530 models
GEPRC Cinebot 30 GoPro mount with integrated mount for TBS M8.2 GPS module Remixed “Cam mount for GEPRC Cinebot 30 (Gopro 8 9 10 11 12 & DJI Action 2)” form Lenny B FPV The picture shows the part printed with Prusament PETG, 0.15mm, 100%…
Print approx. €1.16–€1.42 excl. taxPreliminary estimate for PETGSource material: PET
Dobrý den, vzhledem ke zničení původního držáku jsem se rozhodl navrhnout nastavitelný držák sprchové hlavice pro využití svého Průši Mini. Model se skládá ze 4 samostatných komponent, které je třeba k sobě spojit jednou maticí…
Print approx. €0.49–€0.60 excl. taxPreliminary estimate for PETGSource material: PET
EN: The removable shower holder is designed for 100mm tap spacing. Must be printed with supports. CZ: Držák sprchy navržený pro rozteč vodovodní baterie 100mm. Nutno tisknout s použitím podpor.
Print approx. €3.74–€4.57 excl. taxPreliminary estimate for PETGSource material: PET
Demo: Attach mirror to your shower pole whenever you need it. Rod diameter 23mm (20-24 would work). Dimensions: 125,5mm x 40mm Instructions: Slider and clip fits together, you can use glue if it is loose, or a little bit of heat if it is…
Print approx. €0.38–€0.46 excl. taxPreliminary estimate for one variant
This STL file provides a replacement wall mount designed to match the original dimensions of the waterproof shower phone holder, model B09PRCJ1W8. Over time, the adhesive backing of the original mount may lose its grip, especially in…
Print approx. €1.40–€1.72 excl. taxPreliminary estimate for one variant
Print & replace orignal Print in PETG or PC Weight in PC is 5.3g tested and works fine Please leave a like if you downloaded it :-)
Modeled from a GEPRC Mark 4 clone. Despite the 5 inch being a freestyle frame, the 7 inch variant is surprisingly light weight and nimble
28mm GPS mount for the GEPRC Mark5 and Mark4 FPV drone frame. The VTX antenna mount is for TBS-style antennas, and the receiver antenna mount is for standard T-antennas. My reason for using a 28mm GPS instead of the usual 18–25mm one is…
Updated(v2): Made some improvements. Printed with TPU. Designed for printing with 0.6mm nozzle, but should also work fine with 0.4mm one.
BN220 GPS mount for GEPRC Mark5 Allows the BN220 GPS module to be mounted on a GEPRC Mark5 with the TBS Crossfire configuration. Besides the BN220, it also houses the VTX antenna and the Immortal Crossfire T antenna. The VTX antenna and…
Parts for my 5 Inch quadrocopter build. The parts are for a clone of the GEPRC Mark4 frame: https://www.banggood.com/custlink/KvvEZ5HHEp Some of the parts should fit to the original frame, too but at least the front bumper won't fit…
Gopro mount on FPV dron. Tested on Gopro 9 black.
This is my first design of mount for BN 880 GPS and two sma connector from DJI air unit. Printed in Flexfill 98A with 0,4 nozzle at 0,2 layer height
Two designing available, choose one, or try both. mk5-arm-guard-slim Light weight, motor installation holes: 16mm - 19mm mk5-arm-guard motor installation holes: 16mm
Cover to protect electronics from dust and wet. I can make designs for other models too. As i can see in this model difference only in arms length (5-10in) 🚨 Looking for a stronger version or have wider frame arms? Check out my updated…
Simple and easy to print arm guard for the GEPRC Mark 4. Protects the ends of the arms where the motors are to prevent the carbon fibre from damage and splitting in crashes. Print in TPU with the flat side on the print bed. No supports…
Cover del frame Mark4 de GEPRC, para protección FPV frente a golpes y material, con entradas de aire y muy aerodinámico, se ajusta perfectamente a la forma del frame, ideal para usar con el soporte gps, también en mi perfil.
I was unable to find a suitable model for an ELRS antenna holder that fits the GepRC Mark5, so I made my own. Additionally, I designed a version that allows for spacers, made of a more robust material like polycarbonate (PLA would…
The part accepts a BN-220 GPS module, a standard vTX pigtail with a flange mount, and standard 3mm antenna tubes (included with the Mark5 frame kit) Prints without support. Can be printed in PETG or TPU, depends on what you prefer. Photos…
This is a design I came up with to solve a problem on my 7 inch Long Range Drone build. I had to stick the high powered VTX on the bottom of the frame, so I needed to lift up the quad in order to give the VTX clearance. I call it the…
Presenting my GepRC Mark5 Arm Guards, designed to closely match the original ones that are included with the Mark5 frame. I noticed that the available online models often had an excess of material on the sides, and consequently, weight.…
Hey there, I have created this model to upgrade my GPRC Mark 4 frame with the new DJI O3 air unit. I have made 2 Version: Version 1 with DJI O3, antenna and GPS mount: The bottom left and right part to hold the DJI O3 Air Unit in place.…
Hi, I've made remix existing Geprc GPS mount and fit it to use with GEPRC Cinebot30. You can use it with two antenas RX and VTX. Best to print from TPU or other flexible filament.
