1,762 models
Clamp your knife in place, fix the wet stone on the slider and just sharpen your blade. This fixture is ready to go with only 3D printed parts and therefore needs no extra hardware. You might add a couple of M3 bolts later (or similar)…
About the tool A simple whetstone knife sharpening aid. Helps when getting started sharpening blades using a whetstone. 4 Different angles for different types of blades. 14°, 17°, 20°, 25°. Common Sharpening Angles: Pocket Knives- 20°…
Jigs for sharpening Drill Bits up to 10mm with a Dremel and a Cuttingdisk for a grinding Angle of 118° (standard) and 135° drillbits. Credits for the idea to voltNik:-) Update 20.4.2022: I replaced the model-files for those with threads…
Description If the “pen is mightier than the sword”… why not have both for insurance? This simple mod to the classic Fine Point Sharpie adds a new aesthetic sure to please your medieval enthusiasts. This does not replace the existing…
ENGLISH Introducing FlexiScraper : the ultimate solution for effortlessly accessing low-profile prints and stubborn support residue. Engineered with precision, its sharp edge glides seamlessly beneath prints straight from the bed. With…
UPDATE: I created a new, simpler chisel sharpening jig: https://www.printables.com/model/520488-better-chisel-sharpening-jig ORIGINAL POST: My chisel set was pretty dull when I bought them, and they needed sharpening after a couple of…
Better Cleaner overhangs! Teardrop shaped hole with horizontal ring edges. Stronger parts! Weak point at the top eliminated. Rounded edges on contact surfaces! Helps reduce friction between the tool and working surface reducing wear and…
Drill sharpeners in various sizes for DIY enthusiasts - BOSCH PWS 9-125 CE - FLEX orbital sander The drill sharpener uses high-speed rotation for grinding (FLEX orbital sander), it is set at an angle of 118 degrees in total for both…
Remixed Whetstone block, to be used with knife to slide along the block maintaining the correct knife angle. 4 x different angled sliders to get suitable angle. Common Sharpening Angles: Pocket Knives- 20° Hunting Knives- 25° Fillet…
Had to print using 2mm raft to stick on build plate. Print with thicker side of the model upward shown in photo, no supports needed. May require some strands to be cleaned up when done printing. You can find adapters on Amazon but why not…
Knife sharpening helper / guide for 60 x 180 mm whetstones. Remix of "Whetstone sharpening helper" by Rejd (thingiverse.com/thing:2493459). Sliders, slider angles and base plate shape were modified. Max stone height: 30 mm Angle…
Minimalist, timeless bowl in a clear and sharp design. 🚀 Support My Work & Supercharge Your Business & 3D Projects! 🧡 Join my Patreon and unlock 400+ premium 3D models – with new designs every week ! 🔧 Includes STL + Fusion 360 files for…
Support me & Join Printables Club Assembly list of non-printed items for pencil case 2 pcs - metal axis 26( 25 )mm x 3mm 1 pcs - sharpener blade aprox. 6mm x 23mm with screw 2 pcs - M3 12 - 18mm screw If you looking for a bigger version
Stormtrooper Sharpshooter of the First Order. Updated model so its 1 shell and flat bottom. 2.27pm cmt 4/24/2023
Useful tool for getting proper angles during knife sharpening on whetstones.
Prints PETG in 0.2mm layer height with no supports, a 5mm brim around adapter helps with bed adhesion. This is suitable for use with Sharpie fine point pens. Print upright with thin part of the adapter touching the build plate. No…
(Summary consolidated/updated 01/15/23) This is a mini belt sander design intended primarily for sharpening knives though it may also be OK for some light duty grinding/jewelry making/polishing, etc.). It uses commonly available 3/4" x…
Drill Bit Sharpener for Dremel with true Relief Angle. This jig is using a Dremel Cutting Disk for Sharpening. The 2 Parts are held together with a M3 Screw and Nut.
