77 models
Simple adaptor plate to use the rear of the BMW navigation cradle with the fitting bracket for a Garmin, TomTom or other standard four-screw mount
Remote control case. Two versions, one with buttons. The other version only has holes. The case is designed to prevent accidental button presses in your pocket. perimeters: 4 layers: 0.2 I look forward to seeing photos of your prints. :-)
Mobile and connectors: Printing: PLA is sufficient, as this is all light weight. 0.2mm layer height, 3 perimeters. I recommend printing the ball caps with 2mm brim and supports on the ledge of the 45degree connector and underneath the…
This is a Holder for the NetAlly NXT 2000 Spectrum Analyser that sits on a MAC M2 Laptop screen. Designed so you don't break the USB connector when using the NXT2000 with Mac Version of WiFi Explorer Pro. Will print without supports. .2mm…
This is a Holder for the NetAlly NXT 2000 Spectrum Analyser that sits on a PC Laptop screen. Designed so you don't break the USB connector when using the NXT2000 with WiFi Explorer Pro. (this one is for a thicker screen) Will print…
Originally published here: Motorola Moto G72 G82 & Edge (2022) xt2205 case by tato_713 - Thingiverse Some of the models are designed for rigid materials and others for flexible ones. The models materials are not interchangeable , so pay…
This is for your XT2. You can use it as a bumper or add the sun screen for extra utility. Print it black or crazy colors to customize your bike. If you print it please upload a picture and share your creation thanks! If you like this,…
Originally published here: Motorola Moto G60 & G60s xt2133 case by tato_713 - Thingiverse Some of the models are designed for rigid materials and others for flexible ones. The models' materials are not interchangeable , so pay attention…
Blink xt2 mount with original drill holes
Originally published here: (WIP) Motorola Moto E20 xt2155 case by tato_713 - Thingiverse This was designed for the Motorola E20, but it may be compatible with the E40 as well. Some of the models are designed for rigid materials and others…
Originally published here: Motorola Edge 20 xt2143 case by tato_713 - Thingiverse This case is for the regular Edge 20 model, for the Edge 20 Lite/Fusion see this . Thanks to KonstiSFX who helped me testing this case. Some of the models…
Originally published here: (WIP) Motorola Moto E7 & E7i Power xt2052 case by tato_713 - Thingiverse This case was designed for the phone E7, E7 Power and E7i Power. It could be compatible too with the E7 Plus, but this one has a slightly…
Originally published here: (WIP) Motorola Moto G9 Plus xt2087 case by tato_713 - Thingiverse Some of the models are designed for rigid materials and others for flexible ones. The models materials are not interchangeable , so pay attention…
Originally published here: (WIP) Motorola Moto G20 xt2128 case by tato_713 - Thingiverse This is a work in progress, the case could not fit on your phone. . For different reasons, I have trouble to test some of the phone cases I have…
Originally published here: Motorola Edge 20 Pro / S Pro xt2153 case by tato_713 - Thingiverse This case is for the Motorola Edge 20 Pro , for the regular Egde 20 see this case ; and for the Edge 20 Lite see this case . Thanks to Marcus…
Fits standard 28.6mm motorcycle handlebars and is secured with double sided mounting tape and zip ties. The tape prevents rotation and adds some vibration dampening. Uses 4 M3x16 bolts. You should be able to use any standard key to…
A two-part mount to fit a Garmin XT or XT2 to the handlebars. Requires M4 set screws and nuts (I recommend Nyloc nuts) to complete, which are readily available.
