122 models
Printer: MK4s Layer Height: 0.25mm Nozzle: 0.4mm Materials used: PETG / PLA Supports needed: No Infill: 15% Print times: Total: 5h29m / 55m white / 4h34m black Need help? Find me on Discord: https://discord.gg/NndzwJvN
This is a holder for Steelseries headphones Chatmix dial. The mounting point will print solid and will need to be drilled out by the printer to fit the appropriate mounting hardware you'll be using. Can be mounted to any solid surface,…
My Steelseries Apex keyboard recently lost one of its rear feet during a move, and Steelseries support doesn't sell or provide replacements. This is a model for a replacement foot that roughly matches the stock foot – it's not an exact…
A cheap and easy fix for cracked and broken Arctis headphones, You will need, Retaining Clip plyers or E clip plyers Loctite Super glue MUST BE THIS TYPE! A soldering iron A screwdriver A 11mm or 7/16" drill bit OR Dremel and patience……
if its doesn't fit try making it smaller. :)
I need to travel with my headset sometimes and decided to create a case for it! Can hold both the headset and the DAC along with any cables you may need as well. DAC fits in the middle of the headset band (see image) inside the case. Fits…
This is a small tray that gets screwed into the underside of a table or a shelf, next to the edge, for conveniently mounting the SteelSeries GameDAC. All ports remain accessible. Designed for screw mounting, but Command/Power strips might…
Enables you to mount your Steelseries Arctis Nova Pro DAC to your Aluminium profile simrig. The mount also has a place to store your spare battery.
Intro: This is a travel case I have designed for traveling. It's fits the Nova 7, and I assume the 7X and 7P. There's a smaller compartment to fit the wireless receiver and a small charging cable. Print settings: I printed this all in PLA…
I printed these with PLA+ with a 4mm nozzle and 0.2mm layer height. I used the default Cura profile for PLA. I advise using raft for adhesion as it will help with the support material removal. You'll also need magnets from amazon, I used…
It is recommended to print on a high-resolution 3D printer and not FDM since the distance is very small
A lightweight shell for Steelseries sensei 310. After buying a new mouse, my old one was left collecting dust. Heavily inspired by Optimun Tech's Zeromouse ( https://www.youtube.com/@optimumtech/ , https://zeromouse.co/ ), I modelled this…
This is a remix from https://www.thingiverse.com/thing:398515 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: Devil Design PLA Green
The stand is a single piece printed on the back vertical face with no supports required. It is my own design using FreeCAD 0.19 specifically to fit over the Siberia 840 OLED Transmitter unit. The transmitter case seems to be the same size…
This is a remix for fitting my base I printed the Original part in DevilDesign Black PLA, and I wasn't able to fit the deck in the support without snapping in 2, so i made this remix to fix the problem Steelseries Artics Pro Deck
Hello! I designed in Fusion 360 to help get my DAC mounted underneath my desk.
My Steelseries Aerox 3 WL has been sliding around on the original stand so I created a bit less universal mouse pillar. I started from the ground-up again based on the measurings of the original STL.
Holder for Arctis Nova Pro Wireless and the Base Station Category: 3D Printing
I recreated the headphone cup caps (they may be called “Speaker Plates” for my SteelSeries Arctis Pro Wireless. It maybe be possible to FDM print these with a 0.4 mm nozzle, but I have not attempted it yet. I just wanted to try and…
Printed 0.15mm Filament: 3DJAKE magicPLA
Mouse Holder(Case) - Steelseries - Rival 3 Very simple with Steelseries logo for desk. Internal Dimension: 67.5 x 42 x 63h mm Also check the radius of the curvature if it is suitable for your mouse, the model it can be rescaled. Add Model…
Updated 11/14/24 Should load into slicer as intended to print, minimal or no supports. Thanks for the help with development and testing to user @Arson_2595054
Steelseries headbands are notoriously bad. Comfy, but wear out easy. This clip for the Arctis Nova Pro is made to hold the headband securely in place. Printable in PLA.