Quick and easy Visor Sharpie/Pen universal clip. Great for field workers who need to scribble quick notes occasionally, and can't get caught without a pen! Printed in Prusament PETG.
I really liked CNCKitchen's sharpener design, but I wanted some extra refinements, making the construction a bit simpler, using not so many different types of screws. So here's my remix. Changes from V2.1: redesigned handle for quick…
A tool for sharpening the tip of a drill bit. The angle of the tip of the bit is 121° degrees. If your angle grinder has
Simple angle guides for knife and tool sharpening. These are not designed to clamp to the knife or hold the angle for you. They are designed to help if you are learning to freehand sharpen. Just rest the knife against the guide, lock the…
Насадка на точило с абразивным кругом для заточки свёрл , угол при вершине 130°. Насадка подойдёт для сверла диаметром до 10 мм, угол 130° может быть использован на свёрлах по дереву и мягкому металлу. Насадка крепится к точилу болтом М6…
I needed an angle guide for sharpening bigger drill bits on my bench grinder. With this I can move the bit on the grinder table from side to side and tilt it around the table edge. For now I have added only 118 degree tip angle files.…
The arm of the Work Sharp has a tendency to deflect or sag as you apply pressure when sharpening a knife. This simple but effective support block prevents that from happening.
This is a chisel sharpening jig. It accommodates chisels as small as 0.25 inch and as wide as 2.25 inch. There are 2 holding positions which I'll call the lower vise and the upper vise. Place the chisel into the vise so that its flat side…
I added text to it so you can remember the use. PLA, 0.15 mm layer height , 10%infill.
This is the fully revised Version 2.1! Watch how to make and use one: https://youtu.be/IM2il-zT2fA Bill of material: Suitable sharpening stones set(aff): https://s.click.aliexpress.com/e/_onjGrqw OR Individual sharpening stones (aff):…
Sometimes sharpies write a little too sharp. This airbrush mod fixes that by makes sharpies able to draw nice noisy airbrushed lines. Simply attach a straw that you can get with a drink at any fast food place and blow through it. The…
I liked this model a lot, but the first print I noticed the scraper edge wasn't as clean and sharp as id like. I found it to be the bottom edge of the model was slightly beveled and as such, the first layer of the scraper was printing…
The Sharp Branches Vase is a captivating fusion of nature-inspired design and modern aesthetics. Its deep matte black finish showcases intricate, sharp branch-like patterns carved into its surface, creating a bold and sophisticated…
This guide is used to get the right chisel and plane projection lengths when using an eclipse style sharpening system. Its pretty similar to the original that it's remixed from except I added a lip to use it on the edge of the bench and I…
I Designed a stylish Tape roll and Sharpie marker holder. It fits perfectly inside a 77mm diameter tape roller and keeps your supplies neat and accessible. The holder has a special compartment to securely hold your Sharpie, making sure…
Support block for the Work Sharp Precision Adjust Knife Sharpener. I noticed that the V-Block Clamp would “sag” when sharpening a knife, thus producing an inconsistent sharpening angle. I designed this support block to eliminate that “sag”.
