256 models
Printed in black PETG with 0.2mm layer height, 4 walls and 30% infill. I would recommend using PETG as a minimum, for layer height you could go to 0.24. 4 self tapping screws are required per side. Update 10/11/24: Added modified cup…
Window lifter button for Opel Astra H 2000-2006 Printed in pla it didn't last long, I had it printed in resin from a friend and it has been working for 2 years
Original document holder must be modified. Use double side tape (or glue) and 4 screw for each side. Print twice (one mirrored) It is for 7 inch 1din radio. Might be used for 2 din (I didn't try it)
Everything you need to fit modern hardware into a mac pro 2006 case. Print in a suitable material with a glass transition temp of 80C+ (i used abs and asa) Refer to this video for details - TBA
I modeled this with dimensions taken from the official part. I have not used it for my install as I also modeled a custom version to exact fit my Kia Niro / JBL speakers. Update 3/14/23: I printed a piece to compare and my measurements…
Tweeter Pod for Scanspeak D3004/602006 & other scanspeak Automotive tweeter (D3004 series) this pod angle 25 degree. Need brass screw insert : M3 x 4 x 4.
central locking buttons, both lock and unlock button. Inserting buttons require disassembly and insertion inside the battery case. On top of the board
EDIT: Slightly improved model, made handle smoother. Do not use PLA, it will melt in the heat! Best to print out of PETG for heat resistance and layer adhesion. It can be printed in any orientation, but not without support. Would…
This model I created to mount the wideband in my GMC Sierra 2006.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Includes STLs for both left and right. They screw into the parcel shelf and mine have worked as intended since 2022. Print in PETG preferably to put up with the car getting hot.
I created this part because my cup holder separator failed on my 2003 Camry, mainly because of a small piece of plastic breaking out of the mounting hole that the tabs for the separator slip into. This part has longer pivot tabs than the…
Lexus GX470 Backup Camera Mount This model is a simple 3D printable mount for attaching an aftermarket backup camera to the OEM mounting location on a 2006 GX 470 SUV. The mount was designed for use with this " NATIKA Backup Camera IP69K…
This funnel allows for easier refilling of the engine oil of a 2006 Toyota Prius. It fits into the opening in the engine block snugly and wedges in between other parts of the engine to make sure it does not move around when you pour in…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
2006 Ford Fiesta Keychain, to be either cut in slicer to print it flat or printed with supports. (I did not make the car model, I just found it and remixed it) Thank you for downloading my design. Remember to like the model if you…
Scraper Bar Replacement for Greenworks Part R0200650-00 for 22" Snow Blowers, Tested working great with my SN60L02 but according to Greenworks should work with the following as well: Product Number Voltage Model 2605902 80V SNB403 2610102…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Als Ersatz für eine kaputte Sterndichtung bei einer Bestway Flowclear 2006l/h. Eventuell auch bei anderen passend. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 90 Filament: any TPU…
Tweeter Pod for Scanspeak D3004/602006 & other scanspeak Automotive tweeter (D3004 series eg. D3004/602006) this pod angle 25 degree. Need brass screw insert : M3 x 4 x 4 for tweeter mount and M3 x 3x 4.2 for pod to mount bottom base Need…
Cover for Pressure steering for Air Suspension Fiat Ducato 250
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Just another Honda Civic (2006) Gen8 keyholder... Three models inside: Basic Basic with hole Special wheels and hole You need to enable thin walls parameter to printing the stuffs inside the wheel :) Pick your favourite… :) Happy printing!
Vintage Video Games - Yakuza - Kiryu Kazuma - 2006 3D printable model.
This is a spare part for a Plissee system used 2001-2006. Those parts are no longer available (at reasonable prices) so I decided to model this "Spannschuh" myself. I used Autodesk Fusion 360 for this purpose and tried to replicate the…
This was designed quite a while ago for a 1st generation Toyota Auris 3door hatchback. Adapter for the back might also fit the 5door hatchback version... i would assume so. Because this is automotive use i would reccomend atleast PETG…
This is a bigger headlight dust cap for a BMW R1200GS 2004 model (confirmed but it should fit newer models as well) for LED conversion. Due to a heatsink or a mini-fan usually found on these types of bulbs, the original cap (part number…
Space Transport Vehicles - Soviet Soyuz TMA-7 - 2006 3D printable model.
My center console latch broke, so I 3D modeled this replacement for it to save $9. It is a drop-in replacement for the original part. I simplified the organic curves on the OEM part to make modeling easier, but it still fits and functions…
Solidworks 2017 Part Category: Replacement Parts
Brackets for additional switches Ford Transit ’06 (2006–2013) For single and double switches. Pictures show brackets compared to dummy plug.
