Counting matching models…
Here's a a few simple boots for 64oz, 32-40oz and 12-20oz Hydro Flasks. There is also a version for the narrow top Hydro Flask and the Tumbler Hydro Flask . Please note, this MUST be printed in TPU to fit as rigid filaments will not work.…
This is a TAL Ranger lid, it fits the 18, 40 and 64oz bottles, it is designed to use the o-ring that is in the original lid. 2 models will be uploaded, one I added ribs and a D-ring hole to hook to something and the other is smooth with…
Yeti drink bottle holder for the 64oz. Holder can bolt to a 55mm post
Cupholder adapter for 64oz Takeya steel waterbottle 1 piece print with no supports Printed in PETG since it will be used in a hot car Dimensions: Section that goes into cupholder: h=2.500in, d_outer=3.180in Section that waterbottle slides…
Feed wild birds with this bird feeder that attaches to a 2 or 1.89 (64oz) liter bottle. rivet a chain to a bottle for a secure hold. I also attached a 2 and 1.89 liter bottle funnel. Use no top or bottom layers and a high infill (75%+) to…
Reinforced replacement handle for TAL 64oz water bottles
The original model did not work with a 1.9L/64oz Mason jar. This fits snug, so it won't slide off. Print body in vase mode
Protective boot for a 64oz Hydro Flask. Print with 10% infil gyroid. Print instructions Category: Household Summary Protective boot for a 64oz Hydro Flask. Print with 10% infil gyroid. Print Settings Printer Brand: Creality Printer: Ender…
Rings print with no supports. Handle can print without on a dialed in printer, however, adding supports only means you need a little clean up if you want that assurance of no dangle strings. Multiple sizes available to accommodate slight…
Cup holder adapter to fit the large XPAC 64oz insulated tumbler in a Model 3 cup holder.
The base of the extension is measured off the large cup holder in a 2001 Jeep Grand Cherokee.
This is an extremely large print for (2012) Audi A3 owners (maybe other Audi's as well) to drop into the two-stage cup holder size we have. 207.50mm (X) × 200mm (Y) × 217.40mm (Z). It's off-center 7.5mm to move it slightly toward the…
A cupholder solution for your 64oz Hydro Flask in a Jeep Wrangler JL/JLU! A 64oz Hydro Flask doesn't fit into either of the the cupholder compartments of a Jeep Wrangler JL/JLU due to the water bottle's enormous 4.72in diameter. Unlike…
Did you break the handle on that great 64oz growler / water bottle you got at ALDI or maybe on Amazon? Use this model to print a replacement. The handle is attached to the growler's lid with a metal pin you can poke and pull out using a…
A boot for the 64oz Iron Flask, 125mm ID, printed in Bambu TPU 95A HF. Printed with 3 walls and 15% hexagon infill. Prints fast, uses little TPU, works like a charm and fits perfectly.
I got the Manna 64 oz growler with 4 cups from Costco and its great to be able to have 4 cups together with a large thermos. However the cups are quite thin and get a bit hot to hold without the handle so this solved my problem of burnt…
21oz and 64oz versions are in the works, check back in a bit! My LTT water bottle was a bit too loud for me when setting it down on a table. This bump sleeve not also quiets it down a lot but also protects your hydration container from…
I made this because I was tired of having to be extra careful when placing down my water jug while in quiet places.
The rubber handle of my Iron Flask wore out and broke after a couple years. The bottle is a pain to carry around without a handle due to the weight so I designed this. Print on either side, no supports needed. Just remove the two pins on…
New and improved handle for the old, squat 64oz Hydroflask growler. My original was cracking at the corner of the ring so it was time for a new one. Required hardware: 4x M3x25 SHCS, 4x M3 square nuts Changes include: Thinner ring band…
I got the Manna 64 oz growler with 4 cups from Costco and its great to be able to have 4 cups together with a large thermos. However the cups are quite thin and get a bit hot to hold without the handle so this solved my problem of burnt…
The rubber handle of my Iron Flask wore out and broke after a couple years. The bottle is a pain to carry around without a handle due to the weight so I designed this. Print on either side, no supports needed. Just remove the two pins on…
A simple hook to hang your 64oz water bottle from existing water bottle holders that are too small for the bottle. Can also be used on chain link fences. Print Settings: Material: PETG Infill: 20% Perimeters: 4 Nozzle: 0.6mm
After somehow loosing my 64oz Hydroflask I ended up buying a 64oz Stanley. I wanted an airtag somewhere but didn't want something dangling from it. This disc allows for you to drop an AirTag underneath the bottle if you have a silicone…
Bottle handle fix for 64oz glass water bottle. I would recommend printing in a strong filament, such as PC/ABS. The bottle cap insert is what interfaces with the inside of the bearing/bottle cap and the handle fix interfaces with the…
I recommend hand washing only for this part. I printed mine in ASA, but there may be some higher temp filaments that could survive the dishwasher.
I designed this o-ring to be printed out of TPU and tucked into this lid designed for the TAL ranger pro by Dznutz. It should also work with the original lid.
For the top of the Yeti its a mostly snug fit. (Yeti Bottom in Blue also in Pic)
This is just a simple shroud for a large yeti water bottle. it can be make in either TPU or PLA but we got better results with the PLA but that could be due to my quality of TPU (amazon basics...) UPDATE: tightened the tolerance of the…
A simple adapter to use an Aerogarden pod in a 64oz Mason jar.
YETI Dog Bowl Riser Stand for 64oz or 66oz bowls Raises bowl about 230mm at bottom, model itself is 250mm tall print upside down, only needs supports for the indented part where the bowl will go Included is a piece that allows 2 stands to…
