Search results: tablesaw

Sort order

49 models

P
Printablescrashkg

Replacement Bumpers for Ridgid Tablesaw Fence

The Original Ridgid TS3650 Tablesaw is great except for one issue. The fence. It never stays square to the blade. This is because the little bumpers under the fence have very little surface area to clamp to the rail. I increased the size…

Downloads
53
Likes
12
Rating
0
P
PrintablesPeter H

TABLESAW THIN RIP JIG

Despite the way it looks, this is a very simply tool to print, although some care is needed to insert nuts and a bearing during the process. The following is a step by step set of directions for printing, assembly and use. I shouldn't…

Downloads
1,104
Likes
669
Rating
4.91
P
PrintablesJiltedGeek

DeWalt DWE7492-QS and DWE7491-RS tablesaw insert

Because I broke my tablesaw insert plate, I needed to design this replacement part. I made it as accurate as possible and in two parts so it fits on the build plate. It is not a ‘zero clearance’ version, but as the pictures show a…

Downloads
856
Likes
158
Rating
4.67
P
PrintablesMerto_Bohan

Featherboard for Parkside tablesaw

I was looking for this part but found nothing compatible with my Parkside tablesaw guide rails (ref PTK 2000 E3), so I quickly designed one. It should be compatible with other models with same guide rails. You will need two M5x40 screw…

Downloads
570
Likes
116
Rating
5
P
PrintablesWyldesyde007

Craftsman tablesaw zero clearance throat plate

A zero clearance throat plate for an old portable craftsman table saw. print the pieces as they are laid out. The plug end for the hook is deliberately tight to get a snug fit after a small amount of sanding. Print instructions Print…

Downloads
509
Likes
78
Rating
5
P
Printablesblerghcity

Dewalt dwe7485 Tablesaw dust port adapter for 1.5" hose vacuum (ShopVac)

The popular Dewalt dwe7485 tablesaw has a 2.5" dust port (2.3" ID) that was WAY too big for the 1.5" OD hose I had standard on my ShopVac. Hardware stores didn't have the correct reducing couplers so I designed my own. There is an…

Downloads
393
Likes
47
Rating
5
P
Printablesnpopson

Thin Rip Jig for Tablesaw

Table saws are dangerous. Print and use at your own risk. Designed to require very little additional hardware. The tolerances between sliding interfaces is about 0.2 mm. You may have issues with binding if your printer is not dialed in,…

Downloads
349
Likes
75
Rating
5
P
PrintablesBrice A.

DEWALT 7485 Tablesaw Tube Clip

This design is made for the DEWALT DWE 7485 TABLESAW This clip allows you to hold and remove the tablesaw when it's needed. No need to unscrew it, just grab it and move. To get a stronger print, I recommend you to print it with the " U "…

Downloads
321
Likes
98
Rating
5
P
PrintablesRubenRybnik

Tablesaw Pushstick

Table saw pushstick, quickly drawn to fit my Prusa MK3 print bed. Original design found here Print instructions Category: Hand Tools Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: .6mm Nozzle, .4mm…

Downloads
293
Likes
46
Rating
5

5/8 Tablesaw Miter Slot Slider

5/8 Tablesaw Miter Slot Slider, to build custom sleds or jigs; Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot , but this is for a non-standard saw. This slider is 5/8” x 1/4” with a 1/8” “T” slot. Each has 3 holes, countersunk…

Downloads
253
Likes
28
Rating
5
P
PrintablesLeon.Reijnders

Tablesaw Jig for Small Stripes (OnShape)

With this Jig you can cut small stripes on your tablesaw . additional needed to assembly: 1x Ballbearing 608 1x M6x20mm Screw 1x Washer M6 2x M5x30 Screw 1x M3x8 Grub screw 2x Heatinserts M5 The models are made for the tablesaw Bosch…