I used canopy model from GrabCad and tinkered simple mount for GPS. I used black PETG till layer 86, paused, changed filament to TPU, reduced temperature and printer the upper part with it. Came out nicely. But it can be fully printed…
This mount is suitable for 19mm cameras with two screws on one side. I created it especially for walksnail cameras that you want to mount on Geprc mark4 I used Prusament red PLA, but you can use some flexible material instead ;) I also…
I recommend using PETG to reduce the amount of vibration or hard TPU filament. you will need insert nuts with a diameter of 3-4mm and a length of 4-5mm for M2 screws. The camera is screwed to the model with 4 M2 screws 4-5mm long. The…
This is basic holder to keep capacitor in place, standoff gap is 20mm, hole dia is 6.2mm. thickness: base plate 2.5mm
I manually measured the arm of the new GepRC Mark5 frame (different from Mark4) and created an arm protection for it. Printed using TPU, no supports, 0.1mm layer height. Fits on pretty snug. Feel free to edit the CAD file, SolidWorks 2020…
Note #1: For naked Gopro9/10 & GoPro Bones. Longer one might introduce vibration during fast-forward flying or any extreme condition if you print at TPU. Since the mount on these is not in the center of the camera structure. So I printed…
A replacement part to add 2 SMA connectors to the Mark5 together with a GEPRC GPS (M8 and M10) Everything is pretty tight but it fits. Print in TPU. A well tuned machine can print it without supports.
A servo-based release/drop/tow mechanism. Mounts to bottom plate of GEPRC Mark4 (https://geprc.com/product/gep-mark4-frame/) Centered weight, middle of frame, directly under the FC Symmetrical mount options, can be attached in both…
Standoff dia: 6.15mm vtx hole dia: 6.5mm height: 24mm
Prop guard for the GEPRC Cinelog 25 version 07 (recommended to use) thicker base wall and arms version 01 first version, bigger diameter (can be somehow tight to mount) Print Settings Printer: Anycubic Vyper Rafts: No Supports: Yes…
PRC-77/25 Baofeng case: This is the best and the most realistic replica of PRC-77 on the internet. Model is 1:1 copy of the legendary radio from the Vietnam war era. Model is primary design for airsoft/milsim events but you can also used…
NEW Version: After crashing and breaking v1, I made a branched version similar to the original design but hopefully more robust. Let me know if it works out better for you! --- The GepRC Cinelog 20 prop guards are very fragile. I made a…
I have recreated an improved version of the Original created by GEPRC for the o3 unit. This version is more aerodynamic, has a much larger and more precise airflow inlet, along with a small lower air passage that improves the cooling of…
Geprc / Phisital mark5 XT60 mount. Holes diameters 3.1 mm, holes spacing 24.5 mm. You can use glue to stick the connector. Printed in PLA.
I created this arm connector for my (china clone) GEPRC Mark4 7 Inch frame, as I found a lot of vibrations on 120Hz getting to my gyro from the 2807 motors. This has removed some noise, but not all of it. Printed in PLA, lasercut carbon…
Update: Got a top side that includes the ability to mount SMA pigtail. For this version you print 2 bottom's to secure the ELRS antenna. Printed with Esun TPU 95A. Printed with a 0.6mm nozzle.
A mount for GEPRC M8 GPS and a regular SMA connector for the Mark5. I believe other GPS like the BN220 will fit but I have not tested it. Everything sit very tight but it works as this model is intended to be printed in TPU. Print with…
Proppeler box for DJI FPV drone Thin and Sturdy Enjoy edit: I have been asked to scale down the box to 70%... added files scaled at 70% as the original model was not designed to be scalled down. Scaled version will acommodate GEPRC smart…
Printed with TPU no Supports (set Bridge Flow Ratio to 0.35)
First version was very lightweight, also easy to install. This version more strong and more crush ready. Also some different design v002 and v003 difference only arms holes, v003 much wider to fits more arms variations. This is an…
Hi everyone, it's been a few years since I bought a Cinelog35 V2 frame and I was trying to redraw it in case I needed to make a new part. The manufacturer didn't have a proper drawing of this frame, so I gave up for the sake of final…
GEPRC MARK5 for 03 CAM MOUNT. Its the same of original model. Left and Right model
I wanted to mount the HLGRC M100-5883 10th-gen GPS module to my GEPRC MK5D frame (Deadcat version). I could not find any mounts that use the stock antenna mounts, allowing for easy ELRS antenna and DJI O3 antenna fitting. Therefore I made…
GepRC Mark5 Arm Guards copied as close as possible to the originals. Holes are arranged to fit a 16mm motor installation size and 8mm motor mount screws. I added a new version with side covers.
