775/795/895 DC Motor Mount
Printed in generic PETG at 0.2mm layer height without any supports, 5 perimeters, and 20 bottom solid layers. Write in the comments and post a make. Thank you and enjoy!
- Downloads
- 610
- Likes
- 58
- Rating
- 5
1,148 models
Printed in generic PETG at 0.2mm layer height without any supports, 5 perimeters, and 20 bottom solid layers. Write in the comments and post a make. Thank you and enjoy!
A plate for weighing down Lysel slatted curtains. Measurements: 89mm x 50mm
I needed a simple card insert for "Twilight Struggle," so I made my own. It fits 42-44 cards in Standard American size with premium sleeves (90 microns), measuring 27 cm in height so it sit flush with polish cardbox cutout of Twilight…
Wall mount shelf that fits a cable modem "Sagemcom WiFi Hub C2 - F@ST 3890V3 CHWU" The supports below the shelf doubles as convenient points to tie the cables to. The hexagonal holes in the shelf are for ventilation, as the modem has…
Using the original design (thanks to Irgendeintyp ), I turned it into a socket to repair the broken parts. In this form, the weights were reused by cutting the broken handles and trimming the edges. This saved printing time and filament…
This is simple housing for a Siemens Sirius ACT EStop that will fit on 4040 VSlot profiles on the Ender 3 and be secured by the sheet metal control board compartment. The two rectangular cutouts on the back cover are made to fit two WAGO…
Simple replacement ("upgrade") for the Ferris Wheel token in World's Fair 1893 . I've tried to copy the style you can see in the pictures in the Wikipedia entry for the original Ferris Wheel. Print instructions Resolution: 0.15mm Infill:…
Curved card tray for 63x89.5 cards. I decreased the size to 152x103x45 vs 157.1x115.1x32.5 size of the original. I really liked J erry's design but wanted a tighter fit on the cards side to side movement and taller. I tried increasing the…
(English below) Modell eines Audi Cabriolet (Typ89, Baujahr 1991-2000), entweder in der Ausführung "Serie" (seriennaher Zustand) oder “Tuned” (mit Tieferlegung und Rieger RS2-Frontschürze). Es eignet sich ideal als Schlüsselanhänger für…
I needed a way to attach the gold greeble "button" to the 89 Sabers Skinnyflex being able to remove it later with little work involved. This is designed to have a 6mm x 3mm magnet for the center. You need to glue the magnet in to where…
A 3/8" drive designed special socket for removing VW, Audi, SEAT, Skoda airbox studs, as a standard bi-hexagon socket does not accommodate the stud head. Printing Information. 0.20mm (QUALITY) layer height. 25% infill. 2mm shell thickness…
Mopar 3488995 COURTESY LENS 1975-1993 Door courtesy/interior lamp lens for: B-body 1975-1978 (CORONET, CHARGER SE) F-body 1976-1989 (ASPEN, VOLARE B-Vans -1993 G-body (DAYTONA/LASER) L-body (HORIZON/TURISMO, OMNI/CHARGER) J-body (LEBARON)…
No supports needed for ol' Bats when printing on an FDM printer :)
*** Thanks for checking out this model! *** If you appreciate what I'm doing, buying me a coffee would be a wonderful show of support! Good quality designs take time, effort, and CAFFEINE! ;-) And then check out my other models for…
This model is compatible with the lego system.
Mini version of the 1989 Batmobile from the Tim Burton movie With spinning wheels Support me on Patreon: Print instructions The parts should be in the best orientation already, but just in case I have included an orientation picture in…
I love the Open RC designed by Daniel Noree but I didnt just want the same car everyone else had. So I decided to design my own. And what car is more iconic than the 1989 Batmobile. Unfortunately when I deicided I wanted to design my own…
This is a 3D model of the LEGO Star Wars Blaster #57899 in minifig scale. I'm currently working on a human sized version similar to this design which is split into multiple parts small enough so they can be fitted on most of the common…
****Find all of my exclusive content on my Thangs.com profile **** Channel your inner vigilante with our 1989 Batmobile kit! The kit is roughly 9 inches (23cm) long and 4 inches (10 cm) wide. Shop the filament we used in this model on our…
>> This mod may void the warranty! << >> Modify the radio at your own RISK! << Order a kit: Purchase a kit here: https://forms.gle/EGKaYYa485J8wiMW9 Go here for details: https://github.com/N0BOY/FT891_powerpole Enjoy it! - Jason Wang,…
Also check this 2019 Godzilla: https://cults3d.com/en/3d-model/art/godzilla-figurine This is a 3D scan of a Godzilla figurine (1989/based on Toho Pictures’ Godzilla vs. Biollante) made with an Artec Space Spider by Laser Design. It had…
This model is compatible with the lego system.