Downloads
153
Likes
49
Rating
0
P
PrintablesThe Mikester

Tablesaw / Shopvac Adapter

A hose adapter so that I could hook up my DeWalt table saw to the Stanley shopvac

Downloads
138
Likes
18
Rating
5
P
PrintablesSnobound

Tablesaw Dial Gauge holder for Delta table saw

This tablesaw dial gauge holder is made to fit directly in the slot machined into the table of my Delta saw. The gauge is used to measure the distance from the slot and the blade at front and back to insure the blade is aligned correctly.…

Downloads
133
Likes
28
Rating
0
P
Printablespoprhythm

Featherboard Miter Bar for older Tablesaw

Allows usage of this featherboard to be used on a table saw with ¾" miter slot (with 3/8" depth). Uses three 1/4-20 UNC hex bolts, 2 ½", and nuts. This style of miter slot is a straight channel - no T shape to tighten vertically. The…

Downloads
132
Likes
23
Rating
5
P
PrintablesLaisch

Tablesaw Accessories Tray - Hammer K3/B3

Tray for the Wrench and the Allen keys for the sawblade change on your Hammer K3/B3. Mounts under the sliding table. To fix it in place, simple use double sided tape.

Downloads
122
Likes
17
Rating
5
P
PrintablesTD3D

Metabo Tablesaw Blade Guard, dust hood V2

I would recommend acrylic glass for the sidepanels but if you have a big printer you could also print it. The holes have M4 threads. Hose with 32 or 35mm outer diameter required. Designed for the Metabo ts254m, but should also work for…

Downloads
109
Likes
12
Rating
0
P
Printablesdlbrando

Alignment Tool For Delta Tablesaws

This tool is meant to be clamped to your table saw while you align the front and rear rails for the fence. It is derived from the measurements shared across multiple woodworking forums where this tool is wanted, but not available from…

Downloads
79
Likes
4
Rating
0
P
PrintablesJMSDesign

Bladeguard for Tablesaw sled

I print at 0.6 nozzle 0.3 layerheight 0.6 layerwidth 4 perimiters 4 bottom/toplayers 20% infill No supports. Thanks

Downloads
65
Likes
22
Rating
0

Rigid tablesaw to Vacuum Adapter

This is to attach a tablesaw vacuum output 2.5" (64mm) to a 1.75" (44.8ishmm) vacuum hose. I have both a Rigid Tablesaw and Vacuum I used ABS. .2mm layer 100% infill No supports

Downloads
64
Likes
9
Rating
0
P
PrintablesChris

Craftsman 315 Tablesaw Miter Runner

This is just a quickie table saw runner for a crosscut sled I'm building. I made the fusion file with parameters so that it can be customized. It will print nicely 260mm long at 45° on an Ender3 S1. The holes take #6 screws. Notes for my…

Downloads
63
Likes
9
Rating
0
P
PrintablesAndrew Rousseau

DeWalt portable tablesaw clips

This is a set of clips to hold down a DeWalt DWE7480 10" portable tablesaw. It's a compact saw but that means it is prone to shifting when ripping long material. I found it a pain to use the screw holes to secure it to my mismatched stand…

Downloads
62
Likes
34
Rating
0

Parametric tableSaw guide

Should fit guide rails for other tools as well. Can be edited using the two variables: NumberOfHoles and DistanceBetweenHoles Also I've added a fitTollerance variable to adjust ti fitment of the guide inside the rail to compensate for…

Downloads
60
Likes
10
Rating
0
P
PrintablesSwimfar

Tablesaw Featherboard - Prusa Mini-sized

I liked design8studio's open featherboard model, but it was just a little too big for the Prusa Mini build plate. So I trimmed the back off of it while keeping the fingers the same. I also reduced the thickness of it in a few areas to try…

Downloads
58
Likes
15
Rating
5
P
PrintablestokoD

nutenstein ulmia 1710 / t-nut ulmia 1710 tablesaw

Ein Nutenstein für die Ulmia 1710S Er kann eine M6 Schraube aufnehmen. Dient bei mir zur Befestigung eines Abweisers (für Kleinteile). Category: Machine Tools

Downloads
56
Likes
3
Rating
0
P
Printableskukulin

slider for tablesaw jigs Stanley STST1825

as my table saw has non standard tracks i made this simple slider to use with crosscut sled and other table saw jigs. It has counterbores for flat head screws. Holes are 3.8mm diameter for screw and 7mm for head.

