Counting matching models…
Dragon Burner remix for BLTouch/3DTouch. OnShape: https://cad.onshape.com/documents/f649feacb89f1004466cba88 Offsets (from OnShape): X: +32.950 mm Y: -10.718 mm
After receiving a Creality Sprite Pro extruder to upgrade an Ender 3 Pro printer, I found that my touch sensor was hanging just below the hot end nozzle. I found several models via Printables and Thingiverse but could not find one I…
This model was designed when i found that my lateral remix with overrun of -20mm was getting tilted for the bowden cable under lateral tensión. so i made this one to try, so far works well, but i'm a little concerned on thermal…
Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the…
Very simple test to print and manual adjust the level of your printbed (Adjust the offset) when you just installed your ABL or changed the nozzle. Adjust width and depth size in your slicer to match your buildplate but beware to not…
Print, orientation and setting are the same as for any printed work for Voron.
original stl provided with kingroon doesn't fits my printer :( it's just too high and nozzle hits the bed :( so I've modeled simplest possible mount link to onShape project to edit:…
Držák 3D touch pro tiskárny kingroon kp3s. Použité šroubky a matice M3. Není nutné sundávat kryt extruderu. Tisk vrstva 0,1 nebo menší. 3 perimetry, materiál Petg. Bez podpory.
Made a cover for my 3D touch and a variant for a BLtouch as well BL touch cover will require supports Category: 3D Printing
A BLTouch or 3D touch probe mount for your SV08. Do NOT use the 24v power pin on the connector and use an alternative 5V pin. It will require a modified toolhead cover to allow for the fit as it sticks out the side. Use my alternative…
remix to give cat ears to the cowl
Anet A8 BLTouch Mount - Right Side - Inline with Nozzle There are a lot of Anet A8 3D Touch mounts out there, but none met my needs. I wanted the probe on the right side and inline with the nozzle, not in front or behind it. I designed…
This is a remix of JohnTran_309510's Ender S1 Sprite Extruder CR-Touch Mount, for use with sensors other than the Creality CRTouch probe. There are two versions of the mount itself. The file named “BL2CRTouch_Mount.stl” has a provision…
Remix of BLTouch Light Blocker - Probe Protector by Domush outside rounded and smoothed, honeycomb holes added to still let some light out. this design clips on super easy and holds on very well I do recommend using black filament to get…
for Creality Ender 3/pro
This is a bracket to mount a 3DTouch on a CR-10 or an Ender 3 printer. Support material is not required. An infill of 20% is recommended. This object main web page is: http://www.ctheroux.com/3dtouch-cr-10-ender-3-mounting-bracket/. This…
We've designed the lightweight mounter for the 4010 Hotend Fan, 5015 Section Fan, and 3D touch to the Titan Extruder model and share it. The sensor layout we have to describe in robin_nano_cfg.txt of the 3D-touch compatible firmware…
3D/BLTouch mount that uses less space than other mounts. Optimised for Satsana Fan Covers (Ender 3 V2).
3DTouch sensor mount for the Ender 3 works perfect for ender 3 aliexpress 3dtouch sensor offsets X-42 Y-5 Rafts: No Supports: No Resolution: 0.20 Infill: 25%
This is a remix of bltouch and 3d touch mount for Ender 3 Max, same geometry but with this mount the bltouch can be placed rotated 180º so the board is facing the fan and the wiring is less exposed. Enlarged a little bit the holes for nut…
I've added the 3DTouch sensor to the Bondtech BMG Prusa extruder. Personally I don't like the inductive sensor as the detection height depends on the thickness of your steel sheet bed, which means if you have low quality spring steel…
Got this direct drive which is for an ender 3 from a friend and thought I would try to use it on my Megazero 2.0 I also have Ender 3 V2 which is already heavily modified so it does not need this... :) This kit comes with all nessessary…
Designed to be printable without support. With 3 x 0.4mm perimeters it will be almost solid. Print it with any infill
3DTouch ( https://aliexpi.com/EWr7 ) mount for a Mellow BMG Wind extruder ( https://aliexpi.com/twlM ) Both normal and volcano compatable, for volcano mount your BLTouch from the bottom and from the top for normal E3DV6 (see photos) To…
I recently upgraded my old CTC A10s with a 32 bit silent board and bed level sensor. The A10s is a cheap knockoff of the Creality CR-10 and uses a nearly identical hotend and carriage to the CR-10, so I was looking for a bracket I could…
Mounted above the limit switch. The position on the print table is show.