Mein erster Versuch einen Walksnail/ELRS Antennen Mount für einen GepRC Mark4 Frame zu konstruieren. My first attempt at constructing a Walksnail/ELRS antenna mount for an GepRC Mark4 frame. Print Settings Printer Brand: Creality Printer:…
Arm protector for GEPRC Mark4 10 inch frame
Custom-fit protective case for the GEPRC Cinelog 30 v3 cinewhoop drone. Designed to store and transport your quad with antennas still attached and a battery mounted—no more bending antennas or removing your battery every time you pack up.…
GEPRC Mark4 Antenna holder VTX, RX, SMA Uses original Hardware
It is an improved version of the GEPRC MARK5. This model is less heavy than the original, more cushioned at the front. It allows to tighten the lower screws and not to create the puffy effect. Tolerances may vary depending on the printer.…
Hey! GEPRC CineLog35 V2 GPS mount. GPS module is used Bainianxing-BU1025TF with UBX-M10050-KB + Flash Memory, supports GPS, Glonass, Galileo, BeiDou at same time. GPS module buy here edit 31.3.2023 v1.2 - added Walksnail and some minor…
Disclaimer: These could be used as a permanent solution, however because there's nothing stopping the duct from clamping onto the prop you will almost certainly be blowing props whenever you bump things. As pictured it was printed in…
Fixed up some of the spacing that caused some of the walls to be printed and not joined correctly. Also reduced the height by about 5mm so that you can fit it onto the quad with the protective sponge parts. Print Settings Printer Brand:…
Even if a GEPRC Mark 4 HD isn't a long range quad, a GPS may come in handy. Either as a fail safe or as a speedmeter. I couldn't find a mount for the front of the quad so I made one from scratch. There are two designs. One for the factory…
Protection de bras pour la frame GEPRC Mark 4, 5 pouces, orienté Freestyle et Bando. Imprimer en TPU, avec support, remplissage 25% gyroïde.
a nice way to mount the XT60 and VTx antenna on to your GepRC MK5 FPV Frame the XT60 is angled to also accept 5.1" props and you might have to solder the XT60 cable at an angle to accommodate a VTx, etc. like me Print upside down
Geprc Mark4 ELRS Reciever Holder
Adjusted dimensions to better find my generic XT60 plugs. Category: R/C Vehicles
19MM BTWEEN the holes . created with ONSHAPE i do not recummend print in plla just tpu .
This model is my design of shower head. Model has a standard ½´´ screw-thread for the hose connection. I printed it from a PETG filament. It is recomended to print it with support and with oblique placement of the model, so that there are…
Model : This model fits the Cinelog25 v2. It is used to mount the DJI o4 Air Unit Pro. It is compatible with ND-Lenses. Print Instructions : Material: TPU, I used the Eryone TPU Filament Placement: Place the model on the bottom, just as…
Hey Pilots, this is a crazy little design. Why this? I Don't know. It adds about 2 grams on the weight and It Is useless but why not? I want to have legs of my Cinelog35 as brand new. Bumpers are suitable for Cinelog35 V1 or Cinelog35 V2!…
GEPRC mark 5 o4 Pro camera mount. Designed like the original. It is thinner, so the camera moves freely. Eliminates the jello effect. Printed in TPU 95A with 10%-20% infill.
Geprc / Phisital mark5 dji o4 Pro antenna mount TPU. Printed in TPU 95A.
I made these two GPS mounts for me and a buddy. We both used the GepRC M10-DQ GPS modules. He has the AOS 7 V5 frame and I have the GepRC Moz7. The Moz7 also needed a rear antenna mount so I added that too. you just need to bend the mount…
geprc mark4 7inch sma+b220 gps mount, print in tpu,
No supports needed. I printed with .08mm layer height on the X1C in PLA-CF and HTPA-CF. I will update with .4mm nozzle and .2mm layer heights in regular PLA. PA12-CF recommended for impact and crash resistance. DM me for improvement ideas.
My first own model created in Onshape. Fits on my GepRC MK4 Frame (Clone). The two screws are covered by the GPS module ! So use removable glue / adhesive pads. The inner dimensions are 20mm x 22mm (W x H). Therefore suitable for various…
Nenašel jsem vyhovující model držáku, a proto jsem si navrhl a vymodeloval svůj podle originálu. Doporučuji tisk z PETG. I couldn't find a suitable holder model, so I designed and modeled mine own after the original piece. I recommend…
I redesigned the antenna mount for easier storage and transportation. 20240902:Upadted Folding Antenna Part 2.