Downloads
44
Likes
7
Rating
0
P
PrintablesAMacG

Runner for Bosch Tablesaw (for Blade Alignment Jig)

This is a remix of the runner part of the excellent "Table Saw Blade Alignemnt Jig". The original runner has a rectangular profile which does not mach the T profile of the Bosch tablesaws. I made a quick remix which fits quite nicely. To…

Downloads
44
Likes
3
Rating
0
P
Printablespowerfulgryphon

thin rip jig for tablesaw ryobi remix by npopson

remixed carrier part to fit Ryobi T-track(miter slot) table saw. remixed part requires supports so make sure supports(use supports everywhere option) for whatever slicer you are using are dialed in to avoid supports fusing to the narrow…

Downloads
37
Likes
4
Rating
0
P
PrintablesPC

Tablesaw Delta T3 Fence Top T-Slot T-Track Rail

I needed T-Track/Slot Rail for my Little Proteus Powerfeeder by Al Ladd Woodworking to fit nicely on my Delta T3 fence . The T-track sizing was taken from the Powertec 71568 32" Miter T-Track with Miter T-Bar . The Powertec T-Track is…

Downloads
36
Likes
7
Rating
0
P
Printablesthelanlegend

Tablesaw Crosscut Sled Blade Guard

A blade guard is important to prevent accidents when using a crosscut sled but they make the sled itself clunky and awkward to store. The blade guard attaches to the fence using the same T-Track you might already be using for your stop…

Downloads
35
Likes
12
Rating
0
P
Printablesriethmueller

Runner for Festo Basis plus for the awesome tablesaw jig of Peter H.

This is a redesign for the runner of the awesome table saw jig of Peter H. I printed this to use the tool for the raw cut of Kumiko stripes. The runner is re-designed for a Festo Basis plus. Like the original you have to embedded a nut…

Downloads
33
Likes
2
Rating
0
P
PrintablesRifer

Tablesaw with DC Motor

Its a 3d Modell of a almost complete 3d printable Tablesaw. The only Hardware Parts You Need are: Switch, 9-12V DC, DC Motor The Motor I used, is not completely round. On the Top and on the Bottom it is flat and left and right is Round.…

Downloads
24
Likes
3
Rating
0
P
Printablescrashkg

Tablesaw Arbor Wrench

This is the flat wrench that came with the tablesaw for a 5/8th's arbor

Downloads
24
Likes
3
Rating
0
P
PrintablesDano

Tablesaw STOP Paddle

The oversize STOP safety paddle broke on my Craftsman tablesaw so I made a new one. ***I corrected the spelling for this upload.***

Downloads
23
Likes
8
Rating
0
P
Printableskentthoresen

Bosh tablesaw tsp100 100mm vacum connection

Dust connection for a 100mm hose in stead of the tiny 35mm thing that comes withj the saw Category: Parts

Downloads
21
Likes
2
Rating
0

Adapter for Bosch tablesaw and vacuum

Adapts the vacum system to a Bosch tablesaw. Fits 63 to 92 mm.

Downloads
20
Likes
4
Rating
0

Craftsman Tablesaw Vacuum Adapter

Vacuum adapter for craftsman tablesaw to a craftsman garage vacuum. Simple stepdown, wedge fit.