Carcasa para llave Ford Focus 2006, se imprimen dos partes iguales.
I printed them using ninja flex TPU on a purse mk3 S+ with a .4 nozzle, .2 layer height, 245 nozzle temp, 4 layer wall thickness, 40% grid infill on a texture steel print bed. with bed supports. with these settings I feel it came out…
идеально подходит
Passenger Seat
If you own a GTO (and why else would you be searching for this) you know how fragile that dash panel can be. I found out the hard way… twice. I have had this car for 20 years now, and I've taken that panel off a could time in that time,…
Broke the rear seat release knob on my 2006 Scion XA and modeled up a quick replacement for it.
I've designed a Trunk curtain retainer for KIA CEED SW (2006-2013) The original numbers are: for left 859371H600, for right 859381H600 This 3D Model was printed with ASA and ABS filaments. This is my third design in Printables, so please…
Front Speaker Adapter designed for my 2014 Subaru XV Crosstrek for Kicker DSC650 speakers. This replaces Metra 82-8901, so as long as you know your speaker hole spacing should be easy to adapt for other speakers. This should fit most…
I had no place to put trash in my truck and so a bag would just be drifting arounds. With this frame, I can put a plastic grocery bag in and easily throw things away. The arms mount to the lowest bin in the center dash. The lid assembly…
I designed it for my son, it's fully printable in various colors. Give it a like if you liked it, just knowing that makes me happy. I also added two holes of approximately 11mm by 2mm on the base so you can attach a neodymium magnets.…
Cat People - Oliver Yates (John Heard) & Alice Perrin (Annette O'Toole) - 2006 - 2006 3D printable model.
I didn't like the look of the rubber cover that came with the MOMO hub, so I designed a smooth version. Printed with a 0.2mm layer height, I modelledthe bottom of the part 0,2mm thick to have good bed adhesion. This part needs to get cut…
Sci Fi Movies - Idiocracy - 2006 3D printable model.
Renault Megane Sedan 2006 keychain
Scaled & screwed in, Printed in PETG With PLA+ - 100% Infill made it sturdy With PETG - 15%-30% Infill was fine Printed on Ankermake M5C
Deadwood - Trixie - 2004-2006 3D printable model.
Deadwood - Seth Bullock - 2004-2006 3D printable model.
iPhone 12 / 13 / 14 / 15 / 16 Pro Audi TT Mk2 (2006-2014), Audi Q3 8U, CD Concert Support Changelog: V2 - Added power button and volume button, respect the orientation of the phone, and extended compatibility to Audi Q3 8U (2010-2018)
Design is at the end of video
EDIT: Hey, this has been remixed, and the remix is better ! (Thanks D Rogers!) -Iggy. Just a cap that I whipped up for the above mentioned vehicle. I am 90% certain the oil change guy flipped the cap up, the retaining thingy snapped, and…
This is a replacement screw cap for the windscreen cowl of a Mk. 6 Ford Transit van. I was going to be charged £16 for 4 and decided to model it myself. Each one takes less than a gram of filament and there are both flat and clip…
Silent Hill - Grey Child - 2006 3D printable model.
Deadwood - Wild Bill Hickok - 2004-2006 3D printable model.
Deadwood - Calamity Jane - 2004-2006 3D printable model.
Deadwood - Sol Star - 2004-2006 3D printable model.
NOTICE: This has been tested with a 8th gen Honda Accord. Only vehicles using a similar keyfob will work. A replacement enclosure for Honda key fobs that requires no screws and has built-in, custom supports for easy assembly and printing.…
Very rudimentary spacer to raise the 3rd brake light up 1" to clear my 33" spare. How I Designed This Removed the 3rd brake light and measured rough estimates. Could be optimized, but it works. Category: Automotive
Deadwood - Cy Tolliver - 2004-2006 3D printable model.
300 - Xerxes - 2006 3D printable model.
Fog lamp cover for Citroen 1.4. I made it by scanning from the original part. I'm not sure about compatibility. you can support me with corrections.
Deadwood - Alma Garrett - 2004-2006 3D printable model.
Stay Alive - Countess Elizabeth Bathory (Maria Kalinina) - 2006 3D printable model.
Finally, a hardpoint for you to fit your mobile phone into your van or motorhome! You can print it mirrored for either side, maybe fit both! Now you can finally mount your phone in an unobtrusive place using adhesive pads, screws,…
Sick of using a lighter socket charger and wanting to use that for a cheap TPMS monitor, I wanted to replace the blanking plates used in better models for heated seat switches. Rather than cutting holes in the existing panel, which in…
A velocity stack made for the ITB of a 2006 Kawasaki ZX6-R 636. For car use. The throat is 55mm with a slite sitting part on the bottom.
