Radiomaster BOXER Gimbal Protection
Protection For Radiomaster BOXER Controller Gimbals
- Downloads
- 531
- Likes
- 33
- Rating
- 5
Counting matching models…
Protection For Radiomaster BOXER Controller Gimbals
Some time ago I built a radio with a microcontroller and an FM-IC. I used an ordinary single-turn potentiometer to tune the frequency, but this did not work as intended. It was really difficult to tune in a specific frequency since the…
Alternative stick ends for the Radiomaster Pocket. Requires 2 M3x8 hex screws (on for each stick). Recommended to print with a brim, due to the small bottom area.
Knob for Potentiometer 3296 print with brim and disable detect thin layers.
I wanted a small handle for my Radiomaster Zorro to make it easier to carry when it wasn't in its case. There are two versions, one with holes to screw into with some M2 bolts and one for threaded inserts to go in. Both versions need 2 x…
This transmitter tray is designed specifically for the Radiomaster TX16S with a folding handle. All parts were printed in PETG for outdoor use: Satin sheet and Kores application 0.4mm nozzle 240C nozzle temp 90C bed temp 15% infill…
Knob for rotary encoder or potentiometer with 6mm shaft.
This is a simple TPU and hardshell case for the RadioMaster RP3 receiver to keep it safe inside your quad. The white inner part was printed using TPU, the outer shell was printed to using PETG.
Just a simple box to encase a potentiometer in and run a 5mm cable through. The lid is held in place by 4x M3x10mm screws ¹. The design is tailored for a layer height of 0.15mm. The holes for the screws are designed to be printed upside…
Radiomaster Zorro 18650 addon backplate holster mod. 2s2p 18650 to add your zorro battery capacity. Radiomaster Zorro lacks battery capacity. This helps a lot. You can glue the JST connector to this and make short balance lead.
This is the core of a variometer (also called a vario coupler) used in radios from crystal type to the early vacuum tube radios. I strongly recommend using a filament with no pigment, as many pigments interfere with RF signals. Print…
Basic cover for electrically isolating the backs of Alpha potentiometers. Designed particularly for the RV16AF-10-15K-XXX-3LA with a diameter of 16.5mm, but might fit other models.
Support la crosse technologie by Mika version 2
🇫🇷 Bienvenue à Paris! Welcome to Paris! The City of Lights' second landmark has arrived to MiniWorld3D's Wanderlust Collection on Printables, and it is also one of our most popular models, it has been downloaded and printed countless…
Print settings : 20% infill 3 walls
3D Model made for CAD. STEP/STP and STL provided. Model completely designed by me.
What it is A compact tool to determine angles. It also includes a 120 mm linear scale and ring gauges from 1 to 9 mm in 1mm increments (clearance designed is 0.1 mm). What to print There are three parts awaiting you, which can be printed…
Enter a new dimension of strategy with this 3D printable alien chess set . Unique horror design : biomechanical alien-inspired pieces including pawns, rooks, knights, bishops, queen, and king. Highly detailed : intricate textures and…
A Knob with knurled surface for Potentiometers with 6mm round axle. Slim 15mm diameter design. Prints well on an FDM printer with 0.1mm layer height. Ironing for the top surface is recommended. Print with shaft side downwards and colour…
New V3 with grooves for grip, angle markings, and modified dovetail channels! Slightly tighter clearances as well for less play. New V2 dovetail design added! Slightly flexible filament like PETG recommended to join the pieces without…
Knobs to use on a potentiometer to make it easier to use and give it a better look
-Material: ~ 2gm -Printing time: ~ 0.2 hrs -Recommended quality: 0.2mm -Dimensions: 22 x 22 x 12 mm If you like my work, don't forget to buy me a coffe ☕ You can also follow me on my social networks: Linktree: https://linktr.ee/Alitaria
Basic knob for a potentiometer on a MIDI controller or any other device. Has an inset slot on the top that you can paint. Dimensions: Inner Diameter: 6.5mm Outer Diameter: 18.37mm Height: 20mm
If you want to preserve the thread of your sticks : print this model !
BioMech Finger Prosthesis In 2011 I lost my left hand index finger in a work related accident... Bio Mechanical prosthesis are available... but very expensive…. So I decided to learn how to 3D print, I watch learning videos on YouTube on…
I didn't like any of the available Designs for Gimbal Protectors already uploaded on Thingiverse so I decided to design my own improved version. Some Key Features I found important: Both Gimbal Protectors connected in the middle, no…
I really like the zorro, but I needed something to protect the gimbals in my bag. So I whipped this together. It's a simple gimbal protector for the radiomaster zorro. Rotate 180 (print upside down) in your slicer to print without…
In 2011 I lost my left hand index finger in a work related accident... Bio Mechanical prosthesis are available... but very expensive…. So I decided to learn how to 3D print, I watch learning videos on YouTube on how work with AutoCAD…
D-Shaft Knob for Potentiometer/Rotary Encoder. Please remember to press Like if you download.