Downloads
18
Likes
3
Rating
0
P
PrintablesFroth Beast

Handle for my tablesaw miter

Handle for my tablesaw miter

Downloads
18
Likes
1
Rating
0
P
PrintablesGavin McNair

Original short T slot for Titan tablesaw

A shorter T slot for the Titan tablesaw. I used it for a featheredge adapter like this one https://www.printables.com/model/330457-featherboard-for-bosch-gts-10-xc-table-saw

Downloads
18
Likes
1
Rating
0
P
PrintablesDeerUncle

Height and tilt adjusting knob for tablesaw Sheppah HS-105

More damage resistant version of the knob. Original cap fits well. Recommend print at 50% infill

Downloads
17
Likes
6
Rating
0
P
PrintablesA.Gostick

Altendorf Tablesaw Knob

This is my first practical model from scratch, so I have no printing recommendations. I printed it at 0.15 It is designed to take the thread insert from the old knob and have it glued in. I have not busted the old thread insert out yet so…

Downloads
16
Likes
1
Rating
0
P
PrintablesGerryPB

Small Tablesaw Fence

This is a fence I designed for my small tablesaw. The photo shows it clamped in place but I later made the proper knob using a threaded rod. If there is interest I can post more details , photos, and instructions.

Downloads
14
Likes
1
Rating
0
P
PrintablesStyria3D_prints

Tablesaw_switch

This is a switch for old Tablesaws. Mine broke and i modeled this instead of buying the whole electronics on amazon. Print this like in picture 2 with supports and 100% infill

Downloads
13
Likes
4
Rating
0

Ozito Tablesaw Tool holder

Tool holder for the two spanners to go with the $120 Ozito Tablesaw sold at Bunnings. It already had holders built in for everything else but for some reason not these! Just attach it to the plastic blade cover using M4 nuts and bolts.

Downloads
11
Likes
3
Rating
0
P
PrintablesJeff

Zero Plate Atlas Tablesaw

I wanted a Zero Plate for my Atlas Tablesaw so I made this, put on saw, then slowly raised blade to make cut.

Downloads
9
Likes
0
Rating
0
P
PrintablesAndrew Rousseau

Boch TS-1000 tablesaw stand foot

This is a replacement foot for the Boch TS-1000 table saw stand. The legs are steel square tubing with in ID of 28mm. This fits snugly inside the tubing just as did the original. There is a one piece foot as was the original and a two…

Downloads
9
Likes
0
Rating
0
P
PrintablesAndiSz

Minitischkreissäge Schiebetisch, Minitablesaw

Dieser Schiebetisch wurde speziell für die Minitischkreissäge von Amazon entwickelt und dient vor allem der Sicherheit beim Arbeiten. Der Parallelanschlag ist so konzipiert, dass er mit einer eingelegten 3-mm-Mutter, einer passenden…

Downloads
7
Likes
0
Rating
0
P
PrintablesZIO designs

Havey Tablesaw arbor wrench holder

I got sick of always looking for my Harvey Tablesaw Arbor wrench every time I needed a blade change. This magnetic holder can be stuck anywhere on the saw base so you always know where it is. I printed with PETG, .20mm, 6 walls and 20%…

Downloads
1
Likes
4
Rating
0
P
PrintablesRex

WoodPeckers StealthStop + DropZone tablesaw miter sled wall hanger - Locking Retainer

This wall hanger stores a WoodPeckers StealthStop table saw sled, with or without the DropZone. The lower ledge supports the sled while a spring loaded retainer locks it in place. Pull and rotate the retainer to remove or reinstall the…

Downloads
1
Likes
1
Rating
0
P
PrintablesZIO designs

Harvey tablesaw 3mm Allen wrench throatplate magnetic retainer

This is a Magnetic retainer to hold a 3mm T-handle Allen wrench that fits the throatplate retainer screw on a Harvey tablesaw. I printed with PETG, ,20mm, 6 walls, 20% infill and tree supports. Attaches with AT-N52 D10x3mm Neodymium…

Downloads
0
Likes
1
Rating
0