Simple holder for SteelSeries Arctis 1 Wireless headphones, would work with other headphones of the same brand with same cable extender for dongle. Jednoduchý držák pro sluchátka SteelSeries Arctis 1 Wireless, bude fungovat i pro jiná…
I designed this speaker mount for my SimLab P1-X Pro using the SteelSeries Arena 7. Should work with Arena 3, 7 & 9. Should also work with extrusion profiles for various sim racing frames. Mounts using single M6 socket head bolt. SimLab…
Design does not have screw holes. I glued it to wall and it holds up nicely. It is a bit long to wall to prevent headphone rubbing against wall. Design has step file so you can modify it your needs. No supports needed
Hi there, i designed an adapter for all Arctis ear pads for the new SteelSeries Arctis Nova Pro Wireless headset. assembly Instructions: You need to remove the ear pads (there is a video on youtube on how to remove it) check if the…
Steelseries Arctis Pro Cyberpunk plate Just need magnets once printed You can use multiple colors using mmu/coolor change as height are different for each colors. Though I would recommend resing printing and painting
This holder will let you place once for all the transmitter under your desk. It have not being designed to be removal. It's ugly but work's well. You can place it with 3M tape under a glass table or any desk. The battery tray is still…
Print instructions Print in PLA The multi-color effect can be easily achieved even on single-color printers. Just print the logo first, change the filament, and print the cover “on top” of the logo. To avoid collisions, the logo and cover…
Presenting a take on Tom Nardi's (HSW) creation, catered specifically for those seeking a Steelseries Logo Version. Behold!, three distinct Width versions, measuring 35 mm, 45 mm, and 55 mm, each offering both extruding and intruding…
Battery case for your SteelSeries Arctis Nova Pro headset. I only used prusament PLA for this, 15% infill, brim, no supports. Pretty much default settings. Most filament materials should work.
Inspiration from this .
Update: Added a MEDIUM size which should sit tighter than the large but not give you a headache. After using my Arctis Nova 5 for barely over a year the outer frame snapped when I was taking it off normally. Quite disappointing. Since the…
A small mounting bracket for the Steelseries Apex Pro keyboard to hold a USB Type-C female breakout board, allowing for the replacement of the USB Type-A pass-through port to be used as either a pass-through USB Type-C or to create a…
This is a tiny small print for key lock replacement Print into Super Quality mode Remove all previous lock support from key and glue with CA in place. Be carefull on centering key and switch.
Bought a steelseries arctis pro wireless headsett wich comes with a bluetooth hub that needed some upgrades. Print x1 Hub Print x2 Feet Glue the feets on the bottom of the hub. Feets are taken from kafka who made a remix from Subsite
This is a clip to retain a smartphone to a game controller for playing games. Because the XBox and Playstation game controllers are more popular, the SteelSeries Stratus XL seems to be overlooked. So, I made this smartphone mount for my…
This is a mouse holder designed in SteelSeries style but can be used for non-SteelSeries mice with an additional option without the logo.
SteelSeries Arctis Nova Pro Wireless DAC Stand| Sat on table too low for me, so with zero experience i made that abomination. Tips are welcome
Bracket and horns for the Steelseries Siberia v2 headphones Remixed From: Little Horns by Scottland Print instructions I printed the bracket on edge with supports, but didn't require any for the horns.
Steelseries hub (61298TX) holder i printed with PETG and it took around 4 hours. (tight fit) I choose PETG for durability to put hub in this holder Used 0.2mm line height with supports. But maybe you can print without ;)
SteelSeries Stratus Duo Stand
This is stand for SteelSeries mouses. Compatible with other gaming mouses.
The idea was to create some cosplay like attachments for the Steelseries Arctis Nova 7 to bring some laughter to a web meeting. As there were only two models - sdahris Arctis Nova Ear Plates and the original SteelSeries Arctis Nova 7…
couldnt select the right license. correct one is: i dont care what youll do with this.
Additional M2x6mm screws are needed. Simply unscrew all four existing screws and place the adaptor on top of the plastic cover. M2 screws should just fit in without any problems. Do not use extensive force! Afterwards, any SteelSeries…
Wall hanger for SteelSeries Arctis Pro Wireless headphones. Takes on 4mm woodscrew into either wallplug or stud. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: eSun PETG…
Prints fine with 10% infill. Only needs support on the top part. Screws in at the bottom with two screws.
