VW Bus Pickup Year 1968 Designer Ed van der Heijden.
VW Bus Pickup Year 1968 Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 210 Filament material: PLA
- Downloads
- 1,258
- Likes
- 477
- Rating
- 4.75
129 models
VW Bus Pickup Year 1968 Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 210 Filament material: PLA
Dimensions: 60.5mm x 47mm For multiple colors: 0.00mm - 2.00mm (green) 2.20mm - 3.00mm (yellow)
A case for the PCA9685 16-Channel Servo Driver board from adafruit and its cheap chinese clones (see note below). The bottom part comes in two versions: a plain standalone version and one with connectors for the fischertechnik…
See https://www.amazon.com/gp/product/B08CHCG42N/ref=ppx_yo_dt_b_search_asin_image
A simple case for a 16 channel servo motor pcb. I used one from Adafruit for my build. I printed it with 0.2 layer height and a 0.4 nozzle in ASA. But it should print just fine with any other material.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
The part number of the w639 glove storage compartment is A6396800291 You can buy a replacement compartment for roughly 120€ from ali express sellers or 250€ by amazon sellers. But we are here for nifty DIY solutions, right? This Repair…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
I didn't want to pay $200+ for a Sir Tools P234 arbor so I whipped this up. I sell these for $15 if you do not have 3D printing capability, but I am offering it (for NON-COMMERCIAL usage) here. That means you are not printing these and…
This is a modified lid for the PCA9685 servo driver case by juh , designed to accommodate a board with a taller capacitor. The case fits my board perfectly, except for the electrolytic capacitor. Therefore, I created a lid specifically…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
A rare piece of Eastern European automotive history — the ZAZ-968M, lovingly called Zaporozhets . Built in the USSR during the late 70s and 80s, this tiny rear-engine car became a symbol of simplicity, reliability, and pure character.
Stand for Ron Whisley's car in the Lego Harry Potter set "Privet Drive" 75968. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.20 Infill: 20% Filament: Creality PLA White Category: Toy & Game…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Lamborghini Miura Roadster 1968
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Gridfinty Bin for a Lego Brick and Axle Separator, Item Number 96874 I am in the process of organizing my son's Legos via Gridfinity bins. Since we are always losing his brick separator, I decided it needed a home. 1x2x2 bin. Stacks…
DA-968 is a cheap Chinese ultrasonic cleaner, but it comes without basket. So, to avoid metal objects to be in contact with the container and permanent damages, I made a little basket to fit in the container. Designed such that it doesn't…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
A model of a 1968 or "Toob" ACA hurricane & ACA HURRICANE 130 MK1 that can be put on a Lego axle (file is now fixed)
The Man From U.N.C.L.E. - Napoleon Solo (Robert Vaughn) and Illya Kuryaki (David McCallum) Pistols - 1964-1968 3D printable model.
Sci Fi Movies - 2001 A Space Odyssey - Space Station V - 1968 3D printable model.
Hammer Film Scenes - Dracula Has Risen from the Grave - The Staking - 1968 3D printable model.
The Thomas Crown Affair - The Meyers Manx Beach Buggy (1967) - 1968 3D printable model.
Needed a stand to keep servo driver board from flopping around. I will update this model as I get more experience with this board and using it in my projects.
Mr. Rogers' Neighborhood - Fred McFeely Rogers - 1968-2001 3D printable model.
The Thomas Crown Affair - Thomas Crown (Steve McQueen) - 1968 3D printable model.
This model is compatible with the lego system.
Printed with Prusament Jet Black 0.3mm no supports are required.
This is the second version of my take on classic Cadillac's vacuum manifold. The first version, while more dimensional accurate and closer to the original, is a lot harder to print and more fragile (see here ). What is it? The vacuum…
This is a recreation of the steering column cowl for a 1968-1975 MG Midget, which seem to be pretty hard to find these days. I based this model off of the cowl that I copied from my 1978. I referenced pictures of the earlier cowls and…
This converts your transaxle linkage to a thrust bearing design. Has been installed on our rally car for over a year and has been perfectly fine (printed in ABS - see more info in printer settings section). Installation instructions are…
This model is compatible with the lego system.
Hawaii 5-O - McGarrett and Danno - "Book 'em, Danno" - 1968 3D printable model.
Horror Movies - Night of the Living Dead Collage - 1968 3D printable model.
Ferdinand Porsche didn't like the cars in existence at the time so he built his own. We haven't built our own cars on our printers yet, but we can make replacement parts. Example: The Porsche 944 and 968 have a HVAC control that is…
The Thomas Crown Affair - Vicki Anderson (Faye Dunaway) - 1968 3D printable model.
The Man From U.N.C.L.E. - Napoleon Solo (Robert Vaughn) and Illya Kuryaki (David McCallum) Rifles - 1964-1968 3D printable model.
Iconic Movie Moments - 2001 A Space Odyssey - Hal's Lobotomy - 1968 3D printable model.
This is the original version I designed. For a much improved version, please have a look here . This is a replacement for the 1968 Cadillac vacuum manifold (5 port version) which is part of the climate control vacuum circuit and is…
Rosemary's Baby - Adoring the Newborn - 1968 3D printable model.
Dr. Who - The Wheel in Space - Cyberman - 1968 3D printable model.
