Counting matching models…
The metric system is great, but sometimes you need an inch based version. These knobs are for 1/4-in and 5/16-inch bolts or nuts, and can be used in either the male or female version with the appropriate additional hardware (as shown in…
2x6 Gridfinity Mitutoyo 6in caliper holder.
I didn't want to spend 12 dollars and wait for shipping, so I whipped this up based on my fuel lines and images online. It took a few tries to get the width of the central ‘sleeve’ the in the sweet spot. Thin enough to fit, but thick…
Recommended items to complete this crane are hot glue, BBQ skewers, Popsicle sticks, rubber bands, 30 minute epoxy, kite string, small-sized hand-held drill and bits, four 360 degree rotating 9 gram servos, one receiver, transmitter, and…
Created using Zack Freedman's Fusion template: https://a360.co/3ccHbsg Copyright (c) 2023 Zachary Freedman and Voidstar Lab LLC
I have an updated version at the following link https://www.printables.com/model/753753-3d-printed-marching-tenors-with-attachements Small tunable drums using standard drum heads and 10-32 x 1-1/2" screws. This was modeled in Fusion 360.…
These are bins designed specifically to hold Mitutoyo digital calipers for Zach Freedman's Gridfinity system. I designed them around models 500-195-30 (4"), 500-196-30 (6”), and 500-197-30 (8”), but they may also fit other brands or…
Credit to @Jonathanlin for including the f3d file that made this an easy first remix! I did slightly reduce the diameter on the side that connects to the Cloudline S6, the fit is very tight so make sure your printer is well calibrated. I…
Available in two versions: 15cm / 6in 10cm / 4in Now you can make perfectly parallel lines on your paper, woodwork, etc. In addition to the horizontal distance (15cm/6in or 10cm/4in), I added markers for vertical distance between lines (…
This is a remix of @Cheshire_Wolf_516454 Mitutoyo caliber hold to include storage
The Ocean Wave Picture Holder is ideal for showcasing a 4in X 6in beach photo or a child's first surfing success. The 4in X 6in photo can either be placed directly in the wave, or attached to the optional simple frame print and then…
I designed a 3d printable snare drum with minimal supports. Material: PETG recommended for stronger lugs Hardware: 4x Drum Lugs 4x Drum Lug screws 1x 6" Drum Hoop
Pretty basic idea: 6in Tapered Candle Mold. Just print both halves, bottom up with organic supports - to hopefully produce as smooth a mold as possible. Should produce a tapered candle about 6 inches long with a ¾ inch base. I'll post…
Created using Zack Freedman's Fusion template: https://a360.co/3ccHbsg Copyright (c) 2023 Zachary Freedman and Voidstar Lab LLC
5in (5in I.D 5.12OD) 6in(6.12in ID 6.24in OD) 4.5in high. Designed to attach the Harbor Freight 2hp Dust Collector 5in inlet directly to the outlet of the Oneida 4/5 Super Dust Deputy cyclone. Print time with PLA and standard Cura…
This 3D Printable Worm Mold is for a Big Boi 6 Inch Plastic Worm. Throw an O-ring on it and Huge Largemouth Bass will find it irresistible. I'm currently in the middle of testing durable Biodegradable Options over Plastisol but for the…
A decorated designed tiles to mount on the wall. Can be mounted in 2x2, 3x3 or 4x4 array. Each tile is 22cm by 22cm (8.6in) Print is optimized for minimal filament consumption while keeping solid structure Inspired by the design of…
This functional 3D-printed laptop stand is designed for the MacBook Pro 16-inch model. It features a separate piece that holds the cables in place, which is then inserted into the main body to lock them securely. This prevents the cables…
Remixed the excellent 6in magnetic duct system to allow for a 4in version and also add a 5in collar that fits the 6in
Based my design off of Jok's. Increased the size to accommodate fitting onto a 6" (150mm) exhaust fan and 6" exhaust duct made from standard HVAC sheetmetal parts. Also added magnets to the housing and gate to allow it to stay fully open…
Used on my bosch GEX 18V-125 at home and with a compressed air 150mm 3m one at work I designed it to print as quickly as possible and use a minimal amount of material.
Hello! I present you with a holder for the Milwaukee fastback 6 in 1 knife, designed to be used with Ikea Skadis board. I recommend printing it as shown on photos, I used 0.12 layer height, tree supports and gyroid infill. Have fun!