This is a phone mount for the SteelSeries Nimbus MFi controller for iOS. I had a commercial one I bought for an XBOX One controller that worked pretty well, but it wore out after awhile of taking it on and off and blocked the switches on…
Steelseries Arctis Nova Pro Battery Holder x2 - x3 - x4 Holds your batteries nice and snug, ready to be deployed in seconds when your active battery dies… And it looks better on your desk than letting the batteries float on your desk or…
I designed this model to hold a couple of spare battery packs for my steelseries Arctis Pro Wireless headset. It fits over the top of the base station so your spare battery packs are always handy. It should fit snugly and not require any…
I had enough with the dangling headband, the headband stretches over time and every once a while i tighten the headband, which leaves a dangling strap. Please if there is any suggestions post them in comments, also if you would like to…
Clip to hold the USB dongle for the Steelseries Arctis 1 Wireless. It attaches the dongle to the headband when not in use, and still allows you to plug it in to a USB port without needing to take off the clip. Just print it with the flat…
I wanted more room on my desktop so i made this holder to mount it under the table. Space to use all the ports
This adapter will allow you to mount the microphone horizontally on the original vertical stand that comes wtih the microphone (print with 0.15 layer height) (the last 4 images is V2) (credit to agepbiz for the screw design for V1) -and…
A quick and reliable solution was needed to secure the device to the edge of the table. I didn't want to mess up the case with tape or some type of tie, so I came up with the idea of making a case that could be secured with both glue and…
Clip for STEELSERIES Stratus Duo, for One+7T. It's not available to buy it in Europe so inspired by https://www.thingiverse.com/thing:1498137 and created my own clip for my OnePlus 7T. Created in fusion360 - file available here to modify…
Both model's are rescaled to fit better on the headphone. The one with the Punisher Skull you can color change it if you like. You can use multiple colors buy using different height for each layer height. I'm using prusa mk3s with a 0.6mm…
Also works with Steelseries Nimbus
I really like the SteelSeries Wireless Pro but it`s a bit stupid, that the headstrap is not adjustable. So in order to release pressure from my ears I created these simple adjustments that clip perfectly onto the headset hanger in order…
The main body parts have been combined into a single part, which emits the need for screws.
This headphone stand model is designed specifically for the SteelSeries Arctis Nova Pro Omni Wireless base station. It features a sleek, integrated design that securely holds your headset while keeping the base station easily accessible…
i made this so i could put my receiver for my headset somewhere more convenient and out of the way. originally i wanted to have it clip into something but couldn't find a good place or mounting method. feel free to remix this to mount…
A custom 3D-printed mount designed to install the SteelSeries Nova Pro DAC under an MSI monitor. Maybe is only MSI monitor (i have G241)
I wanted to mount my Steelseries Aerox 3 Wireless 2.4ghz dongle on my monitor. It's 105% oversized to account for error, the dongle fits flush but don't expect a friction fit. v4 was the print displayed on the pictures. The USB-C…
A shell following the original contours but scaled up to avoid cramping I would experience
USB dongle holder for SteelSeries Arctis 7P (PS5) so you can mount it to the PS5's panels for a better signal reception and a cleaner look of your gaming area. Two versions available : - Minimalist for a classic look (print with 0.4mm…
Command strip headset holder. This can be mounted anywhere on a vertical surface. This hook is longer to accommodate the broader headband of the SteelSeries headphones.