1968-69 LOTUS TYPE 49B Winner, 1968 British Grand Prix, driven by Jo Siffert Jo Siffert after winning the 1968 British Grand Prix in the Rob Walker Racing Lotus Ford 49/R7. Jo Siffert debuted the brand new Rob Walker Lotus 49B, chassis…
Iconic Movie Villains - 2001 A Space Odyssey - Hal 9000 - 1968
Mount holds an MG-996R servo and a PCA-9685 PWM demultiplexer. It has holes for mounting on aluminum extrusion. The bottom servo sits in the housing (press fit) and the PCA-9685 attaches to the mounting posts with M2 bolts (10mm). Has…
Ford Mustang Fastback 1965-1968 Racing
Oil filters are only supposed to be hand tightened, so a PLA tool should be strong enough and you shouldn't need a ½" socket wrench. The main purpose of this tool is to keep the oil that remains above the filter from running down your arm…
1968-69 LOTUS TYPE 49B World Champion, Second, 1968 U.S. Grand Prix, driven by Graham Hill Graham Hill racing to second place at Watkins Glen. Graham Hill finished second in this Lotus 49B at the 1968 U.S. Grand Prix; after sharing it…
PCA9685 IC - 16-Channel High-Precision (12-bit) PWM Controller Holder
Dash Clock Housing with bracket for 1. Gen Firebird/Camaro. Bracket size may need to be adjusted to fit holes in center console. Screw sizes: Bracket to clock 0.4mm screw (hole: 0.38mm) Housing to clock 0.3mm screw (hole: 0.275mm), can be…
Since I did not want to pay 5€ for the new part or wait a week for shipping, this design was created. I hope it is of great use for you! I printed this part using generic PETG using 100% infill on my Prusa MK4S.
Iconic Movie Moments - Curse of the Crimson Altar - Lavinia Morley - 1968
Dr. Who - The Wheel in Space - Cyberman II - 1968 3D printable model.
Bottom for ultrasonic cleaner WK-968 It is a bottom that will protect your objects and your ultrasonic cleaner Made for the popular WK-968 Length of 16 cm and width of 8 cm
Replacement handle for Severin SM 9684 milk frother. Printed in PETG lying on the side with support
This is a replacement lid for Severin SM 9684. Created it for a friend who broke the original lid and it has been in use for more than a year now. Simple print without supports. PETG is recommended because of the better stability with…
Volvo Amazon blower fan, reverse engineered the broken old one. i also included the clip that holds the axle in place Print Settings Printer: Onyx one Supports: Yes **Resolution:** 0.1 Infill: 25% **Filament:** Markforged onyx black…
A Case to hold a PCA9685 board and an Arduino Nano.
decathlon not have parts for theyown stuffs so i print my own guard. Ref. : 968556 Square-shaft transmission, 7-9 speeds
MUSCLE WAGON!!!
Made from pics I found & liked. Models not perfect. Made to 150mm, re-size as needed. All made in STL & 3MF formats.
Faceplate for center console for rear view monitor.
no one ever made a model of my Falcon. I found an AI 3d CAD app, uploaded some pics and info on the look. It took a while to fine tune it, but turned out great I think. I'm still kind of new at this stuff, so I have printed about 5 of…
Print with any Outdoorfilament
Made from pics I found & liked. Models not perfect. Made to 150mm, re-size as needed. All made in STL & 3MF formats.
Apparently it's pretty common for these to break/wear out and nobody makes replacements. Instead you have to buy a whole expensive shifter assembly. The stock bushings are pretty anemic and there's lots of room so I made these longer and…
Replacement bug mesh behind the front grille for pre facelift. Replacement peice for VW part number 211259165. Print with TPU. 95A seems to work fine, but softer material might give better results for fitment. After printing all 4 main…
Jaguar e-type series 1 1961-1968 Racing
This Gridfinity 2x3 holder for the soldering tips and hot air nozzles of the Aoyue-968A solderingstation has four spare holes for additional soldering tips. It offers space for all four hot air nozzles. It was designed with the Fusion360…
My 1st Camaro from back in my "gearhead". Done with Autocad, then AI.
Headlight cover gear for 1967-1968 Chrysler 300. See photograph of original and printed gear to confirm the model. PLA works, but Nylon would be perfect. Printed in 2 parts and glued together.
There's a version with only more room for cables from below (not recommended), but also the most recent version, suitable when guiding cables from the back.
Porsche 968 Club Sport as a 3D Model. This design can be scaled to any size in your slicer. Print flat with ~5% infill to save material. Perfect as decoration. Category: Signs & Logos
If you find modern sewing machine's wheels too slippery, this model is for you. Well, this particular one is for Singer 14T968DC serger/coverstitch but its wheel is slippery too. Designed to print with slightly flexible filament I have,…
Uses #2 x 3/8 screws to mount the horn onto the chopper tube. Glue horn pieces together and chopper tube.
Hello everyone! Before you start witch hunt, calm down. I have Full licence for use Hueforge. Picture taken by photographer Karel Bucháček in Prague, during the August invasion of Czechoslovakia by Warsaw Pact troops in 1968.…
Lower mount is the same for both sides, front mount is mirrored
Joint pour les feux de bas d'ailes pour mustang 1968, ce joint n'existe pas d'origine Impression à faire en TPU
AC Door Actuator for 1965-1968 Ford Galaxie to use a more modern Jeep blend door vacuum motor. The original is no longer manufactured. This is to replace the vacuum actuator on the top of the factory AC Box which frequently dies as it is…
Mehrfachsteckdosenleiste für DIN 9680 Stecker. Ich setze diese Stecker im Wohnwagen ein, um den Solarstrom zu verteilen. Hiermit können jetzt zwei Kühlschränke und Außenbeleuchtung an der Außensteckdose angeschlossen werden.
Here is a battery door that will fit the Remco 1968 Rudy robot and Tin Man robot. It is made in 2 parts so that supports are not required. You do have to make your own metal battery strip that is about 7mm wide and 60mm long. I will…