This is a heat exchanger for 6in ducting. As an example, I used it to temper incoming makeup air for a basement kitchen hood's exhaust. I printed using carbon fiber reinforced PLA. I don't have the equipment or knowledge to test the…
Lost the wheel and axle assembly on a fishing trip. this not only made it cumbersome to move the cooler, the wheels act to stabilize the unit. Its a decent cooler and I couldnt toss it in the dumpster just because I lost the wheels.…
This design has 8x8 holes to allow for up to 4 squares at a time granted the board itself is 6inx6in but can easily be scaled to fit your needs. I made the pegs with tapered bottoms so they will fit snuggly
Ring adapter for 4 door speakers. Door bots with 5mm@10mm. (158mm standard door fixed bolts) Speakers fixed with drywall 5/8 (143mm diameter) Standard fix for 6in speakers.(not 6.25 or 6.5mm) ... Adaptador para VW GOLF, Jetta, Bora para…
A few parts for my Craftsman Bench Grinder. Bulb shade is extended so one can use automotive blinker bulbs. Glue some aluminum foil inside to act as a reflector. Bulb Shade - Part #21126025 Knob - Part #21126010 Tool Rest - Part #21126035…
.3 mm layer height works fine. 10% infill. Let me know if it works with other brands so I can update this page.
The silver model here was printed in PLA with 0.20mm layers but 0 top and bottom layers to let the infill show thru.
This is a print to add an inline filter to 6in ductwork. I used it for a fresh-air intake for a house, but it could be used for many air filtration needs! For 6in diameter ductwork. Neodymium magnets: (12) 10x3mm cylinder (4) 20x10x3mm…
Ripper/Cutter is screwed into the kitchen cabinet alongside with any paper towel holder you have or print. Slide in any regular kitchen paper towel up to the width of 27cm/10.6in! Print: Upside down, with organic supports, low infill.…
Used magnets: 6mm x 2mm (6 each) The male adapter has a protruding lip in order to make a better seal against leaking gases or vocs. It's also possible to simply connect two female adapters. These are quicker and easier to print but don't…
Just a basic remix for a Stanley 5m tape measure. I have not tested it as I printed the original one and cut out the needed shape. Any feedback is welcome 21/04/25 After feedback from a maker, it fits the tape well as well as a Stanley 16…
Needed a 5/16in bolt knob for a few projects so I designed one. This was designed particularly for the AMD 5/16in hex bolt from Home Depot. I like to super-glue the bolt in the slot and cover it up with a washer to protect the knob as…
I designed this 6in dust pipe fitting to work in conjunction with a 4in dust pipe fitting ( link ) for mounting my pipes to the ceiling of my basement shop. Since my shop has low ceilings I needed to keep the pipe very close to the…
Here I only uploaded the 3D files for the button ring. For the whole project, there're also electronics and firmware stuff. Go checkout in my project repo, there's a detailed guide: whowechina/mai_pico: Pico controller for Maimai…
Test dummy model based on a 5ft 6in tall female with average proportions. Model set as public domain and free for any use.
Very nice and light sheath by @MatthewGTaylor , rescaled to fit the 14cm/6in version of the knife. I like to take this knife with me for cooking on my travels, so a sheath is a must. This is my first remix: please let me know in comments…
slight re work of someones design to add a smooth insert plug and shrink the back size a bit. prints in about 17 minutes
Modell ist mit Fuzzy-Skin gedruckt. Montierter Griff: https://www.printables.com/model/181455-angled-vertical-foregrip-m-lok Step-File ist für individuelle Anpassungen auch hochgeladen
The Kakapo's Orchid Planter for Oversized Orchids The planter was born as a solution to save our dying orchid. It needed space and the old plant pot wasn't going to fit it. This 6-inch beast is not only satisfactory for the orchid but is…
No Solicitation Sign (6in Wide)
I was wondering about the original stand and I’ve modified to allow more support for a heavier macbook.
Printed with 5% infill, 0.4mm nozzle A simple stand for a 6in hoop ring used for punch needle projects. Stand is deep enough to use a punch needle and not scrap a table under the ring. Also provides enough support for punch needle…
Please see here for the complete file package: https://www.printables.com/model/632833-range-hood-window-exhaust --- This is an adaptor to mate a 6 inch air duct to the window exhaust vent here: https://www.amazon.com/dp/B0BV68L8DY. I…
A Stand for a 16inch+case macbook pro (I didn't design it it was made by jens j).
A privacy cover/shield for the camera of the MacBook Pro 16 inches 2019 model. It is a tight fit to not have it flop about the whole time. But this might mean you need to scale it according to your printer. There are two files since I'm…
A coupler for 6 inch ducting. Uses magnets that are inserted by pausing the print partway then resuming the print. The magnets I used were sold as 6mm x 2mm, but measured as 6.02mm x 1.72mm. Insert a pause event before the layer that…
This is a simple 6in bongo drum with a 0.8 mm thick drum surface. Print upside down at 0.2mm layer height with 4 bottom layers to have a solid drum surface. The rest can be printed at whatever infill density desired. Enjoy!