Hello! I made a simple potentiometer knob which I used to my project of audio mixer. Knobs are designed for 6mm potentiometer (hole is 6,2mm) it is sitting tight. ______________________________________ Cześć! Zrobiłem proste pokrętła…
Seii-Radiomaster_Boxer_Antenna_mod_adapter_v7_PETG - I took Bikernickmn's model and just polished that widest square piece because it was damaged in the original file. Also, whole file is not properly centered by the original author and…
A very easy-to-build Variometer for flight simulation. In analogy to my Airspeed Indicator it comes in two different versions: Either articulation by an SG-90 micro servo or with a 28BYJ-48 stepper motor (recommended). UPDATE 2024-12-21:…
🌟 Unleash Comfort: Radiomaster Pocket Gimbal Spacer Installation! 🌟 Ahoy, fellow aviators! Since embracing the Radiomaster Pocket, I've been soaring through the skies with joy. However, a tiny hiccup emerged – the thumb position felt a…
Fader para potenciometro deslizante Category: Music
Protractor made with all printed parts, no supports. The numbers and graduations are raised, ideal for 2 colour prints. I did mine by performing a colour change for the last two layers. I found similar models both here and on Thingiverse,…
This knob fits a 6mm potentiometer with a slotted actuator. Why yet another design? This design uses grip fins and a rib to prevent slipping and has a nice press fit that is tolerant to variations in print quality. I also include Step and…
Changes the Pocket to have Zorro switches on the SA and SD buttons. This files replaces the Pocket SA and SD switches with blanking plates. A hole is in the model for the Zorro RadioMaster switches that can be purchased as spares.…
What should've come with the radio... Features Fits both stock (10mm) and wider stick ends up to 16mm in diameter Full protection on toggles and dials Anti accidental power-on Customisable name plate area Recommended Print Settings…
RadioMaster Gimbal Stick Ends Set Unless specified and/or for heat set inserts, all stick ends are designed for flexible materials. i.e. TPU, TPE, etc. In case you need some clarification: M3: Radiomaster Pocket, Zorro, TX12 Jumper T20,…
This is a remix of the fader knob that I met here, since the original model was not suitable for mass printing, I had to simplify it a little for better adhesion to the 3D printer table and the absence of the need to print with supports.…
This is a simple potentiometer knob for diy electronics. It has a little line to indicate the value.
The spagettiometer measures out precise portions right from its own container. Just dial the lid to the 1-portion, 2-portion or 3-portion openings and shake out just the right amount of spaghetti, linguini, or angel hair pasta. It…
I needed something to make it easier for me to find a comfortable grip for the Radiomaster Pocket so I made these. Currently I have the no stick holder version available but I'll post other versions with the stick holders. I wouldn't…
Radiomaster Pocket screen mount for Emax Transporter 2 FPV drone goggle monitor. Wanted to be able to use it on my radio as the goggles done work with my eyes. Screen attaches with a standard ¼" tread 5/8" machine screw. See the attached…
Fusion 360 files released by request: This is an early release of version 2: Changes: Added 3D print support to the design. Some changes / forms created / added for future design changes. Left index – to convert to right hand use mirror…
This goniometer allows to accurately measure outside angles and rounded corners (fillets) of objects. With a regular protractor this is hard to do, especially for rounded corners. I designed and printed this to measure the angles and the…
Protect and mount your AudioMoth (a full-spectrum acoustic datalogger) in style. The AudioMoth Vault v3 is a highly-water-resistant case designed for field usage, which you can make with about $3 in materials, in under 3 hours, on any 3D…
Just a potentiometer model, nothing more created few years ago using solidworks 2019 .step file included .sldprt file included (solidworks 2019 or newer required / can be opened with fusion 360 as well)
2026-03-09: Added a larger variant with a compartment for the strap. Supportless print, you will need two M2x16 screws and nuts for the hinge. Based on my parametric case model .