Created GPS Mount after waiting for KTM Powerparts GPS mount (A61012992044) being on backorder. There are two file versions. One that fits the 890-R windscreen and the other for the S-model windscreen. The S-model version extends out…
This model is compatible with the lego system.
This model is compatible with the lego system.
I got the dark millennium falcon (75389) and wanted to mount it flat on the wall like my other version. They changed the landing gear on this set which did not allow me to use the existing mount design. This allows it to be mounded at…
This model is compatible with the lego system.
This model is compatible with the lego system.
Batman 89 - , Movie-Logo like seen in the first Batman Movie with Michael Keaton 1989. I created also the Breast Plate Symbol from 89, the Batman & Robin Logo and the Batman-Forever Logo.
This model is compatible with the lego system.
This model is compatible with the lego system.
18942 LEGO technic gear rack 14 x 2 with axle and pin holes
Petřín Lookout Tower, one of the most prominent landmarks of Prague, was built as part of the Jubilee Exhibition in 1891 as a loose copy inspired by the Eiffel Tower (at a ratio of 1:5). It is 63.5 metres high, and 299 steps lead to its…
Print 1 each as downloaded for the Left side and 1 ea (mirrored) in your slicer for the right sides. (probably in PETG if you're going to use them outdoors) utilizing the provided hardware that comes with the Yaseu FC-50 Tuner. Don't have…
Batman's signature weapon, the Batarang. This is based on Tim Burton's 1989 folding Batarang from the movie. This was my first time modeling with surfaces in Fusion360, it was a challenge, but worth it. Getting the lines to flow like the…
KTM 790/890 Adventure chain slack tool! Slide in from the back on the chain buffer till it reaches the front upper chain guard mounting point. It might fit the KTM duke. 38mm is how tall the actual printed part is off the chain guide. If…
This model is compatible with the lego system.
Fan Art Clock of Miss Minutes , a character in the television series Loki produced by Marvel Studios . You can use the clock as a wall clock and as a table clock. The clock has a size of about 155 mm x 170 mm x 26.8 mm. The dial has a…
The default holders for this set aren’t very good, so I made new ones You can also stack all the bits on one side, which leaves room for other bits on the right. I also included a version with the ½" bit holder in place of one of the 1/8"…
This model is compatible with the lego system.
este es un soporte para w702 de carpuride para montar la pantalla
I bring you the most faithful version of the Batman logo from the 1989 movie starring Michael Keaton. It's the logo that appears as the Bat-signal and also on the movie poster. It's practically a perfect copy. I also added two holes of…
This model is compatible with the lego system.
Tool to help check chain tension and wear as instructed in the KTM 790/890 Adventure owners manual. The extruded side is 3.5mm thick (middle of the acceptable range 2-5mm) and 25mm wide. The bottom is grooved to check chain wear and…
There are no wires to cut, splice or solder together to make a base. It is designed to fit on a 4 inch/10cm led display base. The printed shade sits on top of the base, it is not attached. Once you purchase a base (or make a base if you…
Replacement pulls to release the rear seatbacks.
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This model is compatible with the lego system.
This is a model of the small plastic grill clip used to secure the grill onto the front of various Toyota vehicles. Based on the description of the part it may also be used in the interior. The model isn't an exact copy of the original as…
This model is compatible with the lego system.
Simple wall mount to hang a FTX Tracer RC Car on the wall. Printed in PLA at a 0.28 layer height with 20% gyroid infill Should be compatible with the HBX 16889 RC Car as it is very similar. Potential for compatibility with other 1/16th RC…
This model is compatible with the lego system.