I made these because I put weight on my £120 MX500 and broke off the feet pins. They're shaped similarly and fold in just like the originals, 100% infill and the pins are stronger than the originals (in my experience). Width is 24.70mm,…
Hello, i own a Steelseries Arctis Pro Wireless. After about 5 years i discovered a small crack on the right side near the bracket where the rubber band is inserted. I tried to glue it with special plastic glue, but unfortunately this…
This a replacement headband for SteelSeries Arctis 7/7+/9X/ArctisPro Printed out of TPU you never need another one. You can adjust the length if you need more space. The original headbands get lose after some month, so I made this to not…
This cable spool was made specifically to fit the ChatMix dial on top of the spool while allowing the cable attached to the dial wind up inside the spool. The top of the spool involves a fitted snapping function for assembly that is made…
SteelSeries Apex 9 TKL Dust Cover
These are earcup accent plates for the arctis nova pro series of headphones. It should fit any arctis nova pro submodel. You can print them in any color you want to make your headphones more yours. The right and left sides are the same,…
This remix fixes the following issues: Fragile locking tab: The original tab was too thin and prone to breaking; it has been reinforced. Internal height: The original clearance was insufficient and crushed the ear pads. This version…
The arctic 7 receiver/transmitter has always been annoying because it is small and light. The tension from the cable makes it turn around and be in the way on the desk. When I saw the mount for it I printed it hoping that it would solve…
Bracket for broken SteelSeries Arctis Pro connection
I really liked the original cat ear design—it’s simple, stylish, and easy to print. To make it compatible with my SteelSeries headset (Arctis 7+), I remixed only the clip portion. The original ears can still be used without any changes.…
I may be sitting in unhealthy and weird ways, but essentially I managed to regularly press the mic mute button as well as change the volume of my headset through the back portion of my chair and in winter my sweaters were enough to reach…
I was inspired by a reddit thread in which someone made a charging station for their headphones with a magnetic charging cable you can find off of Amazon. The original user didn't share their model, so I've made one myself. It's…
It is basically a underdesk keyboard mount for Apex Pro Mini Wireless . As seen on pictures, you may use it on any perforated surface. I have used M3 bolts and nuts to tighten it. Printed with PLA with %15 infill and no supports needed .…
Wall holder mount for Steelseries stratus+
AlzaErgo Arm D35B holder for SteelSeries Arctis Nova 7 USB dongle
Printed with PETG 0.12 mm layer height. Inner/Outer/Inner wall print order. Ironing all top surfaces, 20%. 2 wall loops. 15% infill.
I found myself occasionally forgetting which way to switch the mouse on at a glance, as the bluetooth and 2.4ghz labels are hard to read. So rather than use a paint pen, I've spent over 270 waking hours and 42.7KG of filament designing…
Microphone in Sony Pulse 3D headset is very, very, very, very bad. People told my that over and over in multiplayer games. So decided to change things: microphone taken from cheap (bought broken from second hand) SteelSeries Omen by HP…
Printed 0.2mm, 3 walls, 15% infill. I did organic supports, support enforcers only and then painted on supports for the floating ring. I printing in black ASA but any filament should work. Fitting the phone mount onto the controller clip…
A lid to print with the original model base, removes a box shaped face on the inside of the lid. Also positions the logo object for easier printing, either change colour by object for AMS/CFS, or print the whole object as one colour.
Having detachable mic in your headset might be tiring - it bothers when it's lying unnecessary on the desk and when you need it the most, always can't find it. Here comes the mic holder for Steelseries headset! Very easy and quick model…
This is a wireless charging stand for the SteelSeries Arctis Nova Pro enabling the headphones to charge using a built in Qi charger. It requires you to add a Qi-to-USB-C adapter to the USB port on the headphones and to either remove the…
How to assemble and modify your mouse: You'll need: 4x 5x2mm neodymium magnets and superglue Print the extension with the top surface on the plate. don't use auto-orient Glue 2 of the magnets into the holes in the switch extension you…
I had an apex 7 tkl I wanted to use on my sim, and modified this mount to hold it very securely. The keyboard is held solely by friction, and is quite tight. The riser requires M3 heatset inserts, and is fastened using m3x8mm BHCS with…
Disclamer: Not printet jet. Just s simple remix to add some suport + zipties. Alsow, made the "cable channel" a littel wider to be able to hold all cables(usb/power) and provide some cable managment. Possible modifications as soon as I…
I hate it when I go around with my laptop during meetings and always have to ensure that the wireless dongle does not hang around and stresses the USB port. This ugly gadget was my first design in tinkercad. It looks like sh** but works…
I've removed the hinge in favour of a cylindrical pot to glue the top-end of a generic self-stick that can be bought from any cheap shop (i sourced mine from Daiso). This is the style of the one I purchased
This is an under the table, Steelseries Arctic pro wireless hub holder, to make your desk space nicer. Tips are much appreciated. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill:…
I need a riser cradle so my DAC sat above my keyboard. I remixed another model and created 4 variants. Remixed from PolyGone's (PolyGone_124826) fantastic Sim DAC Mount. Comes in 4 variants: 1. Flat without logo 2. Flat with logo 3.…
Introducing the SteelSeries Battery Holder, the essential accessory for your SteelSeries headphones that use swappable batteries. Designed for convenience and efficiency, this sleek battery holder ensures that you always have a fully…