Deadwood - Doc Cochran - 2004-2006 3D printable model.
An insert for female USB leads to go into one of the empty control spaces in a 2006 Subaru Impreza WRX. The gap in the middle should be enough for two female leads to fit snugly. This was created to set up a tidier way of containing the…
If your battery tray is a chevy and its a single bolt design it should fit. I would suggest full infill and a high temp filament such as ABS
Deadwood - Dan Dority - 2004-2006 3D printable model.
Update I no longer use this mount. Instead, I have my AMPS pattern cell-phone mount that accepts any of a universe of standard off-the-shelf AMPS-pattern phone mounts. This is the base for a cell mount for a 2006 Infiniti G35 Coupe. It…
Hello! I've made this simple double cupholder design for Opel Corsa C 2006. whole point is that original cupholder is not deep enough and every drink i put in it falls over and spills, so i made this cupholder design with walls high…
Center cap replacement for 2006–2011 Honda Civic alloy wheels
Deadwood - E.B. Farnum - 2004-2006 3D printable model.
An insert for the cup holder in a 2002-2006 Toyota Camry (most models, I think) that facilitates securely holding smaller cups or bottles. The original part seems to wear out and fails to stay in place. They are difficult to find in the…
Ersatzteil Sonnenblenden-Scharnier für den Sprinter W906 von 2006-2018.
Stay Alive - October Bantum (Sophia Bush) - 2006 3D printable model.
This is a drop-in replacement cap for the 2nd Generation Honda CR-V
I designed an oval base to fit a 2006-2007 Subaru Legacy Outback Oval emblem (link below). I used the base to zip tie it to my 2012 Forester Sport Grill. Worked absolutely perfect, and looks great (factory, even). Not sure if it will work…
compatible parts for metal screw kit merkur M3.5 screws
Copied from original parts. Be sure to print in ABS….. ask me how I know!
Car air cond vent broke, need connector, designed it, printed it with PETG, you're good to go. STEP files included if you want to mod it. No commercial selling of this pls. only for personal use.
Pajero Gen3 Gen4? MK3 2000-2006 speaker spacer and cup protector thingy It was designed for Axton 16.5cm speakers. I thinned it a bit, and added the splash shield like the OEM part has and then some holes for wires and water weeps This…
My WRX was missing one of these, and the other was all worn out. Replacing these fixed my gear lever flop. Not a high temp environment nor a critical safety piece, so safe to print and use. Tolerances are tight with my flashforge finder,…
Stay Alive - Abigail (Samaire Armstrong) - 2006 3D printable model.
PETG with 15% infill
This is a model of my great grandparents home in Bethlehem, PA. Designed in tinkercad
Reworked Kawasaki velocity stack. Improved air delivery with better tumpets
https://www.printables.com/model/1335389-goosky-rs4-landing-skid-gsk-gt020062-new-version (New Version) Goosky RS4 Landing Skid (Old version)
Designed this to fill the empty space leftover in most older Silverado Classic style trucks that ran from 1999 to late 2006 (mine is technically a 2007 model year). My phone has a magnetic case ( MagBak ) so I used a magnetic wireless…
EN Audi A3 TT A5 - VW Golf 6 - 7 Headlight Washer Nozzle IT Audi A3 TT A5 - VW Golf 6 - 7 ugello lavafari
Stay Alive - Swink Sylvania (Frankie Muniz) & Hutch Macneil (Jon Foster) - 2006 3D printable model.
https://cad.onshape.com/documents/c8e8ca89eb6567ed4a442a5c/w/f4c2778f42168fe988feea3a/e/ab76905e51ded16ee7d8fe93?renderMode=0&uiState=6944de2c005aa8451a0bc176
Consider buying the metal interlock upgrade that is available online. However, I 3D printed a couple of these out of CF PETG and they have lasted several years so far. Make sure the new interlock rotates freely on the shifter assembly and…
my handle broke so i deigned the new part to fix it. just mirror the file to get the left and right side please printed in petg supports 100% infill
Palm rest for 200-600mm lens Category: Gadgets
Charmed - Props - Witch Wars Dagger - 1998-2006 3D printable model.
Can be used without a wrench Made to fit the awkward small space around the oil filter in the engine bay 65mm outer diameter Thread size 3/4" 16 UNF-2B I printed it on an MK3S+ w/ 0.6mm nozzle, 0.4mm layer height.