Mount to attach garmin xt2 to a mt450 via the stock dash bolts. I used m4x25 to mount the garmin charger. PETG 0.2 35% 10 walls 5 top and bottom
Originally published here: Motorola Moto G51 xt2171 case by tato_713 - Thingiverse Thanks to Angel Alonso who helped me testing this case. Some of the models are designed for rigid materials and others for flexible ones. The models…
Model of the Garmin Zumo XT2 with attachment plate. Not perfect model* but outer dimensions and mount surface is accurate. Made for base for other designs, feel free to use it to your liking. I have designed holders and will come up with…
Print with PEG, 100% infill
Needed to mount my Garmin Zumo XT2 on a BMW 1250 GSA and wanted to use the original bracket. This might also work for the Zumo XT, if the charger is more or less the same as XT2 ( but i have not tried it ). I wanted to mount it without…
My dad needed a way to mount a Blink camera without making any holes or modifications to the exterior of his condo. So I whipped up this little mount that clamps to the 2" post of a light in his front yard. When assembled there should be…
Originally published here: (WIP) Motorola Edge 20 Lite xt2139 case by tato_713 - Thingiverse This is a work in progress, the case could not fit on your phone. This case was designed for the Samsung S20+, including the 4G and 5G versions,…
Originally published here: Motorola Edge xt2063 case by tato_713 - Thingiverse These cases were designed only for rigid materials, because the wide range curved borders prevent to make a good attach for the phone, and it will probably fit…
These are mini Marathon motor covers for the ⅓ scale XT22 by Nascarsimracing1, Its also compatible with the legacy 3T22, and other siren models that utilize the same mounting pattern. Feel free to save the image of the tag and glue it on…
I received a couple of enquiries to adapt my original Blink Indoor Camera Window Mount for the XT2 series of Blink cameras. The design of the XT and XT2 case is quite different from the subsequent Blink Outdoor cameras, in that there are…
Garmin Zumo XT2 / XT mount cover with Alarm sign and text. It protects the electrical contacts and functions as a reminder or warning that the alarm system is active. Printing Instructions: 0.4 nozzle 0.20mm structural 15% infill no…
Description: A custom-designed waveguide for matching the depth of the Visaton W170s' origin of sound with the Vifa/Peerless/Tymphany XT25G30-04 ring radiator. The diameter of the WG matches the woofer's. The waveguide should also fit on…
Deets The chain slider on our beat up old XT225 finally gave up the ghost. Ive been wanting to fix it, but it gets ridden a lot. Thankfully the old one broke off so the swing arm didnt need pulled. This model omits the angle for the…
Based on the Blink XT2 Power Bracket by Walchek (great design by the way). Instead of hanging the sync module off a wall socket I just designed two side brackets to mount to a wall or cupboard using screws or a piece of sticky backed…
Duratrax Evader EXT2 Spur Gear Cover Print it upside down with the threaded hole touching the buildplate, with supports. Print instructions Category: R/C Vehicles
What it is: A compact Arca compatible tripod plate designed around Peak Designs Anchor mount for fujifilm XT2 and XT3 cameras. The Peak Design Anchor mount allows you to mount your camera strap or wrist mount to the bottom without…
Wall holder for FAAC XT2 FDS RC. Easy to print. Both PLA and PETG worked. Printed on 0.16 layer height but choose what you like.
no a la venta Adaptador para BMW R1200 R1250GS se agradece que dejen un comentario con fotos y se añada a me gusta.
size : 3X2 u total height : 90mm
made a visor clip for your car for the new faac fds xt2 and xt4 remote controls print with a brim, i had to use supports with petg. pla worked without. two files - one regular clip, one larger stronger clip. more flex with petg.
A simple mount for the Ankermake Wireless Cameras to hold on the left side of the Z axis at the Ankermake M5
Sottile cornice per riparare l'occhiello rotto del radiocomando stampato in TPU è il TOP, se stampato in PLA è un po' strettino ma cosi non si sfila. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution:…
This is a replacement for the battery strap and ESC mount of the Evader EXT2. The ESC mount will work with all Evader chassis, including the ST, ST Pro, EXT, etc but the strap will only work on an EXT2 or any other Evader that is already…
Simple stand for your navigator. Made for just storing or perhaps display (not possible to connect USB cable). If you like my work, consider buying me a coffee: https://ko-fi.com/maildannesholkse Check out other Garmin prints in the…
Blink XT2 side mount for bookshelf The model allows to install a Blink XT2 camera on a bookshelf and look in a direction parallel to the bookshelf, helpful in example if the camera monitors an hallway. The model is composed by 4 elements…
Table stand with adjustable angle. Can be used on table or if you put some rubber on it you can use it on car dashboard as well, and then you can use an angled cable. See pic below. Three different parts to print: Additional hardware…
Based on the Blink XT2 Power Bracket by Walchek (great design by the way). Instead of hanging the sync module off a wall socket I just needed a bracket to mount to a wall or cupboard using screws or a piece of sticky backed velcro (you…
This model is a dedicated screen protector for the 6-inch Garmin Zumo XT2. It is a redesign of the original Zumo XT cover to fit the dimensions of the newer generation hardware. Function: Protects the glass during storage, transport, or…
This is a recreation of the mount that comes with the Midland MXT275 GMRS Radio. It features wider slots in the base to accommodate more mounting options, such as the Rugged Radios Toyota Seat Post Mount . The mount reuses the quick…
On each side of the cot, a dummy plug is present that can be raised to reveal a mount. This mount is designed to attach the holder. The hole designed for the pipe is slightly larger than 12mm, so you may need to wrap some tape around the…
Here is the XXL-version of the diffuser for the Klarus XT21X flashligt. :-) Handy when you need to turn all that concentrated lightbeam to the surroundings. Perfect on the kitchentable during that poweroutage, in the garage or on that…
cover suitable for the remote FAAC models XT2/XT4 433/868. Very useful to protect your remote and easy to put/remove from it! It has to be printed with TPU or any other softer filaments. Leave a like if you like it thx!