Continuing with the scenic tour through Paris, here's the Arc de Triomphe! I have 2 options for printing: A complete model all ready to go, just glue in the bottom ring when done printing. Two pieces that you can print in different colors…
Gimbals and Screen protector for Radiomaster TX12. Added - bridge between the Gimbals Guard - 2 x Antenna mount Recommend TPU-95A. PLA/PETG also works. No support needed
Potentiometer knob made for 6mm shafts. The ID on the model is 6.15mm to account for printing error.
Potentiometer knobs with a nice grippy texture. There are four internal sizes to fit most potentiometers : standard 6mm diameter standard 6mm diameter with a deeper hole to cover the fixing nut larger 6.35mm diameter (often used on…
Biomechanical skull creature thing.. will hold headphones. Presliced files included as well as separate files of each part, the model has not yet been printed by myself but I'm confident they will fit together. Assembly is straight…
The usual situation … the maker's solution … Weekend, shops are closed, ordering takes too long …. This time I needed a knob for a potentiometer in a front panel. Compartment for knobs didn't contain any 4mm axis knobs … so let's make it.…
The large sibling of my Potentiometer Knob with knurled surface for Potentiometers with 6mm round axle. The hollow 20mm diameter design covers the nut completely. Prints well on an FDM printer with 0.2mm layer height. Print with shaft…
Case for the Radiomaster Zorro without external module. -Place supports under the latch part of the case! -Hinge: M3x48 screw and M3 Nyloc nut -Latch: instructions->link remixed from roadie3rd https://www.thingiverse.com/thing:2425378
Update 3/5/23: I have added a wider bulb holder for the IOM/US1M style boats. I also added Star 45 boat arms, bulb holder, plates, and clamps. Update 2/4/22: I added a longer pipe catch piece to allow the stand to go into “narrow” mode.…
RadioMaster Pocket Screen Mount This project is proudly sponsored by PCBWay - Your One-Stop Solution for PCB and 3D Printing Services As an FPV enthusiast, I'm excited to share my enhanced version of the RadioMaster Pocket screen mount.…
This is a mount designed for the radiomaster pocket. It has two hooks in the backside. It fits and slides perfectly into the pegboard. The controller is snugly secured into place and easy to get it in and out.
I designed these to work with my home made LM386 portable guitar amplifier. They are designed for a round (with rough edge) potentiometer with a 6mm shaft size. You may need to scale up or down slightly to get a tight fit. This one is…
Joined gimbal covers for the Radiomaster TX16s radio. These are printed in PLA with a color stop part way. Black Hatchbox PLA: https://amzn.to/3sOiSnG Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
I never seem to have the right potentiometer knob for the job on-hand. I could keep a reserve of interesting knobs on hand, but that takes space. Instead, I custom design the knobs, as needed. Here is another of my 3D knob print designs…
My battery lid snapped at the hinge nubs. So I modeled this! It sits slightly below surface of controller for easy printing on a flat surface. To install, put one nub into the controller and bend the lid inwards so that the other nub can…
Triominos Placement game for four people The rules of the game The aim of the game is to score as many points as possible by placing the matching tiles. The points that can be scored during a game are based on the numbers of tiles played…
A clone of the knobs Boss used on their vintage rack units, i.e. the RV-1000. I bought a non-functional RV-1000 to repair and noticed it was missing 3 of the knobs. This is an almost 1:1 replica, the top cap even fits in the same way.…
Perilla de potenciómetro: Nombre del archivo STL: "PerillaPot.stl" Esta perilla de potenciómetro ha sido diseñada para mejorar la precisión y facilidad de uso de tus dispositivos electrónicos. Su diseño ergonómico proporciona un agarre…
My take on a laser goniometer for measuring the edge angles on your knives. It's made to hold a pen style laser pointer with a diameter of 10mm.
I remodeled Cohencos knob to fit potentiometers with a 6mm inner diameter. I really like the rugged skin - it turns out very nice printed at 0.12 layer height.
