice attempt. Not modeled after any specific round. Print it either single or multi; not sure which wastes more filament:…
OUTDATED File. Left for posterity, but this feature is now officially in the slicer so this example is not as relevant; ignore it. Unofficial multi-color, multi-nozzlesize example using a pre-color-seperated Dragonite MMU model. Tool 1 -…
Have you ever wanted a scuffed door camera instead of giving your privacy away to Bezos and his Ring cronies? Well you're in luck! Buy a dome camera with 2-way audio, like this one from Amazon which this model is based on, cover it up…
Creative X4 DAC LED ring cover. Just toss it on, loose fit. Does not cover the LED under the knob so there's still some light. 2 perimeters, 4 bottom layers with the flat side down; 13 minute print. ezpz f3d file uploaded if you want to…
Someone asked for an example project with multi-everything and I obliged. https://forum.prusa3d.com/forum/original-prusa-xl-tool-changer-how-do-i-print-this-printing-help/use-case-study-multi-diameter-and-material-print/ Extruder 1: Pla…
These are all currently available results.