Sharpening jig using a whetstone. Baseplate has guiding rails, knife just gets inserted either in the 25° slot or laid on the 20° flat of the slider. Not even quite sure what to use the 25° for besides pocket knives that get heavily…
Update 11/22/25: Adjusted blade pocket size of 65 degrees version from 15 to 14 mm, avoid filament not getting cut properly. A long time ago I discovered pomi's filament cutter but wouldn't want to use it without a box a la wapameeto's .…
UPDATE 2024/29/05: Added holder for stone 51,2x19,6 mm. Name is KSJ-06-06. UPDATE 2024/31/03: Added revolving grinding stone holders. KSJ-06-04 is for attaching three stones at once and KSJ-06-05 is for attaching four stones. That means…
Customizable sharpening guids for whetstones / sharpening stones. There are various other versions of such guides available, but none of them made me 100% happy. This one is customizeable in size and keeps the rubber band safe in its…
Attachment for a sharpener with an abrasive wheel for sharpening drills, angle at the top 118°. The attachment is suitable for a drill with a diameter of up to 10 mm, an angle of 118° can be used for most types of drills. The attachment…
Fits a 66mm or less wide common sharpening block. Fixed at 17 degrees for easy operation. Very hard edge knives can take a 15 degree edge, cheaper common ones last longer at 20mm. 17 is a compromise angle used by many for a wider variety…
This model allows you to use Victorinox Dual-Knife Sharpener as you would your Spiderco Sharpmaker. It maintain angle for your sharpening rod at exact 30 or 40 degrees both at narrow and wide sharpener side. Micro variant is even smaller…
Ive designed something to clamp over the existing guard on a bosch 115mm angle grinder then clamp your angle grinder to a bench to sharpen 12mm, 10mm, 8mm, 6mm, 5mm, 4mm drill bits 2x 90mm 8mm bolts & nuts required. mine are my usual CF…
Pencil holder in the shape of a giant sharpener. No supports required.
The tool is a remix of the fantastic original model, which is super easy to print and works great. It has been redesigned to fit Parkside (Lidl brand) AC Multi-Tool "Dremel" tool and adds additional features. For small drill bits push the…
Also see my Diamond Stone version of this rolling sharpener. Most home knife sharpeners have you drag the blade across a sharp edge or small diameter grinding surface. While this works well initially, after repeated use, it'll start to…
A simple assistant to keep a constant angle while sharpening knifes with a whetstone. Technical Data: for Whetstone 180x60x30 for Whetstone 182x62x30 for Whetstone 200x50x25 Print Settings: no supports required printed with normal PLA…
Combines the benefits of free-hand sharpening and a fixed-angle system. It takes less space than a full fixed-angle system, allows you to use any stone, and is quicker to use. Just put a knife on a magnet, set the angle with a screw, and…
Features: - suportless magnet holes - easy to get the pen or sharpie from tray - stackable design
Use Case : Printed at 101% scale to avoid any threading issues with my Dremels. Printed all four versions of the sharpener and was able to thread onto my Dremels without any clean-up or post-processing. Accessories : Dremel Lite 7760 -…
Rolling Knife Sharpener with inbuilt planetary gearbox with Mechanical Advantage of 1:3 (HORL compatible) Important: This part is published under the Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0) licence!…
I wanted a dispenser for my insulin needles that could hold a lot of them. The 110mm tall one should hold an entire box of 100 comfortably but there are smaller versions included if you prefer. The inside has a small slope to help them…
Cricut Pen holder for Sharpie. Extra fine has been tested, Fine is still under development. It should be adaptable for most pens. Check out the spreadsheet in the Freecad source. Print .2mm layer height, no supports. Flip it so that the…
I recommend scaling up to 1" on the sides (166%).