This model is a Laser Knife Goniometer used to find the precise angle of knife bevels. The knife is held by magnets below the edge and two additional magnets in the tilt mechanism. Tilt mechanism with a knob on the side enables adjusting…
Tiny Arc de Triomphe, reduced to a small, clean object that keeps its main shape and character. Part of the Mini Cars collection — The model is simplified for a reliable print at a very small scale. Print tip: use a 0.2 mm nozzle for…
Small goniometer for medical use. Printed in PETG without supports. Best results with 0,15 layer height. ⚠️ Enable Advanced print settings > Layers and perimeters > Quality > Detect thin walls. The two parts have to be carefully separated…
My late Mom's old Panasonic table radio needed its volume control (with integrated power switch) replaced. The replacement parts would apparently be considered vintage now, but Philmore sells an appropriate value pot with an integrated…
I created this small holder/mount for the Radiomaster RP4TD receiver. It just slides in and stays via friction. If loose just add a dab of hot glue or similar to the edge of the receiver. I print in ASA .4mm nozzle and .2mm layer height.…
This is a phone/screen mount for the Radiomaster Pocket, inspired by a mount on the market at AliExpress at an unspeakable price. It requires: 1x M3x8 (or bigger as far as M5) 1x M3 nut (or bigger as far as M5) (optional) 1x M3 washer (or…
Did not like what I saw on thingiverse. 3D printers don't print very nice in the air, especially when you want ABS, HIPS, ASA, anything other than PLA, so I designed my own, where you can print it out of separate pieces and assemble it…
Protect gimbals and front sticks. New version with upper stick protection! Assembly the two parts with pressure, once in right position the upper part rotates freely. Insert the gimbal protection first, then rotate the other part: on the…
Gimbal Protector for the Radiomaster TX16S I have larger Gimbal Stick-Ends than the stock stick-ends. I wanted a Gimbal Protector that would fit over those but also fit in the Radiomaster TX16S case (the one that comes with the…
I made this for the SP 404 MKii (and that's the only device I tested this with) but I think it should fit most pots. Instructions This model is composed of two parts, “knob” and “indicator” (red and white respectively in the picture…
buymeacoffee.com/dgfpv Push the pin out of the original hinge and swap it with the 3d printed one. Unscrew the sma adapter. The inner counterpart needs to be glued to the inside - from inside of the to the outer bracket. Be very careful…
Oct 25 2025 I adjusted the design to allow for more room to add the threaded inserts, and I added a 3mm hole to make it less messy to add the M2 inserts. Here is the OnShape layout. I have created a variable table so you can really…
Skull knob, 6mm ID for splined potentiometer. 0.20mm layer height, 0.40mm nozzle Brim No Supports In my experience, thermal coefficient of expansion varies between filament types. This is a tight fit that works well for silks. If you…
Pressure fit potentiometer knob for a potentiometer with a 6mm shaft Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: 3d Jake PLA Notes: Depending on the bedadhesion you…
This is a accessory board for the game Minecraft: Builders & Biomes. Four copies can be printed to help align the building and item chest tiles on the table. I also made a Organizer for Minecraft: Builders & Biomes Inspired by Minecraft…
A different take on the compound planetary gearbox. This time, we use split sun gears, synchronize the ring and planet gears. One sun gear will be fixed to the threaded shaft of the potentiometer (or some kind of tuning capacitor), the…
Storage compartment for custom sticks or small things - securely attaches to the extension mod bay of the RM pocket. Update: Added @wengacz_2735054 's double chamfer Remix
this body is made to fit on the custom lcg chassis by N0_Lan ( the betty version) in the files is inlcuded fuel tank for mounting a magnet also there are fender that i made but they are not included in the picture ! happy printing , in…
You can find the enhanced version 2 of this project here : https://www.printables.com/model/1199963-solar-powered-rain-gauge-pluviometer-v2 ------------------------------------------------------------------------ You need : A rod of 3mm…
english (google translate)/spanish I have no idea about motors, but a friend asked me to make this piece for him and he has given me permission to hang it. This is what he told me about her: Goniometer for 2T and 49 cc motorcycles: am6,…
Premium player component insert is available on my Gumroads Store . Organizational insert for the board game Minecraft: Builders & Biomes by Ravensburg. My kids and I really enjoy this game but setup can be a little time consuming. I…
This a Remix of the design of @HandsomePotato The middle part is reinforced
RC sailboat pulley block. Just print 2pcs, they will fit together. depends or your printer tolerances, you might not need even glue. But you can apply a thin CA on holes when fitting. Use 5x8x2,5mm Bearing with both sides sealed (marking…
This is a set of numbers and class insignia that are designed to fit the IOM RC sailboat. They may be suitable for other classes as well. You can re-scale them as you see fit, but be aware that they may no longer fit the IOM…
Printed with the fin
Quick mount mobile holder for the Radiomaster TX16s. Holds a mobile phone or similar (63 - apx. 90mm width) for use with Qgroundcontrol and Ardupilot or similar. Hardware: 1pcs apx. 60mm long 4.5mm (max 5mm) spring in tension. 1pcs…
Just a clamp I designed for two potentiometer I need to put inside a control box. The clamp snaps on Potentiometer so it is not really necessary to put a nut on it for fixing. I used my Top Hat Rail / Cap Rail mount base plate to glue the…