This is a flashlightstand for the Klarus XT21X model if you ever need. It is a litle hard to get the flashlight to stand up right when needed. It is used in combination with the Klarus diffuser that you can find here. The Footstand is…
Here is the diffuser for the Klarus XT21X flashligt. Handy when you need to turna all that concentrated lightbeam to the surroundings. Perfect on the kitchentable during that poweroutage together with the Klarus Fottstand that you can…
These are mini Marathon motor covers for the ⅓ scale XT22 by Nascarsimracing1, Its also compatible with the legacy 3T22, and other siren models that utilize the same mounting pattern. Feel free to save the image of the tag and glue it on…
Xt22 pole holder Hardware: 7x Self tapping M4 screws (any length)( you might want a longer screw for the Bigger mount) This is so the legs dont get bent when mounting it also to hold an Xt22 with small legs You may notice the wedge is…
Here's my first 3D model. It's holder for Mi Temperature and Humidity Monitor 2, to place it in Chicco Next2Me Dream and monitor temperature around newborn/children. I use Tree Support to print it. Used Nozzle 0.4 and PLA.
About See what it looks like here: https://www.youtube.com/shorts/_z8Omeqew1A NOTE: YOU NEED TO BE COMFORTABLE WITH WIRING AND MODIFYING YOUR ELECTRICAL SYSTEM FOR THIS MOD. I AM NOT RESPONSIBLE IF IT GOES WRONG FOR YOU OR YOU RUIN YOUR…
Regal für 3 USB Festplatten .
I own a set of Blink XT2 security cameras. They come with a small cone-shaped mount, and if you want to power the camera via a cable, the cable will get squished against the surface you mount the camera from. These mounts offset the…
This is a spec sized dummy of the Garmin zumo XT2 GPS for motorcycles. The specs of the overall block and screen size are represented as presented on the Garmin website. This model was made just to have an idea of how much space the…
I merged the ball from plasticlamp into the next2me holder so that you can attach plasticlamp parts into the next2me, in my case to hold a phone that acts as a baby cam. I recommend tree support for the sliding rail. Added some clothes…
Print 22 horns: ten for the bottom, 12 for the top. The top intake hat is of course for the top but with a more accurate looking support.
For when you don't want to carry your Zumo XT2 but still want the option to use your phone as GPS without having another mount on your handlebars. Made for the X-Grip with part number: RAP-274-1-UN7U Prints in two parts, assembled using…
Motorola Moto G Stylus 5G 2022 XT2215 (Volume Button Replacement) (MUST. BE. RESIN. PRINTED.) Feel free to use this for literally anything, I do not care, as long as you follow the rules of my license. (I hate corporations go away, shoo).…
MEANT FOR @nascarsimraci_903773 's XT22 MODEL! This was made to solve a problem I had with my own print, where the shaft would slide in the rotor's “slot” (basically not moving the rotor at all). You might have to modify it, though (my…
It's 2 pieces to attach and glue with a 3rd connecting piece. Printed with: PLA, 5 wall layers, gyroid 20% infill. Mounting: place on the side, at the top edge first and then tie with 2 zip ties to the lower metal bar.
This 3D model is designed to connect buttons to my motorcycle's handlebars and to house the FAAC XT2 remote control in a compact enclosure. The enclosure provides space for the controller’s mainboard and two batteries that power it. The…
porte filtre pour moto Yamaha XT250 de 1986 imprimer en Nylon pour resister a l'essence et huile
This is a remix of the Zumo XT holder. This holder is suitable for the Zumo XT2. For installation, the original holder from BMW is still used. Needed is twice the spacer and once the adapter. For mounting may require slightly longer…
this will come afteri print the model so bnasically dont print this
This is the rear turnlight for Yamaha tw200 (225) and xt200 (225) bikes. I don’t actually know if this useful for other yahame bikes, so try. When installing, don’t forget to connect light bulb fist, so you don’t need to disassemble it…
This is a Holder for the NetAlly NXT 2000 Spectrum Analyser that sits on a MAC M2 Laptop screen. Designed so you don't break the USB connector when using the NXT2000 with Mac Version of WiFi Explorer Pro. Will print without supports. .2mm…
These are mini Valley motor covers for the ⅓ scale XT22 by Nascarsimracing1. Feel free to save the image of the tag and glue it on the inside of the junction box cover I printed these with 20% infill and about 80mm/s Nozzle temp of 255…
This is a recreation of the mount that comes with the Midland MXT275 GMRS Radio. It features wider slots in the base to accommodate more mounting options, such as the Rugged Radios Toyota Seat Post Mount . The mount reuses the quick…
Print 22 horns: ten for the bottom, 12 for the top. The top intake hat is of course for the top but with a more accurate looking support.
What it is: A compact Arca compatible tripod plate designed around Peak Designs Anchor mount for fujifilm XT2 and XT3 cameras. The Peak Design Anchor mount allows you to mount your camera strap or wrist mount to the bottom without…
Use same printing settings as for the rotors on the XT22 page. Use 99% infill, no supports, PETG, PLA+, or PLA.