This is just a simple 3DTouch/BLTouch mount for the Ender3v2 Carriage. I had originally chopped up someone elses design to make it work for me but decided to complete redesign one from scratch. Print Settings Printer Brand: Creality…
I needed a simple fan mount with including 3d touch on the side. Made my own and does the job well. Make sure to adjust the nozzle - probe distance x/y in marlin. Mine is " #define X_PROBE_OFFSET_FROM_EXTRUDER 41 " " #define…
made a mount that works with stock fan shroud
This design is for using a touch type sensor in place of the inductive sensor that ships with the Sovol SV06 extruder. My measured X and Y offsets, probe to nozzle tip offsets are: X=35mm Y=-27mm I don't know what the factory firmware…
BLTouch / 3DTouch and adxl345 Sensor Mount for BIQU H2 Wenn dir mein Modell gefällt, würde ich mich über ein like freuen If you like my model, I would be happy about a Like
This is a holder for the BLTouch / 3DTouch sensor meant to be mounted behind the radial cooling fan. Initially I designed this for my Anet A8 in combination with the "Mistral 2.1a" fan duct from user Neo_N (…
Anycubic Kobra mount for BLTouch/3DTouch, installs on place of original probe, stock probe mount can be used as a backplate that bolts go in (also you need longer bolts, i used ones that came with my 3DTouch). Compatible with 5015 fan duct.
This design is for using a touch type sensor in place of the inductive sensor that ships with the Sovol SV06 extruder and adds a location for attaching my signature skull & wrenches ornament. My measured X and Y offsets, probe to nozzle…
I've designed this simple part to mount the 3DTouch bed levelling sensor into the Tevo Tarantula PRO. It's working well, can be used with a single longer screw or two short ones. As in picture, I've wrapped it as well as the BLtouch under…
An attempt to mount 3d Touch Sensor to the Zonestar P802Q (steel) carriage. V1 is light version with single bolt fastening. A part of the sensor's PCB is not protected. V2 with a more massive mount on two bolts and full PCB protection.…
This mod adds the ability to attach a 3D/BL Touch sensor instead of the 12mm inductive sensor. As it is a modular design ( https://www.thingiverse.com/thing:2777161 ), the backplate does not have to be reprinted again. Height is…
Fan mount for NFSunrise extruder, remixed from qnub on Thingiverse: https://www.thingiverse.com/thing:4875476 . Modified to fit Volcano extruder (greater height), and to fit either a 3DTouch/BLTouch level probe, or a SuperPinda or similar…
Soporte simple para colocar un BlTouch o 3DTouch en el extrusor doble de HTA3D. Category: 3D Printer Parts
You need a firmware modification for 3d touch. https://www.thingiverse.com/thing:5193964 for firmwares Category: 3D Printer Parts
This is a very specific model for my heavily modified Anet A6, to turn it into a plotter. I use this guide, and the model is for the knives recommended there: https://nmeurer.de/2020/08/schneideplotter-aus-3d-drucker-der-20e-cameo-killer/
Introducing an Optimal BLTouch Mount for Ender 3, Aquila, and Similar 3D Printers Greetings to the vibrant community of Printables enthusiasts, To all fans and users of the Ender 3, Aquila, and other similar 3D printers, I have…
This is a remixed touch probe mount for the der Skorpian fan duct (https://www.printables.com/model/18904-der-skorpion-fan-duct-for-geeetech-a10m-and-a20m-d) for the Geetech A20M to allow the use of a 3DTouch probe. The 3DTouch and…
I bought a new 3D Touch 3.2 and it's larger than the older one and needs a different mount. This mount will fit on the right side of the printhead partly tucked behind the fan. Mirror it to mount it on the left or it will interfere with…
This clip helps to secure the BLTouch / 3D Touch bed leveling wires (even fan wires) and prevents those wires from flailing around while printing. Updated 06Aug19 - File Rev. 3 - Made both ends of the clip the same shape without losing…
Soporte para montar 3DTouch v3.2 PRO (BLTouch) en Ender 3v2 con el minisatsana dual fan 4010. Este soporte hace que toque un pelin antes el final de carrera en el eje X. Imprimir en material como PETG, el mio esta hecho en PETG de…