When designing a 3D object, it is good practice to first model the object you are designing around. The most recent Prusa Flash Contest is focused on Sharpie Mods , and I have seen many entries that only rely on a simple radius to…
Takes up one hexagon on the Storage Wall, requiring one of the standard M3 inserts available in that project. Stores a standard 12mm diameter Sharpie pen, and just needs a small push to clip the pen in, giving a satisfying little click.…
With this slip-on tool you can easily sharpen you drills. it will slip-on the protector (1mm with) of your angle grinder. I printed it with PLA but i think it is better to print it with ABS. Use brim and full supports only on the bed…
Tossing used blades in the trash is really bad. Tossing them in this box, and then in the trash is much less bad. NOTE: The razor blade silhouette on top is a separate solid body within the mesh of the box, you can select it in the…
Hier stelle ich euch mein Design Messerschleifgerät vor! Ich wollte einen Messerschleifer mit Rotationsfunktion designen, welcher gut funktioniert und dazu noch gut aussieht. Ich denke, dass ist mir gut gelungen. Die Montageanleitung ist…
Mount a sharpie inside a drawer that will automatically present itself for quick access. Simple lever mechanism will lift and lower the sharpie when the drawer opens and closes. Easy one-handed operation! Update 2022-08-27 New version of…
25/04/2024: V2 Version - added cutouts to the sides so sharpies and pens with pocket clips should also fit 4 of the holders now. Thank you @XanderShade01_404080 for the idea. Here is a link to his remixed version.…
This is an original pantograph design made to hold a traditional sharpie. The design allows the user to either double or divide the tracing in half by switching the location of the sharpie. It also includes a holder for a 40x40mm stencil.…
Copycat of HORL sharpening system, easy to print, no supports. Printed in PLA, infill at your choice, in my case all has 15% gyroid, 3 perimeters. Orings best in TPU hardness 95A, really good fit and no mess to install. Parts are oriented…
A replacement lid that fits a Sharpie, made in the form of an historically accurate medieval mace, being modelled on one of the maces in the Royal Armouries Collection of Leeds, England. It prints fine, vertically positioned, without…
This a remix of Machvolum's model which comes from visle's original model. This version add's rounded corners to Machvolum's model. The theory is that on sharp angles (such as 90 degree corners or similar) the extruded filament tends to…
This is a little 50mm (dia) x 60mm tall can for disposal of old/used hobby and utility/box-knife blades. It's sturdy, strong (even when printed in PLA), and printing it should be relatively quick and inexpensive. I had a growing pile of…
Description: This is a remixed version of the original drill bit sharpener, redesigned to fit a 115mm diameter grinder. It offers a compact and efficient solution for sharpening your drill bits with ease. Printing Configuration: Material:…
I wanted to made my own sharpening guide getting inspiration form the ones available on the market, several designs I found on internet and the one I built some years ago with pieces of wood and furniture rolls that wasn't so accurate I…
Wiper blades stop wiping well when the edges of the rubber blade get rounded off and are not as sharp as new. This can be remedied by cutting a thin strip of the blade off and generating a new sharp edge. Use this tool and the sharpest…
Description Drill Bit Sharpening Attachment for Angle Grinders – a simple and practical tool for sharpening metal drill bits using an angle grinder. This drill bit sharpener is designed to work with many popular angle grinders. Simply…
The Sharpie Fine markers will fit in the Cricut Joy, but the rim is different from the original markers. With this adapter you can use your Sharpie on the Joy without problems. Incl. Fusion360 file
Holds sharpies, which is a bit fatter than most pens. It can even hold a set of tweezers. Connects to the multiboard system using either a snap or pushfit. There is also now a 15mm version to hold larger items, e.g. toothbrushes. See more…
Although I was not too successful with the original design I made this holder which I found more convenient. Works with 5mm x 5mm x 5mm cubic magnets like these: Example No Glue was required for me. Tips for assembling: Use a flat object…
Messerschärfer Folgende Teile werden benötig Tischplatte. Multiplex 15mm Abstand 1 und 2 Multiplex 15mm. Oder kann auch gedruckt werden. Führungsblock 1x 8mm Welle. 180mm lang 2x M8 Muttern 2x Feder 10x2x70 2x LM8UU Messerspanner 2x M8x60…
A remix sharpie holder with just one sharpie for multiboard
Knife sharpening guides for whetstone sharpening. These guides will help you learn what holding a knife at 45 degrees to the stone at an angle of 20 or 15 degrees feels like. These guides will help you develop the muscle memory for…
I made a replica of a single sided razorblade. They are a quick print and work well for separating very thin or stuck parts from the print bed. Because they are so thin the is less of a ramming prying acting when separating parts! The…
A modification of MikkoP's Sharpie Storage Block that allows four standard black sharpies to be stored tip down as well.