Stand for 2 MacBook Pro M1 Pro 16inch, remixed from an existing model from here. No support needed. For best durability, print it vertical. It is a 3D printable stand that can be used to prop up two MacBook Pro M1 Pro 16-inch laptops. I…
This is designed after a cheap 15.6 inch monitor I bought on Amazon. It has a VESA 75 Mount on the back. On the left side I modeled the On/Off as well as the menu selector. There is also a 3.5mm headphone connector. On the right there are…
This is the v2 of the 6" version of the Tubular frame. The v1 was my first frame of this type, and i had an amazing time with it. Since then, the frame design has been much improved, so this version incorporates them all. i have worked…
Print two. A hose clamp will hold them together, so the seam only needs glue or tape to seal. Fitting the duct on is very snug. Made with 0.4mm increments in mind for 0.4mm layer heights.
I made this jig so I could make a corner with a 6in radius on a cabinet I am building. I will use a jig saw or band saw to remove a majority of the material then a spiral pattern bit to reference the jig to make it perfect.
I designed these 3x6 passive wall registers to add a decorative touch to any passive wall vent. I printed these in PLA and they're pretty sturdy but would only use these for passive holes that aren't exposed to heat or stress from being…
Works reasonably well. Is a little difficult to line up the threads and not crossthread it when screwing on the lid. Easy enough to print. As always FreeCAD model is available if anyone wants to modify it.
Game insert design is built using the mask created by xls38_1520611 This is designed for the pocket version of Hive and will hold the Mosquito, Ladybug and Pillbug expansion pieces.
Simple potted plan water drain catch for pots ~6" in diameter!
We modified the source model to adjust the inner-diameter for fitting the 1.46in Electronics Pole for Outside Home Antenna Installation . Used metal screws to secure the printed part to the Pole, and the RTK screws in on the top.
Replacement jaws for 6in Irwin vices. The jaw should printed out of a durable material- the original is ABS and is holding up well. It is attached to the vice using the screws that hold the stock jaws on and the soft jaw insert is slid in…
The original creator's design is great, however it was a bit too short for my calipers so I had to extend the length a bit. I also added storage for 8x6 = 48 precision screwdriver bits (4mm), as well as small cutouts for four LR-44…
Hello! During the construction of the new high school I'm currently attending, the construction crew gave us a crap ton of new Color Source Pars with no diffusers or gel frames, and therefore we had to take things into our own hands and…
I needed a way to affix my super dust deputy directly to my harbor freight 2.5hp dust collector. I designed this off the 6 to 4 inch adapter that came with the cyclone and modeled this off exact dimensions measured and as I printed is an…
This scraper uses a standard straight razor which fits tightly in the slot at the end of the tool. Depending on the printer, the slot may have to be cut with the razor the first time it's used. I printed this one in CR-PETG (red) at 235C…
I have a set of 6in 3 and 4 jaw chucks from precision matthews. The jaws are 20mm wide each and are pretty similar. I suspect it will work for most chucks in that size. the 4 jaw has 90 degree cuts and the 3 jaw has 120 so they all come…
A simple combat gauge for Warhammer. 6inch by 1inch by 0,12inch. Each square is 1inch by 1inch. Done in 40 minutes of less.
The organizer required: Husky 6 in. 6-Compartment Storage Bin Small Parts Organizer -Write in part number or letter on each bin's chamfered front edge -Include double wide bins where more storage space is needed
I was replacing the Delta faucet cartridge for our single handle kitchen sink and the instructions specified a 1-5/16 six point socket. I tried to buy one at Lowes and Home Depot stores locally, but they did not have that size. I then…
A lot of nice stirrers out there already, but I needed one that was about 6 in long and able to be put in a hand drill for stirring 2-part epoxy.