Geprc mark5 o4 Pro antenna mount. Printed in TPU 95A.
Update 19.05.2024.: I upgraded the propeller guards further. Rigid on the inside and flexible on the outside. And 3 grams lighter! https://www.printables.com/model/884159-unbreakable-propeller-guard-for-cinewhoops-upgrade Update…
Geprc Mark5 O3 + GPS MODULE for GOKU GM10 MINI V3 W/COMPASS
The front TPU bumper on the Mark5 often gets excessively compressed to ensure a tight fit against the frame, a practice that's always concerned me. To address this, I've developed a variant of the bumper that includes printable spacers. I…
You have to shorten the antenna by about 5 millimeters black plastic "straw". It's not too hard though, just pull it out and cut it off, you can replace the shrink wrap on the cables for better protection.
Custom-fit protective case for the GEPRC Darkstar 22 micro cinewhoop. Designed to store and transport your quad with antennas still attached and a battery mounted—no more bending antennas or removing your battery every time you pack up.…
A GPS mount for the Speedybee Mario 5 frame and the GEPRC GEP-M10 GPS and the DJI O3 unit. It is best printed with PLA or PETG and you should have plastic glue to glue the two halves together, it should also be printed with support
HGLRC M100-5883 M10 mount GEPRC MARK5 DC TPU
GEPRC CineLog35 GPS mount. GPS module is used Bainianxing-BU1025TF with UBX-M10050-KB + Flash Memory, supports GPS, Glonass, Galileo, BeiDou at same time. GPS module buy here If you would like to support my designs to give me a small tip,…
I made a DJI O3 kit for the GepRc mark 4 HD5, I can't find any good 3D printed that worked for me. I have modded/remixed every part so now its working perfect. No need to buy a longer camera cabel and stuffs. The DJI O3 holder is flipped…
To make the GEPRC RACER compatible with the CADDX vista NEBULA PRO
btween holes is 19mm hole is 6.5
This is a mount for 19mm cameras. Its still not completed NEW UPDATE: Added v2 where camera is moved a little bit forward Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution:…
GPS Mount made for VOLADOR II. It may be compatible with other drones. Printed on TPU 95A 20% infill
Improved replacement for the TNC2188 NiCad accu used with the Tadiran PRC-2200 military radio. Printed with XPETG. Additional Powerpole plugs for charging and powering other devices. Integrated Fuseholder for 5x20mm glass fuses.…
Frame: Mark4 7inch ( https://www.aliexpress.com/item/1005007050126436.html?spm=a2g0o.order_list.order_list_main.33.1d911802EmF5cR ) Not a add Camera system: Walksnail Moonlight 4k kit. GPS: BN-220 Stack: 4in1 ESC + F405 FC Material:…
In FPV (First Person View) drone flying, the application of positioning technology has become increasingly important. Positioning technology not only reduces the likelihood of losing the drone but also provides a stable flying experience…
GEPRC MARK5 DC Dji O4 mount PHISITAL FRAME
These legs are asymmetric to save on weight, and to make them easy to print. They give 60mm of clearance under legs. They're easily retrofitted to any quadcopter but were designed for the GepRC MK 4 quad frame often seen on aliexpress.
General The 25mm version is compatible with 1 inch cable grommets as shown in the picture below as well as M25 cable glands. But you can use the blank plate to remix your own version if you have different needs for your car 😄 The gasket…
Foxeer Mega 5 FPV Drone Antenna and GPS (GEPRC GEP10) holder, if you want GPS on your FPV copter. Printed in TPU with 15 % infill with supports. You can print upright or laying it does not matter. No special settings needed. The GPS can…
TPU GPS mount - HGLRC M80 Pro
7mm PRC stacking loading block. This is a work in progress, so check for updates before printing. Revision History: 05/12/2023 - Text vertical adjusted. Category: Tool Holders & Boxes
A fast remix of Cinelog 30 prop guards, increasing central hole sizes for motor screws. I'm printing with PETG, the durability is nothing to write home about, but it protects the bystanders so there's that.
This O3 Transmission Module Mount keeps all the great design features of the original mount that comes with the GEPRC Mark5 DC. I did fully build this model from the ground up, but largely reflected the general structure of the first…
![GEPRC Mark4 Clone Frame Parts [WIP]](https://media.printables.com/media/prints/98925/images/1000844_bc4bd012-487e-4951-9d7a-7ab5d18e3c8e/featured_preview_quad.jpg)