This is slim compact case for a ST7789 I2C 1.54" TFT Display Screen. The case was designed based on the measurements of this model I ordered from AliExpress. As with the other slim cases I've created the model's clearances are very tight…
1989 (Taylor's Version) Lithophane made in Lithophane Makers website Nozzle: 0.4mm Layer: 0.1-0.2 (Recommended) Scale it as you like :)
This model is compatible with the lego system.
1989 Batmobile, reduced to a small, clean object that keeps its main shape and character. Part of the Mini Cars collection — The model is simplified for a reliable print at a very small scale. Print tip: use a 0.2 mm nozzle for better…
I just picked up my fourth HF radio, a Yaesu FT-891 and I needed rails for it. These rails protect the front knobs and rear connections very well without adding alot of bulk. The slots on the side are mlok dimensions so you can add any…
update: I've made the license commercially available to you. I like to pay it forward as I have made my share of money off of free models. Anything that can potentially make someone's life or health better, I will release as commercially…
This model is compatible with the lego system.
This model is compatible with the lego system.
Here's a super handy dandy Batman 1989 Logo (you know, the one with Michael Keaton) candy dish bowl. Useful for putting stuff in! Please contact us if you'd like to have this printed for you! Check out more great home organization,…
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
You can find the BAHA BUG body here . You do not need to scale it up the 1/18 scale fits as in the pictures. I used 10lb velcro and you need to use it sparingly as it is quite strong. Body: Here Buy me a coffee:…
This is a remix of the race truck body by MarkerDave created for the WLToys K989 1/28th scale RC car. I've added some details to the body, closed the holes in the front and made it lighter. Width is 75mm. The body can be mounted perfectly…
This model is compatible with the lego system.
HueForge - Emblem des Fußballclubs VfB Stuttgart 1893 Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA BambuLab Basic Red Transmission Distance: 5 PLA BambuLab Basic Jade White…
This model is compatible with the lego system.
Based on this design from reddit! I used a piece of 110mmx40mm sandpaper and a couple of m3 screws. Does it work? Kind of… Is it cool? I think so.
A replacement battery cover for Denon RC-1192 remote. Printed in PLA, but I think that PETg or ABS will be good too. Print instructions Print Settings Rafts: No Supports: Yes Resolution: 0.2 Infill: 100% Filament: Any PLA
This model is compatible with the lego system.
Ersatz Gummipuffer Heckklappe am Megane 2 Coupe Cabriolet. Da dieses seid Jahren schon nicht mehr bei Renault verfügbar ist, habe ich selber einen Designend. Die Montage ist etwas unentspannt, da die Aufnahme sehr eng ist. Mit etwas…
This model is compatible with the lego system.
Batman 89 - Breast Plate Symbol, like seen in the first Batman Movie with Michael Keaton 1989. I created also the Movie-Logo from 89, the Batman & Robin Logo and the Batman-Forever Logo.
This model is compatible with the lego system.
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
As seen on YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
Optimized for 0.4mm nozzle. Print with PLA or PETG. Add brim if falls off the bed.
AEG Electrolux 8996470604712 Condenser Tumble Dryer Foot Visit the AEG Store Print instructions For optimal results, please adhere to the following recommended print settings: Filament Type: PETG. Print Layer Height: 0.10mm Perimeters:…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
I bring you the most faithful version of the Batman logo from the 1989 movie starring Michael Keaton. It's the logo that appears on the Batsuit and goes on the chest. It's practically a perfect copy. I also added two holes, approximately…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This is a self-designed body for a WL-toys K989 rc car. The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in…
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
I made this thing so it plugs into a breadboard. Then I added a deep box for it. In the deep box I use the standard M-F jumper cables. It snaps together no glue required. Can be opened up if you want to reuse the part Print Settings…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, please consider buying me a coffee , and check out my other models ! ********** [UPDATE Oct 25, 2023] Load tested to 63.6 lbs (28.9 kg), at which point the cam…
This model is compatible with the lego system.
This model is compatible with the lego system.