Stand for 4 MacBook Pro M1 Pro 16inch, remixed from an existing model. No support needed. For best durability, print it vertical. It is a 3D printable stand that can be used to prop up four MacBook Pro M1 Pro 16-inch laptops. I printed it…
My LED lights that had trim included burnt out and I didn't want to spend $30 a piece on replacements so LED bulbs and 3D printed trim pieces to the rescue
MadCow makes a great rocket, but some of their pseudo-scale birds need some tarting up, so that's what I did: I created a fairing, a blackout disk for behind the fairing, and a nozzle for the back. Makes the ramjet nacelles look a little…
Automated active self-watering orchid system. Orchid is placed in the top half, the bottom is filled up with water. A lid separates the two parts. At set day intervals, the water is pumped up and soaks the orchid for 2 minutes before…
Version 2 has been released! It has been much improved upon. Find it here: https://www.printables.com/model/408649-tubular-6inch-v2-freestyle-frame-superlight-and-su -------------------------- This is the 6" version of the Tubular frame…
Created using Zack Freedman's Fusion template: https://a360.co/3ccHbsg Copyright (c) 2023 Zachary Freedman and Voidstar Lab LLC
I designed these 3x6 passive wall registers to add a decorative touch to any passive wall vent. I printed these in PLA and they're pretty sturdy but would only use these for passive holes that aren't exposed to heat or stress from being…
Allows the attachment of 6in ducting to the back of the exhaust fan. Overkill for the amount of air from the fan but designed for grow-tent carbon filters. Print in two pieces then join with four M3 screws and/or glue. Clips into the back…
Allows direct connection of 6in AC hose to 8in VEVOR inline fan. Small dia side fits inside the AC hose, large side fits outside the rim of the fan intake. Designed to friction fit to allow quick connection. OnShape Link This is part of…
introducing the XtremeWorks 6-inch joystick clip-on extender! this will win all your games from that 1 vs 1 COD game to letting that one friend with hella long thumbs stop complaining about how short the sticks are! Now on maker world!…
Sanding Grit label 6in/150mm print with Prusament Orange and Black PETG .
-PETG -no support -any % infill 2023/01/18, MN
This is meant to cover the unsightly hole in the ceiling that the microwave vent goes into to make everything cleaner. The diameter of the center opening is 6.15 inches. The walls are 2mm thick. The outer diameter is about 7.5 inches.…
i used four Walmart generic brand poster command strips and it has worked fine
BearQuads Kodiak 6inch racing frame with braces TPU parts You can find the frame here: https://armattanproductions.com/pages/product_details/17330 Frame braces: https://armattanproductions.com/pages/product_details/17325…
Created using Zack Freedman's Fusion template: https://a360.co/3ccHbsg Copyright (c) 2023 Zachary Freedman and Voidstar Lab LLC
Print in PETG, this thing gets hot and PLA will deform. There's two top cover versions, one for HappyModel and another one for "Rcharlance" branded one. Category: R/C Vehicles
Use a decent PLA or PETG for this and it should be able to handle reasonably small loads, such as holding lids down or the like. No guarantees as to heavy loads though.
I needed to mount the hub below monitor, but above monitor stand. You can print one front and one back holder part or two back (standing) parts if you do not need to attach it to the shelf edge. If you need to modify this project it is…
I created two sanding guides to help me either draw the parabola shapes (or ideally, sand the shapes) of the conduit ends of the MadCow 2.6in BOMARC. I then created an alignment guide to help position the ramjet cones when applying epoxy…
I wanted to add lights to my Prusa MK3 to make prints easier to see, and for monitoring when I may want the room lights off. This design uses a 6in LED strip, and is mounted with 3mm bolts. I use one light on each side of the top frame.…
Hello Owners of these chargers know that after a long time of using this plate, it warms up very much. I decided to design a cooling system to not burn the charger or home: P Necessary parts: screws: M3 6mm (legs) 8mm (fan) Print Settings…
Display case that uses acrylic panels with dimensions 16in x 12in x 6mm and 12in x 12in x 6mm. Extras: 4 x D6A from K&J Magnetics 4 x D64-N52 from K&J Magnetics Remaining panels can be affixed with Magnet Replacement Peg or additional…
Short version of heltec v3 mount. Fits 6inch racks.
I wanted a way to hang my G9 random orbital on the wall that was compact and sturdy. This is what I came up with and it seems to work great!
Useful if you want to have a nice little try for 8x6x3 mailer boxes, this is the 3rd revision. i also have the files for the dividers but figured the empty version would be best to upload first. Recommended 2-3 walls and 2-3 top surface…
Made for the Zephyrus G16, or really any other 16 inch laptop with top/mid intakes. Required Parts 1x Faceplate 2x Legs Optional 1x Mid Leg 1x Brace Some foam to make a seal around the output Assembly I used just standard normal M4 bolts,…
un remix de ce support a raspberry Pi 3/4/5 rack 6in avec un écran oled 128x64 remix de https://www.printables.com/model/1173903-raspberry-pi-2b3b4b5b-6-inch-rack-mount/remixes et…
Skate guard for blades lengths 16-18 inch, comment on how to improve! BTW I do short track speedskating
Saucer 6inch 15cm Category: Outdoor & Garden