This is a add on for a basic Work Sharp sharpening system, with this add on you can use any sharpening stone from 3 1/8 inches long all the way up to 6 inch long stones. When printing these components it's important to print the Lead…
Normally after you catch a fish, you hold it up by the lower lip while you remove the hook and pose for pictures of your big catch. When you're out fishing for predatory fish, like big ocean fish, you need to wear gloves or use a tool…
Update (9/16/24): added .f3d file so that you can customize the angle as desired in Fusion 360. You will need to install the Parametric Text add-in if you want the angle text to update automatically. Fully printable guide for your…
A simple stand for markers of all kind
Sharpener Heyho I have developed a candle sharpener for a local school to make it easier to place home-made candles in holders! But the sharpener also works for conventionally bought candles! Scalability: The sharpener is of course super…
Most home knife sharpeners have you drag the blade across a sharp edge or small diameter grinding surface. While this works well initially, after repeated use, it'll start to form divots on the edge -- kind of like washboarding on a dirt…
Remix of knife sharpener with additional features.
This is a guide that screws on to the front of a standard rotary tool for sharpening tungstens (TIG welding electrodes). To use this, you will need a rotary tool, 25mm diamond sharpening wheels, and four 1/4-20 x 1/2" brass set screws,…
ARTICULATED SHARPIE GUY As requested, here is my articulated version of the Sharpie Guy. I designed this based off the 3.5" G.I. Joe's from my childhood. I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions…
This is the version 2.0 of my riser for the Work Sharp Ken Onion Blade Grinder, u/timinator6 and I have developed the version 2.0, now with a slider to get the blade closer to the belt maintaining the 0 angle! Also, the Slider finishes on…
I bought a 9-piece set of sharpening stones for Stefan's CNC Kitchen knife sharpener ( https://www.printables.com/model/81237-knife-sharpening-tool-v21-with-video ), but needed a way to store them. There are cases for smaller sets but not…
a JIG inspired from the already not available JIG SV 45 from Tormek, as they replaced it by the new KJ-45 JIG, proposing a better centering of the knife and as a consequence a symetric angle of sharpening for both sides. However, offering…
A shallow tray for Sharpie Pens. Two depths. Deep on better for stacking. The shallow one site nice as a top tray - I needed it to fit an extra layer in the draws I'm using.
It may not be a replacement for true colored filaments, but now you can add any sharpie color you want to your filaments. I've tested a few filaments and found that matte white and clear filaments do the best at taking the color. Pictures…
Compact Sharpie organiser that keeps markers upright, secure, and easy to access. Space-efficient grid layout with a stable base for everyday use. I've given them a slight forward lean and a staggered the height of the rows for easy…
This is Deadpool's head with holes sized for sharpies but other pens or pencils will fit fine, Was printed on anycubic mega pro, can do 5 to 10% infill, I used 0.20 layer height.
A clip for a sharpie to attach to your hardhat. One warning it the clip is a tight fit and difficult to get off after its attached
Use case Helps to hold a certain angle while sharpening (kitchen) knives on a stone. The jig matches sharpening stones that are 70mm wide. I designed it with the Shapton KUROMAKU series in mind. Variations Model comes in two variations:…
Custom made for my Wusthof whetstone (ref 704773), here is my sharpening device ! Inspired by some i found here, i made my own, according to my tastes and needs. I purchased the stone online on knivesandtools (24€ + shipping) , very happy…
Multiboard Holder for your Pen, Knife, Sharpie or Pencil. This prints perfectly without any type of support. I designed this to be right in the sweet spot so it can be used for multiple items. The opening is 11mm wide. The unit is 45mm…
SharpGuide: Carpenter Pencil Sharpener Guide This unique 3D-printed carpenter pencil sharpener guide is designed to offer a precise and efficient sharpening experience for two popular pencil sizes—7x10mm and 7x15mm. The guide features…
The tool is a remix of the original model with where it has been redesigned to fit Parkside (Lidl brand) dremel tool.
sharp arrow head with hooks material used: PCTG infill: 100%
